a horizontal plane until you can keep the paper clip a short distance just below the bottom of the tube. If the paper clip touches the bottom of the tube‚ then the clamp is no longer supplying the centripetal force. If the paper clips rises or falls appreciably as the stopper whirls then the radius of the circle is changing. B. Constant Radius and Variable Speed 3. With the paper clip against the tube and the string pulled taut‚ measure the length of the string from the top of the tube
Premium Mass Classical mechanics Force
is the capacitative reactance‚ R is the resistance‚ and ω = 2π f ( f is the linear frequency). Apparatus • PC with DataStudio installed • Science Workshop 750 USB Interface Box • Power Amplifier • Voltage Sensor • AC/DC Electronics Lab Board • LCR meter • Connecting patch cords Experimental Procedure The experimental procedure can be divided into three parts: Part I: Using a Frequency Scan to Determine the Resonance Frequency • The first
Premium Alternating current Inductor Electrical resistance
References: a) http://en.wikipedia.org/wiki/Reynolds_number b) http://www.engineeringtoolbox.com/reynolds-number-d_237.html c) http://www.engineeringtoolbox.com/laminar-transitional-turbulent-flow-d_577.html d) http://www.slashdocs.com/prqt/lab-report-osbourne-reynolds-apparatus.html APPENDIX The Reynolds Apparatus that was used during the experiment.
Premium Fluid dynamics Fluid mechanics Viscosity
References: http://webs.mn.catholic.edu.au/physics/emery/measurement.htm#Measurement http://www.digipac.ca/chemical/sigfigs/experimental_errors.htm http://www.tsb.gc.ca/eng/rapports-reports/rail/2011/r11v0057/r11v0057.pdf
Premium Experiment Science Design of experiments
Muhammad Ali Jinnah University Islamabad Applied Physics Lab Project Report [ BRIDGE RECTIFIER] Group Members MIRZA UMAIR SAFDAR EE-123076 HAMZA BIN TARIQ EE-123086 Section PHY 7 Submitted To Ma’am Javeriah Iftikhar Abbasi Physics lab project Introduction: In this project we have created a device which takes input of 220 volts of ALTERNATING SOURCE and it gives us out put of 5 volts of DIRECT CURRENT for this purpose we have used various electronic components as
Premium Rectifier Alternating current Direct current
The Virtual Lab – ELISA Test Lab: Immunology 09/04/2013 Instructors: Dr. Charlie Wilson Written by: Dipen Patel I. Objective: The purpose of the lab was to learn the procedure of performing an ELISA test to determine whether a particular antibody is present in a patient’s blood sample. ELISA is an abbreviation for “Enzyme-linked Immunosorbent Assay." II. Introduction: The interaction of antigen and antibody outside the body can be used to determine if patient
Premium Antibody Immune system ELISA
McLean 1 Creating Acetylene Gas Introduction The purpose of the lab was to determine the ratio of air to acetylene results in complete combustion of acetylene gas. The balanced chemical equation for this experiment was C2H2(g) + O2(g) --> CO2(g)+ H2O(l). Complete combustion is the reaction of an element or compound with oxygen to produce the most common oxides and energy. Complete combustion occurs when the fuel and oxygen combine in exact proportions to completely burn the fuel
Premium Oxygen Combustion
Example lab report of Synthesis of potassium tris (oxalato) ferrate (III) trihydrate Posted by Nurul Yunaliyana Experiment 5: Synthesis of potassium tris (oxalato) ferrate (III) trihydrate Purpose: to synthesis potassium tris (oxalato) ferrate (III) trihydrate ‚K3 [Fe (C2O4)3].3H2O. Introduction: Ferrous ammonium sulfate‚ Fe(NH4)2(SO4)2.6H2O is dissolved in a slightly acid solution‚ excess oxalic acid‚ H2C2O4‚ is added and the following reaction takes place: Fe(NH4)2(SO4)2.6H2O + H2C3O4
Premium Chemistry Iron Ammonia
City University of Hong Kong Dept. of Physics & Materials Science AP2104 Mechanics of Solids Laboratory Manual Experiment 1 Pure Bending of a Beam Experiment 2 Torsional Deformations Experiment 3 Yield Criteria for Ductile Materials under Plane Stresses Experiment 1 Pure Bending of a Beam Objective 1. To examine the stresses at various positions of the beam under a constant load of pure bending. 2. To determine the curvature of deflection of the beam. Introduction
Premium Force Torque Shear stress
One of the main learning experiences of this lab is to learn the importance of calibrating a sensor. In most cases‚ a sensor will not have an output that is exactly what you need. An example of this is a strain gage. A stain gage gives back a voltage‚ but with that given voltage a distance can be found. Introduction: In this experiment‚ the QNET-MECHKIT was used. This board has multiple compact sensors that can be used for experiments. For this lab we will be using the strain gage to find the
Premium Metrology Measurement Angle