Laboratory Report The Plasma Membrane I. Introduction The Plasma membrane is the edge of life‚ the boundary that separates the cell from its surroundings. It controls the traffic of materials in and out of the cell. (Reece‚ 2011). It is incredibly thin that is very vital in maintaining the integrity of the cell. Not only does the plasma membrane bind the other organelles‚ it also forms a dynamic structure which gives them their remarkable activity and selectivity. (Hickman‚ 2008). Diffusion
Premium Osmosis Cell membrane Red blood cell
is the capacitative reactance‚ R is the resistance‚ and ω = 2π f ( f is the linear frequency). Apparatus • PC with DataStudio installed • Science Workshop 750 USB Interface Box • Power Amplifier • Voltage Sensor • AC/DC Electronics Lab Board • LCR meter • Connecting patch cords Experimental Procedure The experimental procedure can be divided into three parts: Part I: Using a Frequency Scan to Determine the Resonance Frequency • The first
Premium Alternating current Inductor Electrical resistance
References: a) http://en.wikipedia.org/wiki/Reynolds_number b) http://www.engineeringtoolbox.com/reynolds-number-d_237.html c) http://www.engineeringtoolbox.com/laminar-transitional-turbulent-flow-d_577.html d) http://www.slashdocs.com/prqt/lab-report-osbourne-reynolds-apparatus.html APPENDIX The Reynolds Apparatus that was used during the experiment.
Premium Fluid dynamics Fluid mechanics Viscosity
The Virtual Lab – ELISA Test Lab: Immunology 09/04/2013 Instructors: Dr. Charlie Wilson Written by: Dipen Patel I. Objective: The purpose of the lab was to learn the procedure of performing an ELISA test to determine whether a particular antibody is present in a patient’s blood sample. ELISA is an abbreviation for “Enzyme-linked Immunosorbent Assay." II. Introduction: The interaction of antigen and antibody outside the body can be used to determine if patient
Premium Antibody Immune system ELISA
List the Earth’s 3 internal layers in the increasing order of their densities? 6. How did the Earth’s 3 internal layers originate? Where did the heat required for the layers to develop come from? 7. Which of the following physical properties of mineral are strongly affected by the mineral’s chemical composition? By the crystal structure? luster‚ streak‚ density‚ hardness‚ crystal form‚ cleavage 8. Define luster‚ streak‚ density‚ hardness‚ crystal form‚ cleavage. 9. Differentiate between: a. Silicates
Premium Plate tectonics Sedimentary rock
McLean 1 Creating Acetylene Gas Introduction The purpose of the lab was to determine the ratio of air to acetylene results in complete combustion of acetylene gas. The balanced chemical equation for this experiment was C2H2(g) + O2(g) --> CO2(g)+ H2O(l). Complete combustion is the reaction of an element or compound with oxygen to produce the most common oxides and energy. Complete combustion occurs when the fuel and oxygen combine in exact proportions to completely burn the fuel
Premium Oxygen Combustion
Investigation Investigate the amount of heat evolved when magnesium reacts with dilute acids. Planning What I am going to do I am going to find out how much heat is given out when magnesium reacts with a variety of dilute acids. In order to make comparisons between the acids‚ I shall use my results to work out how much heat would be given out if 1 mole of magnesium reacted with an excess of each acid. The acids I shall use are hydrochloric acid‚ sulphuric acid‚ nitric acid and ethanoic acid
Premium Hydrogen Sulfuric acid Acid
Example lab report of Synthesis of potassium tris (oxalato) ferrate (III) trihydrate Posted by Nurul Yunaliyana Experiment 5: Synthesis of potassium tris (oxalato) ferrate (III) trihydrate Purpose: to synthesis potassium tris (oxalato) ferrate (III) trihydrate ‚K3 [Fe (C2O4)3].3H2O. Introduction: Ferrous ammonium sulfate‚ Fe(NH4)2(SO4)2.6H2O is dissolved in a slightly acid solution‚ excess oxalic acid‚ H2C2O4‚ is added and the following reaction takes place: Fe(NH4)2(SO4)2.6H2O + H2C3O4
Premium Chemistry Iron Ammonia
One of the main learning experiences of this lab is to learn the importance of calibrating a sensor. In most cases‚ a sensor will not have an output that is exactly what you need. An example of this is a strain gage. A stain gage gives back a voltage‚ but with that given voltage a distance can be found. Introduction: In this experiment‚ the QNET-MECHKIT was used. This board has multiple compact sensors that can be used for experiments. For this lab we will be using the strain gage to find the
Premium Metrology Measurement Angle
I.Purpose The purpose of this lab is to show how potential energy and kinetic energy is shown and transferred using a model rollercoaster. This lab also demonstrates the Law of Conservation of Energy. II.Introduction Potential and Kinetic energy have a very big relationship. The Law of Conservation of Energy states that “Energy cannot be destroyed or created‚ but can be transformed or transferred.” This lab will help demonstrate this law and show the conversion between Kinetic and Potential
Free Energy Potential energy Conservation of energy