Data‚ Results‚ Calculations and Discussions Preparation of 250-mL 0.1 M NaOH Solution: Wt. of NaOH= (vol. of Sol’n) (M of Sol’n) (MW of NaOH) = (250 mL) (0.1 M NaoH) (40.0g/mol NaOH) Wt. of NaOH= 1.00 g • One gram of NaOH pellets was weighed and dissolved in distilled water. The solution was diluted to 250 mL. Table 1.Weighing of KHP (weighing by difference) |Replicate |Wt. of container -sample‚ g |Wt. of KHP
Premium Derivative Titration PH
Analysis of Soda Ash and Carbonate-Bicarbonate Mixture Submitted: February 27‚ 2013 Department of Chemical Engineering‚ Faculty of Engineering University of Santo Tomas España‚ Manila Abstract A standard acid solution like HCl can be used as titrant for the analysis of both soda ash and a carbonate-bicarbonate mixture. In the analysis of soda ash‚ the volume needed to neutralize the soda ash is used to compute for its alkalinity‚ in this experiment we obtained a 17.6 % alkalinity with an error
Premium PH Sodium hydroxide PH indicator
hydroxide (NaOH) pellets Potassium acid phthalate (HKC8H4O4) Phenolphthalein Soft drinks samples B. Apparatus 250-ml beaker 250-ml Erlenmeyer flask 100-ml volumetric flask 50-ml buret 10-ml pipet buret holder Stirring rod triple beam balance Bunsen burner Iron stand and ring wire gauze III. Schematic diagram of the procedure IV. Data and Observations Table 1.1. Preparation of the Sodium hydroxide solution Mass before standing Mass after standing Beaker (g) beaker and NaOH pellets(g)
Premium Sodium hydroxide Carbon dioxide Acid
hydroxide (NaOH) pellets Potassium acid phthalate (HKC8H4O4) Phenolphthalein Soft drinks samples B. Apparatus 250-ml beaker 250-ml Erlenmeyer flask 100-ml volumetric flask 50-ml buret 10-ml pipet buret holder Stirring rod triple beam balance Bunsen burner Iron stand and ring wire gauze III. Schematic diagram of the procedure IV. Data and Observations Table 1.1. Preparation of the Sodium hydroxide solution Mass before standing Mass after standing Beaker (g) beaker and NaOH pellets(g)
Premium Sodium hydroxide Carbon dioxide Acid
(2) To specifically use solution stoichiometry to determine the percent of acetic acid in vinegar. (3) To prepare a standard solution by the method of titration. Consider the following balanced chemical equations: (1) HCl + NaOH ------> NaCl + HOH (2) H2SO4 + 2NaOH --------> Na2SO4 + 2HOH (3) 2HCl + Ca(OH)2 ---------> CaCl2 + 2HOH (4) H2SO4 + Ca(OH)2 ---------> CaSO4 + 2HOH (5) 2H3PO4 + 3Ca(OH)2 ----------> Ca3(PO4)2
Premium Mole Titration Acetic acid
Introduction: Sodium hydroxides‚ NaOH Is a commonly used titrant for determining the concentration of acidic solutions. We also have guidelines and formulas for achieving and measuring the concentration for example concentration = amount per litre i.e. grams/litre (g/L) or mol/L (M = Molarity) Primary standard and its importance can be justified by its accuracy to find the concentration of a solution‚ in this lab report; we will measure the concentration of NaOH and test our titration method as
Premium Sodium hydroxide Titration
between acids and bases during a titration can be used to determine several characteristics of the acid or the base. Sodium hydroxide was standardized to 0.1035 M in three acid-base titrations of potassium hydrogen phthalate (KHP). This standardized NaOH solution was then used in a series of other titrations with acids in order to gain information about those acids. The first acid tested was hydrochloric acid. This titration showed that the equivalence point occurred at a pH of 7.0. The second acid
Premium Base Sodium hydroxide Acid
Experiment N | Kinetics of the Depolymerization of Diacetone Alcohol via Basic Catalysis | | Ingrid Tafur -5672578 | 2/11/2011 | CHM233O Partner: Laura Marrongelli Demonstrator: Cheryl McDowall Objective The rate constant of the depolymerization of diacetone alcohol via basic catalysis was determined by monitoring the change in volume as a function of time at constant temperature of a pseudo first order reaction where the species in excess was sodium hydroxide. This was accomplished
Premium Rate equation Sodium hydroxide Reaction rate
Determining the Unknown Concentration of NaHCO3 (aq) Through Titration Introduction Titration is the accurate addition of a titrant- solution in a burette- into a measured volume of a sample (Kessel‚ 2003). There are many different types of titration‚ such as acid-base reaction‚ redox reactions‚ precipitation reaction and more (Dohrman). In this lab an acid base titration will be explored. In an acid-base titration‚ the concentration of an acid or base is unknown and is determined by the adding
Premium Chemistry PH indicator Sodium hydroxide
Acid/Base Titrations Pre- Lab Questions 1. Using your textbook or a handbook‚ look up the formula and structure of potassium hydrogen phthalate (KHP) used to standardize the solution of NaOH in this experiment. Calculate the Molar Mass of KHP. Molar Mass= 204.22 g/mol Formula: KC8H5O4 2. Using your textbook or chemical dictionary‚ write the definition of indicator. Indicator- a substance added at the beginning of the titration that changes color at (or very near) the equivalence
Premium Sodium hydroxide Titration Acid