Dot Box Research Paper
Dodge Neon SRT-4
N2MB WOT Box Installation Instructions
NOTE: If you have a CDI (capacitive discharge ignition system) please contact us at support@n2mb.com for additional instructions. Damage to your WOT Box can occur if the installation is not completed correctly!
WARNING: Spark‐based rev‐limiters can damage catalytic converters. If you have catalytic converters on your car, N2MB accepts no responsibility for damage caused by the WOT Box.
This being said, many successful installs have been made on Catalytic‐Converter equipped vehicles. Damage usually is only caused by using the launch‐control feature for more than a few seconds, but once again, USE AT YOUR OWN RISK IF YOU HAVE CATALYTIC CONVERTERS!
Please visit our website …show more content…
Verify that the RED and BLACK 16
AWG wires are wired facing the proper way. If they are reversed, the ignition cut will not work.
4. Lastly, test the 2-Step. Press the clutch pedal down and then quickly press the gas pedal all the way down.
The gas pedal must be floored for the 2-step to engage. The engine should rev up to the desired RPM and hold. If it does not, be sure to remove your foot from the gas before you hit the rev limiter. If the 2-step does not work, check the WOT Box YELLOW wire.
CONGRATULATIONS!
These tests verify successful installation of the N2MB WOT BOX.
Usage
To use the WOT Shift feature, keep your foot fully on the gas and shift quickly using the clutch. Keep the gas fully depressed through the shift. The WOT Box will detect the clutch switch signal and briefly cut the ignition to enable an effortless shift.
To use the 2‐Step feature, fully depress the clutch. Next, fully depress the gas pedal to the floor. The engine will rev up and hold the RPM that you have set. Quickly release the clutch while leaving the gas fully …show more content…
Programming
The WOT Box comes preset for an automatic WOT Shift kill time. This means that the WOT Box will automatically adjust the kill time to your shift time, up to a maximum of 350 ms. If you would like manual control over the WOT Shift kill time, start the car and hold down the button on the module and wait for the
LED to begin to blink. Using the chart below, find the number of blinks that corresponds to the desired kill time. Setting 0 blinks will disable the WOT Shift feature and setting 1 blink will set the automatic kill time mode. When you have reached the number of blinks that match your desired setting, simply let go of the button. To confirm, the WOT Box will blink back out the setting you entered.
The WOT Box comes preset for a 2‐step RPM of 4000. To set the 2‐Step RPM, repeat the same procedure described above, but keep the clutch down during the entire operation. This will signify to the WOT Box that you want to set the 2‐step RPM and not the WOT Shift kill time. Use the second chart provided below to match up the desired RPM with the number of blinks. Setting 0 blinks will disable the 2‐Step feature.
Ignition Cut Time Chart ‐ Set with the clutch UP
Blinks
0
1
2
3
4
N2MB WOT Box Installation Instructions
NOTE: If you have a CDI (capacitive discharge ignition system) please contact us at support@n2mb.com for additional instructions. Damage to your WOT Box can occur if the installation is not completed correctly!
WARNING: Spark‐based rev‐limiters can damage catalytic converters. If you have catalytic converters on your car, N2MB accepts no responsibility for damage caused by the WOT Box.
This being said, many successful installs have been made on Catalytic‐Converter equipped vehicles. Damage usually is only caused by using the launch‐control feature for more than a few seconds, but once again, USE AT YOUR OWN RISK IF YOU HAVE CATALYTIC CONVERTERS!
Please visit our website …show more content…
Verify that the RED and BLACK 16
AWG wires are wired facing the proper way. If they are reversed, the ignition cut will not work.
4. Lastly, test the 2-Step. Press the clutch pedal down and then quickly press the gas pedal all the way down.
The gas pedal must be floored for the 2-step to engage. The engine should rev up to the desired RPM and hold. If it does not, be sure to remove your foot from the gas before you hit the rev limiter. If the 2-step does not work, check the WOT Box YELLOW wire.
CONGRATULATIONS!
These tests verify successful installation of the N2MB WOT BOX.
Usage
To use the WOT Shift feature, keep your foot fully on the gas and shift quickly using the clutch. Keep the gas fully depressed through the shift. The WOT Box will detect the clutch switch signal and briefly cut the ignition to enable an effortless shift.
To use the 2‐Step feature, fully depress the clutch. Next, fully depress the gas pedal to the floor. The engine will rev up and hold the RPM that you have set. Quickly release the clutch while leaving the gas fully …show more content…
Programming
The WOT Box comes preset for an automatic WOT Shift kill time. This means that the WOT Box will automatically adjust the kill time to your shift time, up to a maximum of 350 ms. If you would like manual control over the WOT Shift kill time, start the car and hold down the button on the module and wait for the
LED to begin to blink. Using the chart below, find the number of blinks that corresponds to the desired kill time. Setting 0 blinks will disable the WOT Shift feature and setting 1 blink will set the automatic kill time mode. When you have reached the number of blinks that match your desired setting, simply let go of the button. To confirm, the WOT Box will blink back out the setting you entered.
The WOT Box comes preset for a 2‐step RPM of 4000. To set the 2‐Step RPM, repeat the same procedure described above, but keep the clutch down during the entire operation. This will signify to the WOT Box that you want to set the 2‐step RPM and not the WOT Shift kill time. Use the second chart provided below to match up the desired RPM with the number of blinks. Setting 0 blinks will disable the 2‐Step feature.
Ignition Cut Time Chart ‐ Set with the clutch UP
Blinks
0
1
2
3
4