Institute Physics Course 2014 - Rocket Lab Report Title: RockSim and Electronic Altimeter Measurement Techniques Name: Scarlet Henriquez Email: scarletpatricia94@aol.com LAB SESSION ___8____Assignment _____7_____ Due Date: ___7/8/14______ Objective: Launch a smaller rocket to learn how to compare RockSim predictions (computer based) to an actual instrument measurement carried by the rocket (Electronic Altimeter). This Lab shows how better the electronic measurement
Premium Rocket Mathematics Flight
title: Extraction of Bacteria Plasmid DNA and Analysis of extracted DNA Samples Objectives: 1) To study and understand the steps for extract bacteria plasmid DNA. 2) To measure the concentration and purity of extracted DNA by using spectrometric method and agarose gel electrophoresis method. 3) Determine the size of extracted DNA by using agarose gel electrophoresis method. Materials and Methods: (Refer to UDEE2124 lab manual from page 7 to page 10)
Premium Bacteria Molecular biology Protein
Lab Report: Toothpickase and Enzymes September 19‚ 2012 Olivia DePhillips Lab Partner: Joy Morgan Meyers Signature: Introduction Enzymes are biological molecules that catalyze chemical reactions. In enzymatic reactions‚ the molecules at the beginning of the process‚ called substrates‚ are converted into different molecules‚ called products. Almost all chemical reactions in a biological cell need enzymes in order to occur at rates sufficient for life. Like all catalysts‚ enzymes work
Premium Enzyme Chemical reaction Catalysis
onto it was firstly amplified by PCR‚ then cloned in the pBluescript plasmid vector. EZH2 is an enzyme which adds methyl groups to the twenty seventh amino acid (Lysine) and is encoded by EZH2‚ the EZH2 gene encodes part of the Polycomb group which make protein complexes that help to maintain genes transcriptional repressive state over successive cell generations. http://www.ncbi.nlm.nih.gov/gene/2146 Throughout this lab report template DNA that contains the gene EZH2 was provided‚ this will be
Premium DNA Gene Protein
GRAVIMETRIC ANALYSIS OF A CHLORIDE SALT Report Submitted by: Ronald Milner Laboratory partner: Kiesha Mantik Lab Performed: February 16th‚ 2012 Group: Thursday Afternoon‚ Group F Date submitted: March 14th‚ 2012 Purpose: To determine the chloride content of an unknown soluble salt while illustrating the techniques involved in gravimetric analysis. Theory: In order to find the chloride content of an unknown soluble salt‚ that chloride can first be extracted from the
Premium Chemistry Solubility Water
Lab Report 3 In this lab‚ we will take a trip to the planetarium lab and will learn about Right ascension and declination‚ and altitude and zenith. After looking at the different points shown‚ we will log the altitude and zenith in the chart in our lab manual. Now we will look at the same points and label the right ascension and declination. Then we will learn about the easiest way to locate the star Polaris. As we started the first program‚ we answered a few questions to make sure we knew
Premium
This lab report will be detailing the steps taken and the results discovered when using spectrophotometry to determine the percentage of copper in a copper-clad penny and the thicknes of the copper layer on the copper-clad penny. After 1982‚ copper coating has been used in the creation of the penny because the cost of pure copper has increase to the point that the amount needed t omake a penny cost far more than the actual value of the penny. This lab allowed us to see just how much copper coating
Premium Chemistry Spectroscopy Ammonia
Sample Short Lab Report By Charles M Borener Jr April 24‚ 2009 Kinetic Friction Experiment #13 Joe Solution E00123456 Partner - Jane Answers PHY 221 Lab Instructor – Chuck Borener Thursday‚ 11 AM – 1 PM Lecture Instructor – Dr. Jacobs Abstract In this experiment‚ we test factors which effect friction. We pulled a wood block across a surface to determine whether the surface area of the block or the type of surface effects friction. We found that the surface area of the block did not change
Free Force Friction Mass
MEC 325/580 Lab Report CNC Machining Lab Report Date: March 18‚ 2013 Group Leader: Jian Wu Team Members: Group Number: G4 Regment No.: D Insturctor: CONTENTS 1.Objective and introduction. 2.Principles and practice. 3.Design and result. 4.Conclusion and recommendations. Appendices 1. Objective and introduction * Objectives Operate the CNC milling machine using G-codes‚ M-codes in a CNC program. * Equipment: Minitech CNC machine (Series 2) * Machine
Premium Milling machine Numerical control
Lab Report 7: Analysis of Cereal Introduction: The objective of this lab was to consult for the FDA regarding a recently surfaced scandal involving false reporting of iron content in cereal as well as iron tablets. The makers of the cereal and the iron tablets‚ respectively‚ were allegedly reporting higher amounts of iron in their products than actually existed‚ as a way to save money but continue to provide products with “adequate” amounts of iron. The FDA needed consulting in order to analyze
Premium Iron