ampicillin sodium (mg) What weight (in mg) of ampicillin sodium (C16H18N3NaO4S) will provide 144 mg of ampicillin base (C16H19N3O4S)? 27. Weight of potassium permanganate (g) Potassium permanganate is normally made as a concentrated solution which is then diluted prior to use. The concentrated solution is normally made as a 1 in 800 solution. You are asked to supply a patient with sufficient of this solution to allow them to make of use 25 mls of the further diluted solution (1 in
Premium Chemical element Atom Atomic number
Saline Lab Purpose The purpose of this experiment is to find out the molarity of each solution while finding out how many grams of sodium chloride we have. Materials 1. Wire gauze 2. tongs 3. Burner 4. balance 5. Matches 6. hot hands 7. ring stand 8. ring clamp 9. graduated cylinder 10. evaporating dish Procedure Steps: 1. Mass the evaporating dish 2. Record how many mL of solution you add into the evaporating
Premium Water Liquid Solvent
Description Whenever we do experiments‚ the actual result is a little different from the result we predicted. In chemistry‚ this discrepancy is compared by calculating the percent yield. In this lesson‚ we will define percent yield‚ and go over a few examples. !!!What is Percent Yield? Sometimes you look at a recipe and it says how many servings it will make if you follow the amounts listed on there. There are times‚ however‚ that the number of servings after you have made the food is not the
Premium Chemistry Chemical reaction Acid
membrane and goes to the higher concentration of solute.1 2.2. Important factors to Osmosis and Diffusion include Temperature‚ Concentration and Surface area to volume ratio. Temperature can affect the rate in which a solute dissolves in a solution‚ higher temperature faster rate of Osmosis. This is caused by the molecules movements being faster in higher temperatures. Concentrations are important as they affect the movement of solute within a solvent‚ the lower the concentration the faster
Premium Osmosis Concentration Solution
and Standardization of a Sodium Hydroxide Solution Objective/Purpose: The objective of this experiment will be the standardization of sodium hydroxide using potassium hydrogen phthalate by the titration method. Introduction: The concentration of solutions can be reported in terms of molarity and normality. Molarity is equal to: HCL‚ HBR‚ H2SO4‚ HNO3 M = mol Solute (mol) (Monoprotic) (Diprotic) _______________ V(L)g solutions (L) M = __N___
Premium Sodium hydroxide Acid Titration
order to find the formula of the copper chloride hydrate‚ we had to separate the compound to find the mass of water and copper. To begin this process‚ we evaporated the water and created an anhydrous compound‚ meaning we were left with only CuxCly. By calculating the weight of both the anhydrous and the hydrated compounds‚ we could conclude that the difference in the weights was the weight of the H2O. From this we were able to calculate the percent composition of CuxCly and H2O (see Calculations: Part
Premium Chemistry Water Molecule
LAB 12 PERCENTAGE COMPOSITION OF HYDRATES Pre-Lab Questions: See page(s) 1 for calculations Purpose: The purpose of this lab was to learn how to determine the percent of water in a hydrate. Materials: Evaporating dish Ring stand Wire gauze Burner Crucible tongs Triple beam balance Copper(II) sulfate penta-hydrate Spatula Glass stirring rod Distilled water Procedures: See page(s) 1 and 2‚ for procedure steps 1-11 Observations and Data: 1. Mass of evaporating
Premium Water Chemistry Molecule
Sodium From Wikipedia‚ the free encyclopedia This article is about the chemical element. For the PlayStation Home game‚ see Sodium (PlayStation Home). For the racehorse‚ seeSodium (horse). "Natrium" redirects here. For the town in West Virginia‚ see Natrium‚ West Virginia. Sodium 11Na
Premium Sodium Potassium Chemical element
The first step to this experiment is being completely protected from any possible harm that could possibly occur as a consequence of the practical test. Therefore‚ a lab coat‚ safety gloves with clean hands and goggles must be worn before starting the experiment. The initial room temperature should be calculated using a thermometer and a marker is used to name beakers 1 and 2. Divide the 10 test tubes into two groups and name them 1-5 in both groups. 5 different stopwatches are used to record the
Premium
Arroyo Lab report June 11‚ 2013 Biology 123 Professor K Title: Scientific Investigation of the Peroxidase Enzyme & Temperature Abstract: In this lab we tested the effect temperature has on the rate of enzyme activity. The way we figured this out was by taking four different temperatures and testing the different absorbance levels they produced every 20 seconds for two minutes straight using a spectrophotometer. The important part of this experiment was the temperature the enzyme
Premium Enzyme Oxygen Hydrogen peroxide