UNIVERSITY BELGAUM A report on WATER JET MACHINING Submitted By CHAITRA KUMARI A B Under The Guidance of Lecturer Department of Industrial and Production Engineering SJCE‚ Mysore DEPARTMENT OF INDUSTRIAL AND PRODUCTION ENGINEERING SRI JAYACHAMARAJENDRA COLLEGE OF ENGINEERING AUTONOMOUS‚ MYSORE ABSTRACT Abrasive water jet machining is classified as a non-conventional machining process. Abrasive water jet machining uses water jet under high pressure as a tool‚ with
Premium Water jet cutter Water
pkray@nitrkl.ac.in ’R~prttited irom the journai of the Institution of Bnglneers~)vbt (; ’3‚pt. m 3‚ Novenibert~82 ’ ’ UDC 621-16/-17:621/621.9 Water Jet Machining-A State of Art P K Ray‚ Associate Member With the advent of newer materials and intricate shapes of components‚ unconventional methods ofmatflrial removal have been developed. Water jet machining (WJM) is cne ( ’f such processes of material removal. This paper briefly describes the basicfcatures of WJM‚ such as‚ its mechanism of material
Premium Water jet cutter Water
accuracy can be easily achieved. Among them‚ Abrasive Water Jet cutting proves to be a promising area since there is no possibility of thermal damage to the material. AWJ cutting belongs to the mechanical group of non-conventional techniques which uses the mechanical energy of water and abrasives to perform the material removal process. Water is pumped at a high pressure and abrasive is added to the stream in such a way that the momentum of water stream is transferred to the abrasives. Hence‚ the abrasive
Premium Machining Composite material Water
generated by impact of the jet on vanes of various shapes like flat plate‚ conical cup and hemispherical cup. Besides that‚ the results from the experiment have to be compared with the theoretical calculations too. 1.0 Introduction Water turbines are widely used throughout the world to generate power. By allowing fluid under pressure to strike the vanes of a turbine wheel‚ mechanical work can be produced. Rotational motion is then produced by the force generated as the jet strikes the vanes. One
Premium Mass Fluid dynamics Mass flow rate
IMPACT OF a jet ABSTRACT The objective of this experiment is to determine the force exerted by a jet of water on vanes of various shape.Three different shape of vanes;flat plate‚conical cup‚and hemispherical cup are used for this experiment.The results obtain from the experiment are then used to compare with the theoretical results.Force generated on the surface of vane depends on the rate of change of momentum and it can be calculated by recording the time taken for water to reach a certain
Premium Mass Water jet cutter Force
Impact of A Jet Philip Mah Koon Yue Mohananda a/l Anantha Krishnan Ahmad Saeed Abood Eleanor Hang Lee Shean Chan Jun Hoe School of Engineering Taylor’s University Malaysia 23 March 2011 Table of Content Abstract 3 1. Introduction 3 2. Experiment Design 3 2.1 Materials 3 2.2 Methods & Procedures 4 3. Results and discussion 5 4. Conclusion and Recommendations 8 References 8 Appendix 9 Abstract The experiment was conducted to find the impact of water on different types of
Premium Mass Water jet cutter Force
ABRASIVE JET MACHINING INTRODUCTION:- IT IS A PROCESS OF MATERIAL REMOVAL THROUGH THE ACTION OF A FOCUSED STREAM OF FLUID WITH ABRASIVE PARTICLES. IT IS ESPECIALLY USED FOR MACHINING SUPER ALLOYS‚ CERAMICS; GLASS AND REFRACTORY MATERIAL. IT IS ONE OF THE NON-POLLUTING METHODS AVAILABLE FOR MACHINING HARD MATERIALS TO PRECISION DETAILS. IN ABRASIVE WATER JET MACHINING THE ABRASIVE PARTICLES UTILIZES WATER JETS TO ACCELERATE OR DECELERATE THEIR SPEEDS DEPENDING UPON THE TYPE OF MATERIAL TO BE MACHINED
Premium Machining Water jet cutter Water
internal strengths to ensure they are able to maintain their position in the industry. A SWOT analysis can be viewed in Exhibit 1. Adamac currently has over 70 clients and is operating at full capacity. Adamacs’ laser cutter machine broke down 6 times last year‚ and the water jet machine broke down 5 times. The total cost of outsourcing this work was $10‚500‚ the cost breakdown can be view in Exhibit 2. Quality control of their product is a
Premium Water jet cutter Water Customer service
bullen-ultrasonics.com/UltraMachine.html 2. Cogun‚ C. (2010). A new method for machining electrically nonconductive workpieces using electric discharge machining technique. 3. michael‚ K. (1987). “method and apparatus for forming a high velocity liquid abrasive jet.
Premium Water jet cutter Water Energy
Module 9 Non conventional Machining Version 2 ME‚ IIT Kharagpur Lesson 37 Water Jet and Abrasive Water Jet Machining Version 2 ME‚ IIT Kharagpur Instructional Objectives o o o o o o o o o o o o o List four different non conventional machining processes Differentiate between water and abrasive water jet machining List different WJM and AWJM systems List ten different modules of AWJM systems List four applications of AWJM List three advantages of AWJM List materials that can be processed
Premium Water Machining Water jet cutter