PDHonline Course M102 (2 PDH) Selecting a Centrifugal Pump to Handle a Viscous Liquid Instructor: Randall W. Whitesides‚ PE 2012 PDH Online | PDH Center 5272 Meadow Estates Drive Fairfax‚ VA 22030-6658 Phone & Fax: 703-988-0088 www.PDHonline.org www.PDHcenter.com An Approved Continuing Education Provider www.PDHcenter.com PDH Course M102 www.PDHonline.org Selecting a Centrifugal Pump to Handle a Viscous Liquid Copyright © 2002-2011 Randall W. Whitesides‚ P.E.
Premium Viscosity
characteristics of a Centrifugal pump. The Centrifugal pump is largely used in petrochemical industries to move liquids around the plants and refineries. Through common practise of Centrifugal pump operating characteristics is it possible to determine the optimum conditions of particular conditions. The results of typical characteristics are expressed on this work in terms of pump discharge pressure‚ pump efficiency‚ and power demand at various pump speeds of verses pump discharge. The experimental
Premium Fluid dynamics Liquid
TUTORIAL CENTRIFUGAL PUMP SYSTEMS by Jacques Chaurette p. eng. copyright 2005 Fluide Design Inc.‚ 5764 Monkland avenue‚ Suite 311‚ Montreal‚ Quebec‚ Canada H4A 1E9 Tel: 514.484.PUMP (7867) E-mail: jchaurette@fluidedesign.com Web site: www.fluidedesign.com page….2 Table of contents 1. Different types of pump systems 2. Three important characteristics of a pump system: pressure‚ friction and flow 3. What is friction in a pump system 4. Energy and head in pump systems 5. Static head 6. Flow rate
Premium Fluid dynamics Pressure Atmospheric pressure
CENTRIFUGAL PUMP A centrifugal pump converts the input power to kinetic energy in the liquid by accelerating the liquid by a revolving device - an impeller. The most common type is the volute pump. Fluid enters the pump through the eye of the impeller which rotates at high speed. The fluid is accelerated radially outward from the pump chasing. A vacuum is created at the impellers eye that continuously draws more fluid into the pump. The energy created by the pump is kinetic energy according the
Premium Fluid dynamics
E. Reinhart Royce J. Rhoads* Kenneth L. Saucier Paul R. Stodola William X. Sypher* Robert E. Tobin* Kevin Wolf *Member of subcommittee that prepared this report. †Chairman of subcommittee that prepared this report. This report describes pumps for transporting and placing concrete. Rigid and flexible pipelines are discussed and couplings and other accessories described. Recommendations for proportioning pumpable concrete suggest optimum gradation of aggregates; outline water‚ cement‚ and
Premium Concrete Construction aggregate
Centrifugal pump A centrifugal pump is a rotodynamic pump that uses a rotating impeller to increase the pressure of a fluid. Centrifugal pumps are commonly used to move liquids through a piping system. The fluid enters the pump impeller along or near to the rotating axis and is accelerated by the impeller‚ flowing radially outward into a diffuser or volute chamber (casing)‚ from where it exits into the downstream piping system.[1][2] Centrifugal pumps are used for large discharge through smaller
Premium Fluid dynamics
characteristics of the pump‚ comparing the performance characteristics for three different Reynolds numbers and explaining the effects observed and to also make predictions about the performance for a pump with an impeller diameter of 228mm using the data obtained in the experiments. This experiment was conducted under room temperature. The motor was first adjusted to 3000 rpm and the input valve which was used to control the input pressure was adjusted in 0.1bar steps. Pump Inlet and delivery static
Premium Fluid dynamics
No. 1: Heat Pump Experiment 1. Objective The objective of the experiment is to measure the Coefficient of Performance (COP) of a Heat Pump. 2. The experimental setup The equipment provided is a heat pump with pressure and temperature sensors placed at various locations. 3. Procedure Study the diagram and equipment provided and identify the various components of the Heat Pump – that is‚ the compressor (1-2)‚ the condenser (2-3)‚ the expansion valve (3-4) and the evaporator (4-1)
Premium Heat exchanger Heat HVAC
AUTOMATIC WATER PUMP CONTROLLER The automatic water pump controller is used to control the water pump motor. The motor gets automatically switched on when water in the overhead tank (OHT) falls below the lower limit. Similarly‚ it gets switched off when the tank is filled up. Built around only one NAND gate IC (CD4011)‚ the circuit is simple‚ compact and economical. It works off a 12V DC power supply and consumes very little power. The circuit can be divided into two parts: controller circuit and
Premium Temperature
Mabuhay Pumps Company CASE ANALYSIS Introduction Mabuhay Pumps Company has manufactured high quality residential pumps for over 20 years. The firm has always been profitable and relied on home grown talents who have worked with MPC since 15 years ago. The BOD is composed mainly of closed relatives of the founders who have either passed away with a couple of outsiders. Point of View Knowing that MPC is popularly known for their home grown talents‚ quality products‚ and trusted specialization in
Premium Management Business terms Total quality management