Page I - Cover sheet In the middle f the page give name and number of your microorganism In the right lower corner provide - your name - Lab section number (Biol 108-005) - Date submitted ( 4/18/2013) - the unknown tube # is 5 Page II table of result - This page will have your table of results include the following information - Name of the test - Medium used - Indicator used - your results Part III - All the test done As many pages as needed to do a complete job. in this section
Premium Organism Bacteria Biology
’Neil 2002). The particular conditions that had to exist for this to apply were that the population had no mutation‚ had no natural selection‚ was a large population‚ had only random mating‚ and had no migration. For the cases to follow later in the lab‚ Cases 1 and 2 exemplify Hardy-Weinberg conditions. All of the others either have selection or not enough members in the population‚ which will be the most-closely observed
Premium Biology Experiment Evolution
Evolution Lab Report Marcos Chapa July 3‚ 2013 BIO 101 Rebecca Avants The purpose of the lab I have conducted is to analyze how altering the finch’s environment would affect the evolution of the finches by isolating each population of finches from each other‚ placing them each on a different island. This influence on the species by the environment is called allopatric speciation. One population of the finches that are located Darwin Island‚ which is 1 km‚ and the other population of finches
Premium Evolution Species Hypothesis
BIOLOGY GERMINATION EXPERIMENT INTRODUCTION: Germination is the resumption of growth of the embryo plant inside the seed. Requirements for germination: * proper temperature * the presence of adequate water * oxygen There are two types of cotyledons: the monocotyledons (“monocots”) and the dicotyledons (“dicots”). Monocots have one cotyledon. Rice and corn are monocots. Dicots have two cotyledons. Lentils‚ lima beans‚ and green beans are dicots.* Germination in Dicots 1
Premium Seed Germination
Raquel Johnson October 19‚ 2014 Solids: Recrystallization and Melting Points Organic Chemistry 2423 Lab Report: Recrystallization Abstract: The purpose of this lab was to purify an unknown compound by recrystallization. Taking an unknown compound and identifying it by purifying it from its impurities through the use of hot gravity filtration. Then to determine the unknown you were to take the melting point. An unknown compound was recrystallized from hot water to produce 0.99 grams (67% recovery)
Premium Temperature Solubility Solid
Physics Lab report Aammar Paracha Section MX Feb 6th 2015 OPTICS Abstract: This experiment revolves around using light rays and lenses. The experiment also discusses different properties of light rays. This experiment uses different lenses and measurements to produce images and observes different techniques to obtain the image position. Question and Answers: 1. Use your data to verify the Law of Reflection and then use Snell’s Law to calculate
Premium Optics Lens
Lab Report Procedure 6.1: Perform Benedict’s test for reducing sugars. Introduction: Benedict’s tests allows for the detection of the presence of reducing sugars. All monosaccharides are reducing sugars since all of them have active carbonyl group. Some disaccharides that are exposed to a carbonyl group are also reducing sugars but less reactive than monosaccharides. By mixing the sugar solution with Benedict’s solution and heating them‚ a redox reaction will occur. The copper (II) sulphate
Free Glucose Carbohydrate Sucrose
I. Introduction Photosynthesis the process where plants use sunlight (energy) to synthesize foods forming the products carbohydrates and water (H20 + CO2 + Light CH2O + O2). For photosynthesis to take place they need water‚ carbon dioxide and light and chloroplasts. Light is absorbed inside he thylakoid membrane of the chloroplasts‚ and the carbohydrate reaction or synthesis takes place in the stroma. In plants there are five kinds of chlorophylls with the same basic structure
Premium Photosynthesis Plant Oxygen
ABSTRACT On the past two weeks‚ I have done an experiment on hydrostatics‚ or is also known as fluid statics (fluid at rest) within the fluid mechanics field of study. This condition explains that in a stable condition‚ the fluid is at rest. The use of fluid in doing work is known as hydraulics‚ and the science of fluid in motion is known as fluid dynamics. INTRODUCTION The natural nature of fluids are they cannot remain stationary under the application of shear stress. However‚ fluid
Premium Fluid mechanics Force Fluid dynamics
Lab Report Density Name: Period: Problem How do you calculate Density? What units did you use for volume‚ mass‚ and density? When the cubes are placed in water which one will sink 1st? What is the ranking of the cubes lightest (1) to heaviest (10)? Is it true that the cube with the most mass will have the most density? Hypothesis I think the 1st cube was aluminum I think the 2nd cube was steel I think the 3rd cube was brass I think the 4th cube was copper I think the 5th
Premium Density Volume