generated from flows of electrons between the two metals in the metal sulfate solution of the electrolyte. In order for a chemical reaction to take place‚ the reactants must collide. The collision between the molecules in a chemical reaction provides the kinetic energy needed to break the necessary bonds so that new bonds can be formed. Thus‚ increasing the concentration of the anode‚ zinc sulfate‚ will increases the rate of reaction for oxidation because there are more zinc ions in the new concentration
Premium Electrochemistry Electrolysis Battery
Standardization of hydrochloric acid by sodium carbonate Concentrated hydrochloric acid is roughly 11 M. Pour out into a measuring cylinder about 2 cm3 of concentrated hydrochloric acid. Transfer it to a 250 cm3 flask and make up to the mark with water. Shake well. Put some pure sodium hydrogen carbonate or anhydrous sodium carbonate into an evaporating dish and heat gently over a low flame for about fifteen minutes‚ stirring continuously. Take care not to heat the mass too strongly or fusion
Premium Sodium carbonate Carbon dioxide Sodium bicarbonate
Acid Attack 4 women in their early 20s were attacked by a 41 year old mentally unstable woman. On September 18‚ 2017 there was an acid attack at the train station in Marseilles. ( Which is in southern France). The women that were attacked by acid are Courtney Siverling‚ Charlotte Kaufman‚ Kelsey Kosten‚ and Michelle Krug. The kind of acid that was used was hydrochloric acid. The hydrochloric acid was brought in a DIY store and was sprayed form a spray canister. They were attacked by a mentally
Premium Abuse Mental disorder Salem witch trials
Finding the Activation Energy of the reaction between Hydrochloric Acid and Sodium Thiosulfate The equation for the reaction is: S2O32- (aq) + 2H+(aq) ⋄ SO2 (g) + S(s) + H2O (l) Equipment - 2 boiling tubes - 400 cm3 beakers - Marker pen - Stand and clamp - Timer - Bunsen burner‚ tripod and gauze - 0 – 100 oC thermometer - 2 x 10 cm3 measuring cylinders - Access to a fume cupboard. Method 1. Label two boiling tubes A and B. Mark a dark spot on the side of a 400cm3 beaker‚ then ½ fill
Premium Temperature Measurement Energy
Hydroxide (NaOH) by titrating it with Hydrochloric Acid (HCl) and to identify any possible sources of error. A colour change from pink to yellow signified the end of each individual titre as the NaOH had been neutralised. Experimental: Method: Firstly two solutions were prepared to show the colour of the Phenol Red indicator in acid and alkaline conditions. These colours were then used to determine the end point of each titre. In the experiment 0.100M HCl (acid) was added‚ from a burette‚ to a solution
Premium Sodium hydroxide Chemistry Base
Investigation How does the concentration of the sodium thiosulfate affect the rate of reaction to hydrochloric acid? contents page 1: contents‚ aim‚ prediction‚ equation‚ diagram page 2: equipment‚ preliminary experiments page 3: page 4: page 5: page 6: page 7: page 8: Aim: In my investigation I am trying to find out how the rate of reaction between sodium thiosulfate and hydrochloric acid gets affected but the concentration of the thiosulfate. Prediction: My prediction is that the increased
Premium Chemical reaction Reaction rate Chemistry
Factors affecting the rate of reaction between a metal and an acid The rate of a reaction can be measured by the rate at which a reactant is used up‚ or the rate at which a product is formed. The temperature‚ concentration‚ pressure of reacting gases‚ surface area of reacting solids‚ and the use of catalysts‚ are all factors which affect the rate of a reaction. Individual properties of substances also affect reaction rates. The scope of these properties is broad and there are few generalizations
Premium Oxygen Chemical reaction Base
of Marble chips and Hydrochloric acid Aim: We will measure the loss in mass of the marble chips (CaCO 3 ) as it reacts with Hydrochloric acid (HCl). This one method of measuring the rate of reaction. We will use a balance to measure this mass loss as the reactants are used up to form product. Safety: * As Hydrochloric acid is corrosive wear a lab coat‚ gloves and safety goggles. * Take care when using the glassware not to cut yourself. * When the reaction is taking place Carbon
Premium Calcium carbonate Chlorine Hydrogen
Description of the experiment * Aim: To observe the reactions of sulfuric acid as an oxidising agent and as a dehydrating agent. Equipment: * 20mL of concentrated sulfuric acid * 20mL of 2mol/L sulfuric acid * 2 small pieces of each of copper‚ zinc and iron * Sandpaper * 10 test tubes * Test tube rack * 2g of sugar crystals (sucrose) * 2 wooden ice-cream sticks * 10mL measuring cylinders Steps: A: Sulfuric acid as an oxidising agent 1. Clean pieces of metal
Premium Sulfuric acid Sulfur Hydrogen sulfide
Experiment 6 Preparation and reactions of boric acid Objectives: To prepare boric acid from sodium tetraborate (borax) To carry out tests on the prepared sample of boric acid To study the physical and chemical properties of boric acid Introduction: Boron is an element in the p-block of the periodic table. It has the electron configuration of 1s22s22p1 and is in group 3 or goup 13 (IUPAC classification). In nature‚ it consists of two isotopes 10B (19.6%) and 11B (80.4%). Boron is bonded
Premium Hydrochloric acid Sulfuric acid PH