Purpose The goal of this lab is to find out which metals were used in the minting of pennies before and after 1982 by calculating their densities. Hypothesis If the penny was made after 1982 then its density will be higher than those made before 1982. Materials • 1 Graduated cylinder • 30 mL of water • 10 pennies minted before 1982 • 10 pennies minted after 1982 • 1 electric scale Procedure The mass of ten pennies minted before 1982 was calculated five times using the scale and then
Premium Volume Water Kilogram
Determination of a Rate Law Megan Gilleland 10.11.2012 Dr. Charles J. Horn Abstract: This two part experiment is designed to determine the rate law of the following reaction‚ 2I-(aq) + H2O2(aq) + 2H+I2(aq) + 2H2O(L)‚ and to then determine if a change in temperature has an effect on that rate of this reaction. It was found that the reaction rate=k[I-]^1[H2O2+]^1‚ and the experimental activation energy is 60.62 KJ/mol. Introduction The rate of a chemical reaction often
Premium Chemical reaction Reaction rate Temperature
Lab 34-2: 1. The general trend for bone density as a person ages is a steady decline as years pass. This study shows that every decade‚ males and females bone density slowly decreases. 2. Between the ages of 20-50 females lose about 11% of their bone density and males lose about 13% of their bone density. Males do in fact lose more density then females but they lose it at a more stable and steady rate. Females lose less density at more unstable rate going from about 6% (40-50) to about 9%
Premium Skeletal system Sex Human
Title Page Density Formal Lab Report Name Professors Name Date Purpose/Objective: Determine density of a product for a plastic manufacturing facility. Provide quality control by making sure the physical properties are within design specifications. Density is defined as the ratio of an object’s mass to its volume‚ measured by dividing mass by volume (density = mass/volume). This was accomplished using two different experimental methods‚ displacement and floatation. The theory is that
Premium Density Archimedes Water
Experiment #1: Mass‚ Volume and Density Performed: 2/2/11 Turned in: 2/9/11 The purpose of this experiment is to verify the independence of X and Y motion for a projection. We watch the professor perform this experiment. The equipment used in this experiment was a projectile launcher (ME-6800)‚ a drop shoot accessory (ME-9859)‚ one photogate (ME-9204A)‚ white paper‚ carbon paper‚ two time-of-flight timing pad (ME-6810)‚ two balls (ball 1 and ball 2)‚ and an interface computer. Ball 1 is dropped
Premium Test method Mass Force
Percent Water in a Hydrate PURPOSE To determine the percent water in a hydrate sample. INTRODUCTION Many substances contain water molecules as a part of their crystal structure. We call such solids hydrates‚ and we call the bound water the water of hydration. A hydrate has a definite number of water molecules bound to each anhydrous salt unit. The formula of the hydrate copper(II) sulfate pentahydrate is CuSO4 · 5 H2O The dot indicates that the molecules of water are attached to the ions in
Premium Molecule Water Chemistry
Enhanced spectrofluorimetric determination of Mebendazole‚ a benzimidazole anthelmintic drug‚ through complex formation with Lanthanum (III)‚ in pharmaceutical preparations and spiked human plasma Abstract The article concerned with the development of simple‚ sensitive‚ rapid and specific spectrofluorimetric procedure for determination of mebendazole. The cited drug was reacted with lanthanum (III) ions to produce highly fluorescent stable complex measured at 340 nm after excitation at 295 nm. Different
Premium Chemistry Solvent Acetic acid
Soil Porosity & Density Objective: To determine if the porosity of soil is related to the density. Hypothesis: I think that that the porosity of soil is related to the density because the higher the density of the sand the lower the porosity of the sand‚ which are both componets for the water to rise. Materials: • Sand and Loam samples • 2 large containers • Plastic cups • Water • Scale Procedure: Loam 1) The loam without the water was fresh ‚ it had different shades of black‚ and
Premium Soil Density Sand
Name Date Lab: Denisty – Solids and Liquids Part 1: Density Background Information: The density of an object is how much “stuff”‚ or molecules‚ a substance is made of. Density is how tightly packed the molecules are. To calculate the density of a substance we need to know the mass (weight) of the substance and the volume (how much space) of the substance. Mass is determined by weighing an object. Volume of regular shaped objects is calculated by measuring
Premium Density Kilogram Volume
<center><b>Mass‚ Volume‚ and Density Lab</b></center> <br>The purpose of this lab was is to find the mass and volume of an object. Then to find the density of the object using the measurements of the mass and volume. <br> <br><b>Equipment:</b> <br>scale <br>graduated cylinder <br> <br><b>Hazards:</b> <br>dropping object into graduated cylinder too fast may cause it to break <br> <br><b>Procedure:</b> <br>First get out the equipment that will be needed. Make sure to have about 5 objects that can fit
Premium Length Volume Mass