Abstract The purpose of this experiment was to identify whether density is an extensive or intensive physical property. By using water displacement‚ the volumes of the paper clip samples were measured and the masses were obtained by using an electronic balance. Each mass and volume was unique to their sample so by using their values‚ density was used to identify substances in the lab. After conducting the experiment‚ the results showed that there was a positive slope between the different paper
Premium Temperature Physical quantities Density
The Density Challenge: A Complete Inquiry Activity Introduction Density has been an important part of science for a very long time. Density was discovered by Archimedes‚ a Greek mathematician‚ around 250 BC while determining whether a craftsman had replaced some of the gold in the King of Syracuse’s crown with silver. Density is the compactness of a substance. The new concept of density he discovered was used to expose the fraud. The purpose of this experiment is to make
Premium Density Volume Water
I. Introduction A. Purpose The purpose of this lab was to practice measuring the mass and volume of different samples and to calculate the density and specific gravity of those samples using the measurements. B. Equipment 1. Electronic balance- The electronic balance is a device used to measure the exact mass of an object 2. Graduated cylinder- The graduated cylinder is a tool used to measure the volume of a liquid 3. Pipets- Pipets are small tubes that suck up and contain liquids C. Technique
Premium Chemistry Water Test method
DENSITY OF LIQUIDS AND SOLIDS by Lab instructor: Due date: Results and discussion: The purpose of the experiment was to determine the densities of the unknown liquid and solid as precisely and accurately as possible in order to identify them. It was carried out first on distilled water in order to rule out systematic errors. A 10 mL beaker was placed on a top pan balance and “tared”. The beaker was then removed and 10 mL of distilled water was pipetted into it before it was placed
Premium Water Chemistry Volume
1. DATA: Table 1: Density based on dimensional analysis Trial 1 Trial 2 Trial 3 Units Mass of sample 70.5466 70.5467 70.5465 g Dimensions of sample Length 4.98 4.98 4.99 cm Width 1.21 1.22 1.21 cm Height 1.21 1.22 1.22 cm Volum of sample 7.29 7.41 7.37 cm^3 Density of sample (based on dimensional analysis) 9.68 9.52 9.57 g/cm^3 Table 2: Density based on the displacement of water Trial 1 Trial 2 Trial 3 Units Mass of sample 70.5467 70.5465 70.5466 g Final
Premium Density Volume Water
DENISTY LAB 2/25/13 Chemistry H. Mrs. Halme Objective: Your task is to determine the density of 3 known metals: Zinc‚ Copper‚ and Lead. They are each marked. You must then calculate the density of an unknown metal and determine its identity based on your data from your known samples. Reagents: None Equipment: Lead Copper Zinc Triple Beam Balance Graduated cylinder Unknown metal (Magnesium) Beaker Calculator Procedures Preparation: We observed the given equipment
Free Calculator Mathematics Division
Lab No.1: density‚ accuracy and precision Aim: to determine the relative precision and accuracy of different glassware items by calculating the density of a known substance. Introduction: the density of a substance is its mass per unit volume. (where P-density‚ m- mass and v- volume). Different materials usually have different densities and densities vary according to the pressure‚ temperature and purity of a substance. When measuring‚ there is always a small uncertainty or error and therefore
Premium Management Scientific method Education
CHM 3120L ANALYTICAL CHEMISTRY I LABORATORY REPORT EXPERIMENT: SPECTROPHOTOMETRIC DETERMINATION OF IRON IN DRINKING WATER Name: Steven Adrien Section: 3 Date Experiment Completed: Wednesday‚ July 17‚ 2013 1. Complete the following table Fe(II) stock solution | mass‚ g | 0.1756 | volume‚ mL | 500.0 | MW(Fe(NH4)2(SO4)2 x 6H2O)‚ g/mol | 392.14 | AW(Fe)‚ g/mol | 55.85 | conc. Fe(II)‚ ppm | 50.0 | Use Equation Editor to show how you calculated the concentration of Fe(II)
Free Chemistry
Measurement of the Densities of Water and Alcohol Phuc Truong and Shane Steele Data Collected: September 8‚ 2014 2:05 P.M. Purpose: The purpose of the experiment is to measure the densities of liquids. Specifically‚ the two liquids that were used and measured in the research were deionized water (H2O) and alcohol (C2H5OH). Methods: Density is an intensive quantity that cannot be visually identified. Therefore‚ the most straightforward approach to this problem was to record the measurements of mass
Premium Water Volume Density
The density of fractions 1‚ 2‚ and 3 are as follows: 1.49‚ 1.325‚ and 1.34 g/mL. These values areincorrect because the density should not have been over 1.0 g/mL. This is because the density of water is 1.0 g/mL‚ and the product should have had a mixture of ethanol and water‚ making the density lower. The measured weight of the vials and ethanol were incorrect due the scales.There are many factors that can cause a scale not to read the correct value. The first is the airflow underneath the weighing
Premium Density Volume Water