deflections of a beam are an engineering concern as they can create an unstable structure if they are large. People don’t want to work in a building in which the floor beams deflect an excessive amount‚ even though it may be in no danger of failing. Consequently‚ limits are often placed upon the allowable deflections of a beam‚ as well as upon the stresses. When loads are applied to a beam their originally straight axes become curved. Displacements from the initial axes are called bending or flexural
Premium Experiment Beam Scientific method
Introduction A bending moment is simply defined as “the algebraic sum of the moments of all the forces which induces bending of an element” (1). The aim of this assignment is to work out the bending moment in a simply supported beam when different concentrated loads are applied to it. A simply supported beam is a structure‚ usually with a straight profile supported at the ends‚ often pinned on one side and simply supported or on a roller on the other. There will be three series of loads applied
Premium Force Torque Bending moment
Institute Physics Course 2014 - Rocket Lab Report Title: RockSim and Electronic Altimeter Measurement Techniques Name: Scarlet Henriquez Email: scarletpatricia94@aol.com LAB SESSION ___8____Assignment _____7_____ Due Date: ___7/8/14______ Objective: Launch a smaller rocket to learn how to compare RockSim predictions (computer based) to an actual instrument measurement carried by the rocket (Electronic Altimeter). This Lab shows how better the electronic measurement
Premium Rocket Mathematics Flight
body which is zero. The ability of the body to rotate in a certain direction is varied according on how much torque is applied. To prove that‚ a beam that is subjected to two forces is balanced by adjusting the perpendicular distances. When applied force is weight‚ modification in masses added is also done. Once equilibrium is achieved‚ or when the beam is not moving at a horizontal position‚ we can calculate for the unknown forces applied through the utilization of this principle. We balance the
Premium Torque Force Mass
Theory of simple bending (assumptions) Material of beam is homogenous and isotropic => constant E in all direction Young’s modulus is constant in compression and tension => to simplify analysis Transverse section which are plane before bending before bending remain plain after bending. => Eliminate effects of strains in other direction (next slide) Beam is initially straight and all longitudinal filaments bend in circular arcs => simplify calculations Radius of curvature is large compared
Premium Elasticity Force Bending
moment with the measured bending moment for a beam under various loads. Introduction and Background Theory Definition of a Beam Members that are slender and support loadings that are applied perpendicular to their longitudinal axis are called beams. Beams are important structural and mechanical elements in engineering. Beams are in general‚ long straight bars having a constant cross-sectional area‚ often classified as to how they are supported. For example‚ a simply supported beam is pinned at one end
Premium Force
Lab Report 3 In this lab‚ we will take a trip to the planetarium lab and will learn about Right ascension and declination‚ and altitude and zenith. After looking at the different points shown‚ we will log the altitude and zenith in the chart in our lab manual. Now we will look at the same points and label the right ascension and declination. Then we will learn about the easiest way to locate the star Polaris. As we started the first program‚ we answered a few questions to make sure we knew
Premium
This lab report will be detailing the steps taken and the results discovered when using spectrophotometry to determine the percentage of copper in a copper-clad penny and the thicknes of the copper layer on the copper-clad penny. After 1982‚ copper coating has been used in the creation of the penny because the cost of pure copper has increase to the point that the amount needed t omake a penny cost far more than the actual value of the penny. This lab allowed us to see just how much copper coating
Premium Chemistry Spectroscopy Ammonia
MEC 325/580 Lab Report CNC Machining Lab Report Date: March 18‚ 2013 Group Leader: Jian Wu Team Members: Group Number: G4 Regment No.: D Insturctor: CONTENTS 1.Objective and introduction. 2.Principles and practice. 3.Design and result. 4.Conclusion and recommendations. Appendices 1. Objective and introduction * Objectives Operate the CNC milling machine using G-codes‚ M-codes in a CNC program. * Equipment: Minitech CNC machine (Series 2) * Machine
Premium Milling machine Numerical control
LAB REPORT Introduction: In a chemical change‚ the identities of substances change and new substances form. In an equation the substances on the left are the reactants. The substances on the right are the products. In this experiment the objectives are to observe evidence that a chemical change has taken place. Infer from observations that a new substance has been formed. Identify and record observations that show energy is involved in chemical change observe the color‚ solubility of some substances
Premium Chemical reaction Chemistry Hydrogen