Speed of Sound Lab Report Jamie Cook PHYS 1114: College Physics I Oklahoma City Community College December 10‚ 2013 Purpose: The purpose of this experiment is to measure the speed of sound in air and to determine the effects of frequency on the speed of sound. Apparatus (equipment used): Signal generator: manufacturer- EMCO‚ model number- SS-1‚ range- 20Hz-2MHz‚ least count- 1Hz Frequency meter: manufacturer- DEADALON CORPORATION‚ model number- N/A‚ range-
Premium Sound Speed Wavelength
Calorimetry Lab: Determining the Unknown Metal Purpose: To determine the identity of an unknown metal Hypothesis: The unknown metal is Copper Materials: * Safety glasses * Styrofoam cup * Thread or string * Glass rod * Thermometer * 100mL graduated cylinder * Hot plate * Balance * Unknown metal * 300mL beaker Procedure: i. Mass of metal was recorded ii. Water was heated on a hot plate in beaker iii. Temperature was recorded when water reached
Premium Heat Temperature Thermodynamics
Introduction The purpose of this lab is to examine the motion of an electron‚ when it encounters a constant magnetic and electric field. We will also observe when the electric field and magnetic field will cancel each other out. This will lead to the electron having no net force acting upon it. By adjusting the values for the magnetic and electric fields‚ we will be able to check the different paths the electron follows. From this data we will be able to calculate the charge-to-mass ratio. Then
Premium Chemistry Electron Magnetic field
LAB WRITE- UP NAME: MANOUCHEKA FIDEL DATE: 9/19/14 TITLE: BACK AND FOURTH MOTION PURPOSE (Introduction): To qualitatively analyze the motion of objects that move back and forth. Then analyze and interpret back and forth motion in kinematics graphs. Use kinematic graphs to catalog objects that exhibit similar motion. PRELIMINARY QUESTIONS: Finding the average velocity Do any of the four objects listed above move in similar ways? If so
Premium Classical mechanics Velocity Newton's laws of motion
Name: Lab 201: Electric Field by Point Charges Section: 121A-H02 Date: February 8‚ 2012 Objective: To compute electric field and corresponding field lines caused by point charges using MATLAB. Theoretical Background: -electrons are negative‚ protons are positive -magnitude of force between A and B is: ‚ is 8.98755E9. -electric field is the region around a charged object -strength of electric field: = -electric field lines are used to visually show the field Procedure: Our
Premium Electric charge
Solving Part A: Center of Mass in One Direction 1. Since the mass of the plate is a uniform‚ the center of mass is in the center of the plate. The plate has diameter d = 28 cm‚ thus the center of mass is 14 cm from the edge of the plate. In the lab‚ two scenarios will be analyzed; 1) when the glass is standing up‚ and 2) when the glass is laying on its side. When the glass is standing up‚ its mass is uniform about the axis of symmetry. Therefore‚ the horizontal center of mass will be at the exact
Premium Dimension Analytic geometry Mass
Central Philippine University ILOILO CITY‚ PHILIPPINES MATHEMATICS and PHYSICS DEPARTMENT Experiment No.___________________ Name _________________________________________ Course and Year ______________ I. Objective: -To determine and to identify the motion which the metal ball undergoes as it rolls down the acceleration board. II. Materials: Acceleration board‚ cornstarch‚ iron stand‚ clamp with iron bar‚ brass ball‚ PVC pipe‚ meter stick III. Procedure: 1. Using
Premium Light Iloilo City Time
Abstract :The purpose of the experiment is to explore elastic and inelastic collisions in order to study the conservation of momentum and energy. The guided track‚ carts‚ photogates ‚ 250 g weight and picket fences were the primary components used in the procedural part of the experiment. Each experiment involved the use of the photogates and picket fences to measure the initial and final velocities of both carts when they collide. The data was collected and translated to a graphical model for further
Free Kinetic energy Classical mechanics Introductory physics
Lab 1 – Measurement of Space and Time Anthony Lucci Lab Partner: Amy Hayes Question 4: Both the height and diameter of the cylinder were taken to find the volume; five times for both measurements. Vernier calipers were used to get these measurements by clamping the cylinder between the jaws of the calipers. By looking at the mark of the zero‚ in relation to the main scale‚ the line best lined up with a line from the main scale was taken down. Getting
Premium Measurement Errors and residuals in statistics Volume
Phil Yu Electrostatics Lab Data Chart Part 1: Trial | Material | Material | Charge (+ or -) | q (nC) | 1 | Glass | Fur | + | 3.108 | 2 | Clear Plastic | Fur | + | 45.07 | 3 | Yellow Plastic | Fur | - | 81.57 | 4 | Glass | Silk | + | 1.979 | 5 | Clear Plastic | Silk | + | 19.60 | 6 | Yellow Plastic | Silk | - | 75.49 | 7 | Glass | Green Cloth | + | 2.914 | 8 | Clear Plastic | Green Cloth | + | 31.09 | 9 | Yellow Plastic | Green Cloth | - | 90.30 | Data Chart Part 2:
Premium Electric charge Concentration