Activity Analysis
I. Preliminary Information
A. Name of activity: Snow Band
B. Components of the task
1. Take a toothpick to combine the two styro balls to create a snowman. Repeat this step for two times.
2. Attach the parts of the snowman (face, guitar, microphone, banner, Christmas tree, gifts and bears) using any kind of sticking solution.
3. Scattered some glue all over the stage of the snowmen then sprinkle some glitters.
4. Insert the four post at the four corners of the stage. Then attached the colored papers around the stage of the snowmen to serve as wall covering.
5. Take any paper that has Christmas-y designs. Then cut out ten circles of desired size.
6. Fold all the circles of paper in half.
7. Stack circles on top of each other, wrap a length of thread all the way around the stack, so it runs along the fold. Tie ends together at top of the stack to secure.
8. Fold and unfold paper sections, so paper starts to fan out.
9. Using a hot glue or school glue, place the glue about 1/3 of the way up to the top of the circle, on the outside edge.
10. Fold the facing flaps together and press to secure the glue.
11. On the next circle, place the glue about 1/3 of the way from the bottom.
12. Continue this all the way around, alternating high and low glue dabs.
13. Knot ends of embroidery thread together to create a hanging loop. Then hang.
14. Lastly, switch on the light placed above the stage using you thumb and index finger by pinching slightly.
C. Steps of activity being analyzed
1. Reach
2. Grasp
3. Release
D. Equipment and supplies necessary
1. Styro foams
2. Glue
3. Designs (guitar, face of a snowman, microphone, colored papers, banner, glitters and bears)
4. Christmas design paper
5. Scissors
6. Embroidery thread or ribbon
E. Environmental Context
The working place for this activity can be done in the OT workshop or any room that is suited to arts and crafts activity. There must be a table and chair for the patient to make the
A. Name of activity: Snow Band
B. Components of the task
1. Take a toothpick to combine the two styro balls to create a snowman. Repeat this step for two times.
2. Attach the parts of the snowman (face, guitar, microphone, banner, Christmas tree, gifts and bears) using any kind of sticking solution.
3. Scattered some glue all over the stage of the snowmen then sprinkle some glitters.
4. Insert the four post at the four corners of the stage. Then attached the colored papers around the stage of the snowmen to serve as wall covering.
5. Take any paper that has Christmas-y designs. Then cut out ten circles of desired size.
6. Fold all the circles of paper in half.
7. Stack circles on top of each other, wrap a length of thread all the way around the stack, so it runs along the fold. Tie ends together at top of the stack to secure.
8. Fold and unfold paper sections, so paper starts to fan out.
9. Using a hot glue or school glue, place the glue about 1/3 of the way up to the top of the circle, on the outside edge.
10. Fold the facing flaps together and press to secure the glue.
11. On the next circle, place the glue about 1/3 of the way from the bottom.
12. Continue this all the way around, alternating high and low glue dabs.
13. Knot ends of embroidery thread together to create a hanging loop. Then hang.
14. Lastly, switch on the light placed above the stage using you thumb and index finger by pinching slightly.
C. Steps of activity being analyzed
1. Reach
2. Grasp
3. Release
D. Equipment and supplies necessary
1. Styro foams
2. Glue
3. Designs (guitar, face of a snowman, microphone, colored papers, banner, glitters and bears)
4. Christmas design paper
5. Scissors
6. Embroidery thread or ribbon
E. Environmental Context
The working place for this activity can be done in the OT workshop or any room that is suited to arts and crafts activity. There must be a table and chair for the patient to make the