EXPERIMENT-1 DENSITY OF LIQUIDS PREPARED BY BURAK COBAN PURPOSE: In this experiment we will learn how can we find the density of liquids and liquids of density how change effect of temperature‚ pressure‚ mass‚ volume and concentration. For this reason we will take NaCI solutions with different concentrations and we will measure their densities‚ so we will find out the effects of concentration on density of solutions. THEORY: Density is a physical property
Premium Density Liquid Volume
Determination of g by Free Fall Raw Data: Time (ms) ± 0.01ms Height of release of ball from the sensor plate (cm) ±0.1cm Trial 1 Trial 2 Trial 3 Trial 4 Trial 5 0.0 0.00 0.00 0.00 0.00 0.00 15.0 180.05 179.36 178.74 180.26 180.23 30.0 244.33 244.21 244.71 243.88 245.87 45.0 300.72 301.29 300.59 301.43 301.70 60.0 348.68 348.39 348.77 349.12 348.35 75.0 390.27 390.77 389.58 391.19 390.43 This table below is the results obtained during the experiment in cm/ms. This table below is the results
Premium Measurement Numerical analysis Standard deviation
Solubility Product Determination Purpose • To determine the solubility product constant‚ Ksp‚ of an ionic compound. Introduction The solubility product constant‚ Ksp‚ is a particular type of equilibrium constant. The equilibrium is formed when an ionic solid dissolves in water to form a saturated solution. The equilibrium exists between the aqueous ions and the undissolved solid. A saturated solution contains the maximum concentration of ions of the substance that can dissolve at
Premium Chemistry Solution Solubility
PRE-LAB REPORT Lab: Density of Liquids and Solids Purpose of the experiment: The purpose of this lab is to help understand how to resolve the density of liquids and solids. Also‚ the lab is supposed to teach us how to record lab data and how to measure volume and mass the correct way. Lastly‚ it’s designed to help us understand significant values and its relationship to measurements and data recording. Lab Techniques: One technique that will be used during this lab is comparing the
Premium Density Volume
UNKNOWN SAMPLE #97 COMPLEXOMETRIC DETERMINATION OF WATER HARDNESS DR. BUDRUK CHM 152 LL SEAN MARKIS 4 FEBRUARY 2015 Introduction Using a Lewis base neutral molecule to donate electron pairs (ligands) to a Lewis acid metal ion center to form a single cluster (complex) ion. When the complex ions forms with a metal ion (chelation) the ligand used is called the (chelating agent). EDTA acts as a great chelating agent due to the Nitrogen and Oxygen donating an electron pair to the
Premium Water Calcium Titration
DETERMINATION OF BOILING POINTS Introduction: The boiling point of a compound is the temperature at which it changes from a liquid to a gas. This is a physical property often used to identify substances or to check the purity of the compound. It is difficult‚ though‚ to find a boiling point. Usually‚ chemists can only obtain a boiling range of a 2 - 3oC accuracy. This is usually sufficient for most uses of the boiling point. Purpose: The purpose of this experiment is to determine the
Free Gas Temperature Water
Value density/ packaging density IBMS 203 Huang Yang 0842317 Value density is defined as the value of a good per pound of weight. For example‚ the value of a pound of diamond which is much higher than the value of a pound of bananas. That is the value density‚ two goods have same size and same weight‚ but they have different values. It is used to determine a product where should be stored and how can it shipped. It can show how important of transportation cost in the total product
Premium Kilogram Price Costs
Determination of a Rate Law Megan Gilleland 10.11.2012 Dr. Charles J. Horn Abstract: This two part experiment is designed to determine the rate law of the following reaction‚ 2I-(aq) + H2O2(aq) + 2H+I2(aq) + 2H2O(L)‚ and to then determine if a change in temperature has an effect on that rate of this reaction. It was found that the reaction rate=k[I-]^1[H2O2+]^1‚ and the experimental activation energy is 60.62 KJ/mol. Introduction The rate of a chemical reaction often
Premium Chemical reaction Reaction rate Temperature
Experiment 4A: Determination of a Partition Coefficient for Benzoic Acid in Methylene Chloride and Water Experiment 4B: Solvent Extraction I: Acid-Base Extraction Using the System Benzoic Acid‚ Methylene Chloride‚ and Sodium Bicarbonate Solution Objective A: To accustom participants (students) to general procedures that are used to obtain a partition coefficient at the microscale level. We will gain experience in such practices as the transfer of microliter volumes of solutions with a Pasteur filter
Premium Solvent Sodium bicarbonate Solubility
Performed: July 10‚ 2013 Group No.: 4 Date Submitted: July 17‚ 2013 Experiment #1: Measurements INTRODUCTION Density is a physical property of matter‚ as each element and compound has a unique density associated with it. The unit of Density is g/cm3 or g/mL. It is used to measure thr relative “heaviness” of objects with a constant volume. As defined‚ the formula for Density is Mass over Volume (ρ=m/v) and it can be rearranged to get the Volume (v=m/ρ) or Mass (m=ρv) of a certain substance
Premium Density Volume Water