Table 1: Density based on dimensional analysis Trial 1 Trial 2 Trial 3 Units Mass of sample 70.5466 70.5467 70.5465 g Dimensions of sample Length 4.98 4.98 4.99 cm Width 1.21 1.22 1.21 cm Height 1.21 1.22 1.22 cm Volum of sample 7.29 7.41 7.37 cm^3 Density of sample (based on dimensional analysis) 9.68 9.52 9.57 g/cm^3 Table 2: Density based on the displacement of water Trial 1 Trial 2 Trial 3 Units Mass of sample 70.5467 70.5465 70.5466 g Final volume of the
Premium Density Volume Water
Lab No.1: density‚ accuracy and precision Aim: to determine the relative precision and accuracy of different glassware items by calculating the density of a known substance. Introduction: the density of a substance is its mass per unit volume. (where P-density‚ m- mass and v- volume). Different materials usually have different densities and densities vary according to the pressure‚ temperature and purity of a substance. When measuring‚ there is always a small uncertainty or error and therefore
Premium Management Scientific method Education
Experiment 1 Laboratory Techniques and Measurements Purpose: To determine measurements of different items that vary from solids to liquids and be able convert those values to other SI units of measurement. Procedure: I used a variety of scientific tools such as; a ruler‚ beaker‚ graduated cylinder‚ volumetric flask‚ thermometer‚ burner‚ and digital scale to find unknown values of measurements for each of the indicated items and
Premium Water Boiling Density
report submitted: June 18‚ 2015 Title: Lab Techniques and Measurements PURPOSE: The purpose of this experiment is for the students to get a better knowledge with the laboratory tools and techniques. This experiment taught me how to convert between SI units and standard American units of mass‚ length‚ temperature‚ volume and time as well as how to measure the units. Students become proficient in laboratory techniques such as measuring temperature and volume and calculating within them. Procedure:
Premium Volume Density Measurement
Experiment: determination of densities Introduction The density of a sample of matter represents the mass contained within a unit volume of space in the sample. For most samples‚ a unit volume means 1.0 ml. The units of density‚ therefore‚ are quoted in terms of grams per milliliter (g/ml) or grams per cubic centimeter (g/cm3) for most solid and liquid samples of matter. Density is often used as a point of identification in the determination of an unknown substance. The density of the unknown might
Premium Density Volume Temperature
DENISTY LAB 2/25/13 Chemistry H. Mrs. Halme Objective: Your task is to determine the density of 3 known metals: Zinc‚ Copper‚ and Lead. They are each marked. You must then calculate the density of an unknown metal and determine its identity based on your data from your known samples. Reagents: None Equipment: Lead Copper Zinc Triple Beam Balance Graduated cylinder Unknown metal (Magnesium) Beaker Calculator Procedures Preparation: We observed the given equipment
Free Calculator Mathematics Division
Measurement of the Densities of Water and Alcohol Phuc Truong and Shane Steele Data Collected: September 8‚ 2014 2:05 P.M. Purpose: The purpose of the experiment is to measure the densities of liquids. Specifically‚ the two liquids that were used and measured in the research were deionized water (H2O) and alcohol (C2H5OH). Methods: Density is an intensive quantity that cannot be visually identified. Therefore‚ the most straightforward approach to this problem was to record the measurements of mass
Premium Water Volume Density
identify whether density is an extensive or intensive physical property. By using water displacement‚ the volumes of the paper clip samples were measured and the masses were obtained by using an electronic balance. Each mass and volume was unique to their sample so by using their values‚ density was used to identify substances in the lab. After conducting the experiment‚ the results showed that there was a positive slope between the different paper clip samples’ masses and their volumes. It was concluded
Premium Temperature Physical quantities Density
DENSITY OF LIQUIDS AND SOLIDS by Lab instructor: Due date: Results and discussion: The purpose of the experiment was to determine the densities of the unknown liquid and solid as precisely and accurately as possible in order to identify them. It was carried out first on distilled water in order to rule out systematic errors. A 10 mL beaker was placed on a top pan balance and “tared”. The beaker was then removed and 10 mL of distilled water was pipetted into it before it was placed
Premium Water Chemistry Volume
13 2.72g/cm3 53.95 11 4.9g/cm3 During the lab‚ the whole purpose of the lab was to determine density of both regular and irregular shaped objects. Throughout the lab I found out that both of the small and large silver rod‚ do not have the same density‚ and also found out that the gold rod is not real gold. My hypothesis is that since‚ the large and small silver rod has about the same density I believe that they would have about the same amount of volume. They both might displace the same amount of
Premium Density Volume