Machine Design HES3350 Lecture 2 – Gears Semester 1‚ 2013 1 Learning Objectives • • • • • Familiar with gear nomenclature Able to select a suitable gear type for different applications Able to determine gear train ratios Determine the AGMA bending and contact stress Able to select appropriate gears from supplier’s catalogue 2 Outline • • • • • • • Introduction Gear Nomenclature Gear Ratios Gear Forces Lewis’s Equation AGMA Bending Stress AGMA Contact Stress 3 Introduction
Premium Gear
Topic Outline 1. Introduction (Gear terminologies‚ definitions and identifying the parts) (Identifying the types of gears) (Gear applications or uses) 2. Body (History of gears) (Gear calculations or formula) (Materials for manufacturing gears) 3. Conclusion (Advantages of gears in the industry) (Advantages of gears compare to other drive mechanism) 4. References 5. Thesis Statement: Gears are important in the mechanical fields and industries
Premium Gear
Mayuram Module 2- GEARS Lecture – 11 HELICAL GEARS Contents 11.1 Helical gears – an introduction 11.2 Helical gears – Kinematics 11.3 Helical gears – geometry and nomenclature 11.4 Helical gears – force analysis 11.5 Helical gears – bending stress 11.6 Helical gears – contact stress 11.7 Crossed helical gears 11.7.1 Tips for crossed helical gear design 11.1 HELICAL GEARS – an introduction In spur gears Fig.11.1 dealt earlier‚ the teeth are parallel to the axis whereas in helical gears Fig.11.2 the teeth
Premium Gear
TUTORIAL – GEAR SYSTEMS This work covers elements of the syllabus for the Edexcel module 21722P HNC/D Mechanical Principles OUTCOME 3. On completion of this short tutorial you should be able to do the following. • Describe the different types of gear systems. • Describe a simple gear train. • Describe a compound gear rain. • Describe three types of epicyclic gear boxes • Solve gear box ratios. • Calculate the input and outputs speeds and torques of gear boxes.
Premium Gear Epicyclic gearing Transmission
| Types Of Gears | Gear Type | Description | Photo | Spur Gears | Spur gears are by far the most common type of gear and with the exceptions of the "cog" the type of gear that has been around the longest. Spur gears have teeth that run perpendicular to the face of the gear. | | Helical Gears | Helical gears are very similar to spur gears except the teeth are not perpendicular to the face. The teeth are at an angle to the face giving helical gears more tooth contact in the same area. Helical
Premium Gear Angle
Gear and Gear Trains Mechanical and Mechatronics Engineering Department Faculty of Engineering and Technology Multimedia University of Kenya EMG 2310: Gear Mechanisms Third Year First Semester‚ 2013 BSc. Mechanical Engineering and BSc. Mechatronics Engineering By Dr. Charles M.M. Ondieki August 2013‚ Nairobi Table of Contents 1.0 Gears ....................................................................................................................................... 3 1.1 Advantages and
Premium Gear
Case: Eastern Gear‚ Inc. Q1. (Major problems) * Gears in most orders are small. The exact same gear is rarely ordered more than once. * Some deliveries of small orders are too late because of it took a long time before they were being produced. * Production sometimes has to be stopped because raw materials are not available or the design has still have to be clarified. (orders are not clear enough) * Production time is pretty high and therefore it is difficult to get the orders
Premium Management Gear The Order
Nine NOlES & REFERENCES Module 234-9 THE TURNING GEAR OBJECTIVES: After completing this module you will be able. to: 9.1 a) For each of the turbine operating states listed below‚ state the purpose(s) of the turning gear operation: i) ¢:>Page 2 ii) b) During turbine stanup (2); While shutting down the turbine (I). ¢:>Page 4 For each of the operating states listed in point (a)‚ describe turning gear operation‚ addressing the following points: i) 3 (startup)
Premium Wind turbine Gear Electric motor
The Spur Gear Prepared by: Henry L. Paz Objectives: • • • • To describe the spur gear; To identify the spur gear parts; To draw spur gear; To follow faithfully the steps in drawing a spur gear. Gear up and get ready to learn! Let me ask you. • What is a gear? Gear is… • Toothed wheel used to transmit power and rotating motion from one machine part to another. Gear is… • The simplest form of toothed wheel used in machinery with radial teeth parallel to the axis. Types
Premium Gear Rack and pinion Circle
Worm Gears 12/17/10 12/17-12:19AM Disclaimer: The information on this page has not been checked by an independent person. Use this information at your own risk. ROYMECH Aamco Transmissions Local Independent Nationwide warr. 802-864-0049 Free Estimates www.aamco.com/centerinfo.asp Right Angle Gearbox Spiral Bevel‚ Helical Bevel‚ Worm for PT & Motion Control‚ 1-50 HP www.diequa.com Nordex OnLine Catalog Thousands of Components In Stock Ready to Ship www.nordex.com Home Drive_Index
Premium Gear Friction