Institute Physics Course 2014 - Rocket Lab Report Title: RockSim and Electronic Altimeter Measurement Techniques Name: Scarlet Henriquez Email: scarletpatricia94@aol.com LAB SESSION ___8____Assignment _____7_____ Due Date: ___7/8/14______ Objective: Launch a smaller rocket to learn how to compare RockSim predictions (computer based) to an actual instrument measurement carried by the rocket (Electronic Altimeter). This Lab shows how better the electronic measurement
Premium Rocket Mathematics Flight
EXPERIMENT 1: TITLE: ISOMERISM AND KINETICS IN COORDINATION CHEMISTRY OBJECTIVE: 1. To prepare and study the kinetics of the interconversion of some of the isomers of a typical coordination compound. INTRODUCTION: Isomerism played a central role to establish the basic concept in coordination chemistry while reaction kinetics of coordination compound is known as the area of continuing intense research activity. The mechanism of the reactions of coordination compounds relevance
Premium Chlorine Hydrochloric acid Solvent
tubes * Put 2mL of 40% NaOH solution to test tubes 1‚ 2 and 3 and on test tubes 4 and 5‚ put 10% NaOH solution * Add 10 drops of the following solution: * Tube 1: formaldehyde * Tube 2: benzaldehyde * Tube 3: acetaldehyde * Tube 4: acetaldehyde * Tube 5: acetone * Transfer all test tubes in a boiling water bath for 10 minutes * Record all observations Results: Sample | NaOH | Observations | 1. Formaldehyde | 40% NaOH | Alcohol-like odor |
Premium Aldehyde Alcohol Carbonyl
Lab Report 3 In this lab‚ we will take a trip to the planetarium lab and will learn about Right ascension and declination‚ and altitude and zenith. After looking at the different points shown‚ we will log the altitude and zenith in the chart in our lab manual. Now we will look at the same points and label the right ascension and declination. Then we will learn about the easiest way to locate the star Polaris. As we started the first program‚ we answered a few questions to make sure we knew
Premium
Introductory Biology 1 Biology 1003 Fall Term 2011 Lab Number: 3 Title: Cell Energetics: Enzyme Role in Biological Reactions Name: Brandon Moore Student Number: 100819124 Lab day and time: Wednesday pm Date: Wednesday November 23‚ 2011 Introduction Enzymes are a key aspect in our everyday life and are a key to sustaining life. They are biological catalysts that help speed up the rate of reactions. They do this by lowering the activation energy of chemical reactions (Biology
Premium Chemical reaction Enzyme
This lab report will be detailing the steps taken and the results discovered when using spectrophotometry to determine the percentage of copper in a copper-clad penny and the thicknes of the copper layer on the copper-clad penny. After 1982‚ copper coating has been used in the creation of the penny because the cost of pure copper has increase to the point that the amount needed t omake a penny cost far more than the actual value of the penny. This lab allowed us to see just how much copper coating
Premium Chemistry Spectroscopy Ammonia
Bases: Reactions‚ Standardizations‚ & Titrations Experiments 21 & 22 Experimental Overview: The procedure for this experiment was carried out as instructed in the laboratory manual‚ Experiments in General Chemistry‚ 4th ed.‚ S.L. Murov‚ Experiment 21‚ Acids and Bases: Reactions and Standardizations‚ and Experiment 22‚ Acids and Bases: Analysis. There were modifications made by the instructor to dilute the 6M NaOH to 0.1M in 300mls instead
Premium Chemistry Acid Sodium hydroxide
Condensation Revised Procedure http://www.xula.edu/chemistry/documents/orgleclab/23Aldol.pdf 2. Aldol Condensation Notes http://www.xula.edu/chemistry/documents/orgleclab/Aldol_notes.pdf Data and Observations: Volume of Ethanol: 4.1 mL Volume of NaOH: 4.2 mL Volume of Benzaldehyde: 2.0 mL Total Crude Mass: 3.082g Total Recrystallized Product Mass: 0.863g Crude Percent Yield: 67% Recrystallized Percent Yield: 18.7% Crude Melting Point Range: 53°-96°C Recrystallized Product Melting Point
Premium Chemical reaction Aldehyde Acetic acid
MEC 325/580 Lab Report CNC Machining Lab Report Date: March 18‚ 2013 Group Leader: Jian Wu Team Members: Group Number: G4 Regment No.: D Insturctor: CONTENTS 1.Objective and introduction. 2.Principles and practice. 3.Design and result. 4.Conclusion and recommendations. Appendices 1. Objective and introduction * Objectives Operate the CNC milling machine using G-codes‚ M-codes in a CNC program. * Equipment: Minitech CNC machine (Series 2) * Machine
Premium Milling machine Numerical control
the period of oscillations to the length of the pendulum.Sources of error for this procedure included precision in both length and time measurement tools‚ reaction time of the stopwatch holder‚ and the accuracy of the stopwatch with respect to the lab atomic clock. The final result of g takes into account the correction for the error introduced using the approximation. There are opportunities to correct for the effects of mass distribution‚ air buoyancy and damping‚ and string stretching[1]. Our results
Premium Regression analysis Measurement Normal distribution