College Preparatory Academy A mole is a scientific unit developed by chemist that measures large quantities of very small things‚ such as atoms‚ molecules‚ and other particles. There are three types of molar conversions; moles to particles or particles to moles‚ moles to mass or mass to moles‚ and moles to volume or volume to moles. The number of units in a mole is 6.02 × 1023. This number is called Avogadro’s number in honour of Amedeo Avogadro. Full name‚ Lorenzo Romano Amedeo Carlo Avogadro
Premium Albert Einstein Nicolaus Copernicus Galileo Galilei
Angela Pierre Chem 112 Lab Due: 03/05/2015 Lab Report 14 Questions 1. Part A.3. Some of the cyclohexane solvent vaporized during the temperature versus time measurement. Will this loss of cyclohexane result in its freezing point being recorded as too high‚ too low‚ or unaffected? Explain. -The freezing point will be higher because the loss of solvent means that the molarity of solute is too high. The melting point will be lower than expected. 5. Part B.2. The solute dissociates slightly in the
Free Melting point Chemistry Solution
Molar Volume of a Gas – 10/27/08 Alic Albright‚ Josh Coleman‚ Dan Boden‚ Zach Babin Purpose: The pupose of this lab was to make an experimental determination of a molar volume through reaction of the substance shown: Mg(s) + 2HCl(aq) > MgCl(aq) + H(g) Introduction: In this lab‚ a magnesium ribbon and HCl are combined in a gas measuring tube. When they are combined they form magnesium chloride and Hydrogen gas. The molar ratio between Mg reacted and
Premium Gas Chemistry Pressure
Title: 03.09 Molar Mass of Compounds: Determining the Formula of a Hydrate Purpose: To determine the formula of a hydrate. Materials: * crucible * Bunsen burner * balance * CuSO4 hydrate Procedure: 1. Measure the mass of the clean‚ empty crucible‚ record the mass. 2. Add one or two scoops of the hydrate to the crucible‚ record the mass. 3. Heat the crucible and hydrate above a Bunsen burner for at least ten minutes to make sure that all of the water evaporates
Premium Mole Water Addition
Determining the Molar Mass of a Volatile Liquid Purpose: The purpose of this lab was to find the molar mass of a volatile liquid. Data Table: Mass of Test Tube and Stopper (g) | 10.864 g | Barometric Pressure (mmHg) | 749.31 mmHg | Temperature of Boiling Water (C) | 97.1 C | Mass of Test Tube‚ Stopper‚ and Condensed Liquid (g) | 10.890 g | Volume of Flask (mL) | 9.90 mL | Calculations: 749.31 mmHG*1 atm760 mmHg= .98593 atm 9.90 mL*1 L1000 mL= .00990 L 97.1 C+273=370.1 K Substituting
Premium Atmospheric pressure Water Gas
4/9/02 Effects of Salts on the Freezing Point of Water In this experiment‚ you will study the effect that several solutes have on the Freezing Point of water. When a solute is dissolved in a liquid‚ the temperature at which that liquid freezes decreases‚ because the molecules of the solute become attached to the water molecules‚ making it more difficult for the water to form its crystaline shape and form into ice. This process is called Freezing Point Depression. In this experiment‚ you will
Premium Sodium chloride Salt Water
Introduction Molar volume is the name given to the volume that one mole of any gas occupies at standard temperature and pressure. In chemistry‚ many of the materials worked with are gases. It is often easier to measure the volume of a sample of gas‚ rather than determine its mass. The main purpose of this lab is to determine the molar volume of hydrogen gas experimentally in order to compare it to the theoretical molar volume of ideal gases. In this experiment‚ a known mass of magnesium is reacted
Premium Chemistry Gas Pressure
Lab #4 Emission Spectroscopy and Flame Test Date of Lab: 10/24/13 OBJECTIVE To observe a continuous spectrum‚ emission spectrum‚ and an absorption spectrum‚ and be able to distinguish among the three. To be able to identify metal ions by doing a flame test and looking at a spectrum. At the same time increasing the ability to use and understanding of lab equipment‚ in this case‚ a spectroscope. To be able to calculate the frequency and energy of certain frequencies of light. PROCEDURE
Premium Light Incandescent light bulb Spectroscopy
Abstract Molar volume is the volume that one mole of gas occupies when temperature and pressure are kept constant. The molar volume of a gas can be determined through evaluating how much gas is given off when the number of moles of the substance is known. To find the volume of gas that will be used to calculate the molar volume‚ the process of water displacement can be used. Reference Citation Cesa‚ J. (2002). ChemTopic labs: Experiments and demonstrations in chemistry (vol. 9). Batavia
Free Pressure Ideal gas law Mole
Determining the value of molar mass of chosen compound Marta Dürrigl 1mmA Chemical reaction: b.) CaCO3 (s) + 2HCl (aq) ----------- CaCl2 (aq) + CO2 (g) + H2O(l) AIM: The aim of this investigation is to experimentally determine the molar mass of carbon dioxide (CO2) by measuring its volume and calculating its mass. CO2 which we will measure will arise as a product of a chemical reaction between Calcium Carbonate (CaCO3) and Hydrochloric acid (HCl) as it is shown in the chemical
Premium Mass Chemical reaction