The purpose of the Picket Fence Free Fall Lab was to examine the acceleration of objects as they fall to earth. During free-fall the only force that should be acting upon the object is the earth’s gravitational pull (9.8 m/s/s)‚ therefore the velocity of the object should always equal 9.8 m/s/s. In this lab the picket fence was dropped repeatedly through a photogate connected to Logger Pro‚ which allowed the fence’s acceleration and velocity to be recorded and graphed. The results of the experiment
Premium Force Classical mechanics Energy
Purpose of Experiment: The purpose of this experiment of to measure the velocity and acceleration due to gravity of a picket fence and to verify the acceleration due to gravity using the picket fence with Logger Pro and Photogate. Data: Trial # 1 2 3 4 5 6 Slope (m/s^2) 9.80 9.78 9.87 9.77 9.84 9.83 Accel. g (m/sec2) 9.80 9.78 9.87 9.77 9.84 9.83 Minimum Maximum Average Acceleration (m/s^2) 9.77 9.87 9.82 Acceleration due to gravity‚ g 9.82+/- 0.10 m/s^2 Precision 1
Premium Classical mechanics Force Mass
ABSTRACT: The lab of one dimensional motion is a series of experiments that deal with different types of motion in a single direction. In the first experiment‚ one dimensional motion of a small cart on an air track is measured in a one photogate system. The acceleration was calculated by the infrared light emitting electrode of the photogate sensing the slacks on the picket fence. The calculation for gravity yielded 9.63 m/s^2‚ which is consistent with the accepted value of 9.8m/s^2. In the
Premium Velocity Standard deviation Acceleration
LABORATORY REPORT Acceleration Due to Gravity Table of contents Objective 1 Equipment 1 Procedures 1 Recorded data‚ calculated results‚ and graphs 1 Discussion 3 Conclusions 3 Objective In this project we attempted to confirm that the acceleration
Premium Acceleration
Physics Lab Report 1. For the wavelength measurement of different colors in the Hydrogen spectrum done in the lab‚ tabulate your data recorded along with the wavelength calculations performed for all colors in the spectrum. (2 points) Line Color a_left (m) a_right (m) a_average (m) sinq nm Red 0.235 0.27 0.2525 0.182145 5.47E-09 Green-Blue 0.17 0.33 0.25 0.180505 5.42E-09 Indigo 0.16 0.35 0.255 0.18378 5.52E-09 Violet? 0 0 0 0 0 To find the wavelength for all of the colors in this lab we used two
Free Light Color Electromagnetic radiation
Physics Lab report Aammar Paracha Section MX Feb 6th 2015 OPTICS Abstract: This experiment revolves around using light rays and lenses. The experiment also discusses different properties of light rays. This experiment uses different lenses and measurements to produce images and observes different techniques to obtain the image position. Question and Answers: 1. Use your data to verify the Law of Reflection and then use Snell’s Law to calculate
Premium Optics Lens
Grade 11 physics: SPH3U1-01 | Physics Lab Report | Specific Heat Capacity of Brass | | Jin Jin Shi | 2012/12/6 | Instructor: Mr. Nailer | I. Introduction The amount of heat required to raise the temperature of a solid body depends on its change in temperature (ΔT)‚ its mass (m)‚ and an intrinsic characteristic of the material forming the body called specific heat (cp). The heat is calculated from the equation II. Purpose The purpose of this laboratory is to determine
Premium Heat Specific heat capacity Thermodynamics
quantities. Heat is a quantity of thermal energy‚ while temperature determines the direction and rate of heat transfer to the surroundings. It is possible for an object to have a very high temperature but contain very little heat and vice versa (physics 312). When a hot body is mixed with the cold body‚ the hot body cools down and the cold body warms up until the mixture as a whole comes to a common temperature‚ that is‚ in thermal equilibrium. By mixing hot and cold substances and measuring the
Free Thermodynamics Temperature Heat
Name : Siti Zulaikha Binti Dahalan Matric. No : FIS 1307 3296 Name of Partner : Title of Experiment : Experiment 2‚ Uncertainty and Error Date Of Experiment : 1st October 2013 Course Name and Code : Physics Lab 1 (FP1021) Instructor’s name : Dr. Azah Nik Jaafar Objective 1. To measure Human Reaction Time 2. To find uncertainty and error of a measurement Apparatus 1. Ruler Theory Human Reaction Time is a measure of how quickly human can respond to a particular stimulus. This
Premium Measurement
Experiment-5 Thermal physics is the combined study of thermodynamics‚ statistical mechanics‚ and kinetic theory. This practical is done to measure the temperature drop of water over a period of time (30 minutes). Research question- What is the rate of temperature change over a period of 30 minutes? Independent variable- time Dependent variable- the temperature of water Controlled variables- the amount of water in the calorimeter - The stop watch
Premium Temperature Thermodynamics