NETW230 Quiz 1-7 Week 1: 1. Question : (TCO 1) With _____‚ snap-in gives a single portal to view and administer nearly all information relating to a server’s production health and functionality status. Student Answer: IIS MMC CMD SMP Instructor Explanation: The answer can be found on page 19. Points Received: 5 of 5 Comments: Question 2. Question : (TCO 1) Each _____ has one or more access control entries (ACEs) that state which objects have permissions to the file
Premium IP address Dynamic Host Configuration Protocol Domain Name System
Dynamic Host Configuration Protocol (DHCP) "The Dynamic Host Configuration Protocol (DHCP) is a network protocol used to configure devices that are connected to a network (known as hosts) so they can communicate on that network using the Internet Protocol (IP)." [1] When a computer uses a static IP address‚ it means that the computer is manually configured to use a specific IP address. One problem with static assignment‚ which can result from user error or inattention to detail‚ occurs when two
Premium IP address
3.4.3.1 ZigBee Configuration The basic specifications used in XBee configuration using the free X-CTU software are given below. • Baud rate: 9600 • FC: Hardware • Data bits: 8 • Parity: None • Stop Bits: 1 The PAN ID is configured as 2005 for the network to communicate over. The same ID is given to both the router and the coordinator 3.4.3.1.1 ZigBee Coordinator configuration steps As the X-CTU software is opened‚ the window shown in fig 3.25 appears. The relevant COM port to which the module
Premium IP address Internet Subnetwork
and Internet contact information can remain consistent and constant even if the current Internet routing arrangements change or the participant uses a mobile device. Internet domain names are easier to remember than IP addresses Dynamic Host Configuration Protocol or DHCP for short allows a computer to join an IP-based network without having a pre-configured
Premium Domain Name System Internet IP address
IP and a dynamic IP is that one IP stays the same and the other changes based off of a time limit. A static IP will always remain the same address. A dynamic IP will constantly change. This is beneficial because it slows attempts at unauthorized access to your network. In order for somebody to connect they will need to know the IP address at that current time. For connecting routers in a company there would be no need to implement a dynamic IP. The only IP that I would make dynamic is the default
Premium IP address Network address translation Subnetwork
point) In NAT‚ the ________ creates new external source IP addresses and port numbers. Question 1 options: A) firewall B) source host C) router D) destination host Save Question 2 (1 point) Servers are normally given ________ IP addresses. Question 2 options: A) well-known B) static C) dynamic D) None of these Save Question 3 (1 point) Clients can send a DHCP request message to multiple DHCP servers. Question 3 options:
Free Domain Name System IP address Dynamic Host Configuration Protocol
Lab 2 Packet Tracer Protocol Visualization with Packet Tracer Learning Objectives: 1. 2. 3. Explore Packet Tracer Real-Time Mode and Simulation Mode Explore logical workspace To become familiar with building topologies in Packet Tracer Step 1: Draw the following topology (make sure you are in Real-Time Mode) Figure 1 Step 2: Configure IP Addresses and Subnet Masks on the hosts. Use the following information to configure IP addresses‚ subnet masks and DNS Server Host PC0 PC1 PC2 PC3 IP Address
Premium IP address Web server Dynamic Host Configuration Protocol
a network administrator for a company‚ you want to configure an IP route between two routers. Of static and dynamic routing‚ which is more appropriate? Explain your answer in 200 to 300 words. I think that the best routing choice for this would be a static IP; this is because for a company you may want to have the ability to check the log for problems. Using a dynamic IP would mean that the people that logged on to their device would be almost invisible because they could simply
Premium IP address Subnetwork Dynamic Host Configuration Protocol
and should not be modified. Both host11 and host12 are unable to communicate over this interface. Virtual Machine Login Information Username: vlab Password: password Lab Diagram During your session you will have access to the following lab configuration. Connecting to your lab In this module you will be working on the following equipment to carry out the steps defined in each exercise. WINCONSOLE (Management Server) HOST11 (Linux Server) HOST12 (Linux Server) Each exercise will detail which
Premium IP address Domain Name System Dynamic Host Configuration Protocol
Configuration of HP ProCurve Devices in a Campus Environment Best Practice Document Produced by CESNET led working group on Network monitoring (CBPD111) Authors: Tomas Podermanski‚ Vladimir Zahorik March 2010 © TERENA 2010. All rights reserved. Document No: Version / date: Original language : Original title: Original version / date: Contact: GN3-NA3-T4-CBPD111 March 2010 Czech “Configuration of HP ProCurve Devices in a Campus Environment” Version 1.2 of 3 December 2009 tpoder@cis.vutbr
Premium IP address Ethernet Internet Protocol