A safety audit for the gas-solid fluidization experiment was conducted. The following safety concerns were found when performing the audit: operating beyond the operating limits‚ spillage of the beads‚ risk of head injury from bending over to change the beads in the apparatus or from the low bar‚ and congestion of the workspace. One of the biggest safety concerns with this lab involved the small glass beads that acted as the solid in the experiment. If the gas flow rate goes below 50 standard cubic
Premium Glass Risk Causality
Part A: Diffusion on a liquid in a liquid. I did an experiment with three different glasses of tap water from the faucet. All three cups measured the same which happened to be 13 cm from the top of the cup to the bottom of the cup. I let the water settle‚ and sit for about an hour so the temperature was the same for all three cups. I then placed one drop of food coloring into the first glass and waited for the coloring to reach the bottom. I calculated 93 seconds. I then went to the second glass
Premium Osmosis Water Diffusion
4-4 Boiling Point Elevation If you dissolve a substance such as ordinary table salt (NaCl) in water‚ the boiling point of the water will increase relative to the boiling point of the pure water. In this assignment‚ you will dissolve a sample of NaCl in water and then measure the boiling point elevation for the solution. 1. Start Virtual ChemLab and select Boiling Point Elevation from the list of assignments. The lab will open in the Calorimetry laboratory with a calorimeter on the lab bench
Premium Gas Pressure Temperature
platform-specific nmap executable and pipes the output back. Zenmap uses Profiles which are basically nmap parameter presets to specify how scans are performed. 3. What step in the hacking attack process uses Zenmap GUI? System Hacking 4. What step in the hacking attack process identifies known vulnerabilities and exploits? Enumeration 5. During the scanning step of the hacking attack process‚ you identified known software vulnerabilities in a Windows XP Professional Workstation
Premium Windows XP Microsoft Windows Operating system
Lab 2 “Separation of a Mixture of Solids Lab Report Assistant (10 points) Data Table 1: Experimental Data Grams Percent of mixture Iron (Fe) fillings 0.9 g 20 % Sand 1.2 g 25 % Table salt 1.6 g 25 % Benzoic acid .8 g 16 % Total 4.5 g 86 & Questions A. How did your proposed Procedures or flow charts at the beginning of this experiment compare to the actual Procedures of this lab exercise? (2 points) I proposed a magnet would be the used to remove the iron from
Premium Water Separation process Distillation
4. Paragraphs 1-4 In User Domain the people are often the weakest link in IT security. In Workstation Domain is vulnerable if not kept up to date. In LAN-to-WAN Domain IP addresses are accessible from anywhere in the world‚ and attackers are constantly probing public IP addresses. They look for vulnerabilities and when one is found‚ they pounce. In Remote Access Domain is vulnerable to authentication because when the user provides credentials to prove identity‚ if found the attacker can later
Premium IP address Risk assessment Computer security
The Molar Mass of a Volatile Liquid Adam Kozdrowicz Adam Li 11/05/12 Mr. McCready Purpose: The purpose of this procedure is to determine the molar mass of an unknown liquid‚ evaporate a sample of a liquid substance‚ and measure certain physical properties of the substance as it condenses. Procedure: 1. Obtain safety goggles. 2. Trim a piece of aluminum foil so that it covers the top of a small 13 x 100 mm test tube. Secure the foil with electrical tape. Make sure
Premium Gas
Community College Staff* Version 42-0207-00-01 Lab RepoRt assistant This document is not meant to be a substitute for a formal laboratory report. The Lab Report Assistant is simply a summary of the experiment’s questions‚ diagrams if needed‚ and data tables that should be addressed in a formal lab report. The intent is to facilitate students’ writing of lab reports by providing this information in an editable
Premium Color Water Sodium chloride
Title: Separation of a Mixture of Solids Purpose: Learn and demonstrate how to separate different ingredients from a mixture of solids using different methods based on the properties of each ingredient. Procedure: I weighed mixture and tools‚ and proceeded to begin separating each ingredient. I used a magnet to separate the iron from the mixture. Then I heated the mixture in water to get the non-soluble sand out. Then I filtered out the benzoic acid after cooling it into a crystal form
Premium Water Evaporation
The Purity and Purification of Solids Melting Point Lab Introduction: The point of this lab was to determine the eutectic point for the naphthalene biphenyl mixture‚ as well as determining the melting point of an unknown substance by comparing it with two known samples. Melting point is a temperature in which a substance changes from solid state to liquid state. Melting points are used to determine whether the given substance is pure or not. Substances that melt sharply‚ less than 1-2°C indicates
Premium Chemical substance Melting point Mixture