Pet E 367 Lab Report #1 * Yield of Bentonite and Attapulgite Clays * Rheological Characterization of Water-Base Drilling Fluids Experiment Date: January 31 2007 Prepared by: Jackie Chee (1103396) Group #7 Beattie L. Branch T. NREF 2-052 Markin/CNRL Natural Resources Engineering Facility 116street 91st ave February 13‚ 2007 Barkim Demirdal PhD Candidate at Petroleum Engineering Department 7-134 Markim CNRL Natural Resources Engineering Facility Edmonton‚ Alberta Canada T6G
Premium Viscosity
CHAPTER 1 1. List the seven SI base quantities‚ units‚ and symbols. TIME Second (s) 2. Give the correct SI derived units of the following quantities. Density Speed Acceleration Force Pressure kg/m3 Energy 3. Convert the following: μm (Ans. 1.22) a. 1.22 x 10-9 km = b. 6.523 x 10-4 nm = c. 2.5x 10-9 nm3 = d. 30.5 cm/s = e. 9.6 ng/mm2 = 4. Mm (Ans. 6.523 x 10-19) mm3 (Ans. 2.5 x 10-27) km/h (Ans. 1.09 x 106) kg/m2 (Ans. 9.6 x 10-6) Perform the following calculations and
Premium Kilogram Gold Mass
The edge of the cliff is 8 feet above the level of the water. The tip of his fishing rod is directly above the edge of the cliff and is 7 feet above the cliff. He lowers his fishing line so that it enters the water at the base of the cliff. The length of his fishing line‚ l‚ which is measured from the tip of his fishing rod to the place his line enters the water‚ and the angle between his line and the water‚ θ‚ are changing as the river carries his line downstream. The horizontal distance‚ r‚
Premium Fishing Length Linear equation
Laboratory Techniques and Measurements Peter Jeschofnig‚ Ph.D. Version 42-0165-00-01 Lab RepoRt assistant This document is not meant to be a substitute for a formal laboratory report. The Lab Report Assistant is simply a summary of the experiment’s questions‚ diagrams if needed‚ and data tables that should be addressed in a formal lab report. The intent is to facilitate students’ writing of lab reports by providing
Premium Density Water Volume
Practical Report Experiment 1 Abstract In this experiment we found that you can calculate the density of elements with close presotion with crude experiments Introduction The aim of this experiment was to see how close you could measure the density of atoms with crude experiments. The second part of the experiment dealt with Solubility of large ions and their Hydration enthalpy. Hydration enthalpy is the enthalpy change when 1 mole of an ionic substance dissolves in a solution to give a solution
Premium Chemistry Periodic table Chemical element
Measurement: Length‚ Mass‚ Volume‚ Density‚ and Time Peter Jeschofnig‚ Ph.D. Version 42-0267-00-01 Lab RepoRt assistant This document is not meant to be a substitute for a formal laboratory report. The Lab Report Assistant is simply a summary of the experiment’s questions‚ diagrams if needed‚ and data tables that should be addressed in a formal lab report. The intent is to facilitate students’ writing of lab
Premium Measurement Units of measurement Ruler
The lab performed was laboratory techniques and measurements. The purpose of this lab was to familiarize ourselves with different techniques used in the lab‚ taking proper measurements‚ and how to use the International System of Units (SI). Throughout lab we learned about mas‚ volume‚ length and temperature‚ and to be able determine density and concentration. To be able to documents properly and make effective observations we must be able to understand the International Measurement System. Length
Premium Measurement Units of measurement Density
1 Physics and Measurement CHAPTER OUTLINE 1.1 1.2 1.3 1.4 1.5 1.6 1.7 Standards of Length‚ Mass‚ and Time Matter and Model-Building Density and Atomic Mass Dimensional Analysis Conversion of Units Estimates and Order-ofMagnitude Calculations Significant Figures ANSWERS TO QUESTIONS Q1.1 Q1.2 Atomic clocks are based on electromagnetic waves which atoms emit. Also‚ pulsars are highly regular astronomical clocks. Density varies with temperature and pressure. It would be necessary to measure both
Premium Orders of magnitude Kilogram Mass
Lab #3 January 30‚ 2012 1. Title: Laboratory Techniques and Measurements 2. Purpose: The purpose of this lab is to learn laboratory techniques and to how to measure precisely. During this lab I will learn how to measure length‚ temperatures‚ volume‚ density‚ and mass using laboratory equipment. I will be using laboratory equipment to prepare dilutions and calculate them while using an algebraic formula. 3. Procedure: In order to perform this lab I needed the following materials:
Premium Density Water Volume
during the lab. Data Set Pressure in kPa Volume in mL 1 150 20 2 100 30 3 75 40 4 60 50 5 45 60 6 40 70 Graph: [10 points] Create a graph of your data for this part of the lab. You may use any graphing tool to create the graph‚ but be sure to follow common guidelines for creating a graph. INSERT GRAPH HERE Conclusion: Answer the following questions after completing the lab. 1) Describe the relationship that you observed between pressure and volume in this lab. Refer to
Premium Gas Thermodynamics Temperature