10. Tubes 2‚ 6‚ and 7 showed the effect of pH on amylase activity. The results of this experiment indicate that the activity maximum of amylase is at pH 7.0‚ whereas pH 2.0 and pH 9.0 demonstrated very little activity. In this experiment‚ pH 7.0 showed the highest level of amylase activity. Tube 3 showed that amylase did not contain maltose contamination. Tubes 3‚ 4‚ and 5 showed that water had no starch or maltose contamination. Tube 3 directly showed that water did not have maltose or starch contamination
Premium Enzyme Amylase Starch
is the capacitative reactance‚ R is the resistance‚ and ω = 2π f ( f is the linear frequency). Apparatus • PC with DataStudio installed • Science Workshop 750 USB Interface Box • Power Amplifier • Voltage Sensor • AC/DC Electronics Lab Board • LCR meter • Connecting patch cords Experimental Procedure The experimental procedure can be divided into three parts: Part I: Using a Frequency Scan to Determine the Resonance Frequency • The first
Premium Alternating current Inductor Electrical resistance
The purpose of this experiment was to acquaint the students with basic laboratory procedures‚ methods‚ and techniques; to introduce the use of basic laboratory measuring devices; to demonstrate different methods of manipulation of numerical quantities. DENSITY AND SPECIFIC GRAVITY Materials and Methods Part 1: Density of an Unknown Solid 1. We first were asked from our laboratory instructor to attain an unknown solid and were asked to note down the number of the solid. 2. Determine
Premium Density Volume
McLean 1 Creating Acetylene Gas Introduction The purpose of the lab was to determine the ratio of air to acetylene results in complete combustion of acetylene gas. The balanced chemical equation for this experiment was C2H2(g) + O2(g) --> CO2(g)+ H2O(l). Complete combustion is the reaction of an element or compound with oxygen to produce the most common oxides and energy. Complete combustion occurs when the fuel and oxygen combine in exact proportions to completely burn the fuel
Premium Oxygen Combustion
Nervous System lab was designed to measure reaction times by using a variety of tests that affect the heart rate. These tests were the startle‚ stroop‚ Valsalva maneuver‚ diving reflex‚ and a test of our choice. The test our group chose to measure the heart rate in response to doing a trust fall to anticipate the stress right before the fall. To begin this lab we chose a participant‚ and then hooked their finger up to the pulse transducer sensor. Using the chart 5 program on the lab computer the participant’s
Premium Parasympathetic nervous system Autonomic nervous system Peripheral nervous system
Objective: One of the main learning experiences of this lab is to learn the importance of calibrating a sensor. In most cases‚ a sensor will not have an output that is exactly what you need. An example of this is a strain gage. A stain gage gives back a voltage‚ but with that given voltage a distance can be found. Introduction: In this experiment‚ the QNET-MECHKIT was used. This board has multiple compact sensors that can be used for experiments. For this lab we will be using the strain
Premium Metrology Measurement Angle
References: a) http://en.wikipedia.org/wiki/Reynolds_number b) http://www.engineeringtoolbox.com/reynolds-number-d_237.html c) http://www.engineeringtoolbox.com/laminar-transitional-turbulent-flow-d_577.html d) http://www.slashdocs.com/prqt/lab-report-osbourne-reynolds-apparatus.html APPENDIX The Reynolds Apparatus that was used during the experiment.
Premium Fluid dynamics Fluid mechanics Viscosity
The Virtual Lab – ELISA Test Lab: Immunology 09/04/2013 Instructors: Dr. Charlie Wilson Written by: Dipen Patel I. Objective: The purpose of the lab was to learn the procedure of performing an ELISA test to determine whether a particular antibody is present in a patient’s blood sample. ELISA is an abbreviation for “Enzyme-linked Immunosorbent Assay." II. Introduction: The interaction of antigen and antibody outside the body can be used to determine if patient
Premium Antibody Immune system ELISA
Example lab report of Synthesis of potassium tris (oxalato) ferrate (III) trihydrate Posted by Nurul Yunaliyana Experiment 5: Synthesis of potassium tris (oxalato) ferrate (III) trihydrate Purpose: to synthesis potassium tris (oxalato) ferrate (III) trihydrate ‚K3 [Fe (C2O4)3].3H2O. Introduction: Ferrous ammonium sulfate‚ Fe(NH4)2(SO4)2.6H2O is dissolved in a slightly acid solution‚ excess oxalic acid‚ H2C2O4‚ is added and the following reaction takes place: Fe(NH4)2(SO4)2.6H2O + H2C3O4
Premium Chemistry Iron Ammonia
Tori Suchy Physical Science Honors 1st block October 4‚ 2012 Balloon Powered Car Problem: In order to create a race car that can travel a minimum of eight meters powered by a nine inch balloon. We need incorporate Newton ’s Law of Motion including speed‚ velocity‚ and acceleration. Hypothesis: If a car were to be made out of homemade materials‚ then it would be possible for it to travel 8 meters powered by a nine inch balloon. Independent Variable: building the car from homemade materials
Free Newton's laws of motion Force Classical mechanics