Introduction: The purpose behind (the first step in) this experiment is to show that similarly to week 1‚ the molarity of an acid or base in solution can be determined (so long as one value’s is known) using titration. In this case though‚ finding the molarity of the acid used in the reaction is then used to determine the percent of that acid in a vinegar solution and compared to the standard value for % acid present in vinegar. The second part of the experiment was to see if by titrating a solution
Premium Acetic acid Vinegar Concentration
Chemistry design: Fuel energy lab Research question: What is the energy density of cyclohexane‚ and how does it compare to the energy density of normal hexane? Variables: Independent variable – The independent variable in this experiment will be the type of fuel that will be used. This will be either Hexane or Cyclohexane. Each type will be given to us and labelled so it will be quite simple to control this variable. This cannot be measured using any apparatus so the lab assistant must be entrusted
Premium Heat Temperature Energy
Chemistry Lab Report on standardization of acid and bases. Purpose: To prepare standardize solution of sodium hydroxide and to determine the concentration of unknown sulfuric acid solution. Data and Calculations: This experiment is divided into two parts (Part A and Part B). In the first part of experiment‚ the standardize solution of sodium hydroxide is prepared by titrating it with base Potassium hydrogen phthalate (KHP). The indicator Phenolphthalein is used to determine that whether titration
Premium Sodium hydroxide
TITLE: THE EFFECT OF HEATING DIFFERENT SUBSTANCES INTRODUCTION: In this exercise‚ it was required to observe carefully what happened when certain substances were heated in a burner‚ and to note the appearance of the residue after heating. AIM: To observe the effects of heating different substances. MATERIALS: Hard glass test tubes Powered samples of Lead (II) nitrate Copper (II) sulphate Ammonium chloride Zinc sulphate Basic copper (II) carbonate‚ CuCO3. Cu(OH)2
Premium Gas Copper Sulfuric acid
Test 2 Name___________________________________ MULTIPLE CHOICE. Choose the one alternative that best completes the statement or answers the question. 1) Find the combination that will give a gas as a product A. AgNO3(aq) + NaI(aq) B. HCl(aq) + Na2CO3 (aq) C. MgCl2(aq) + K2CO 3 (aq) D. CaSO4 (aq) + (NH4)3 PO4(aq) 1) A) A B) C C) B D) D 2) 2) The balanced molecular equation for complete neutralization of H2 SO4 by KOH in aqueous solution is __________. A) 2H+ (aq) + 2OH- (aq)
Premium Mole Chemical reaction Sodium hydroxide
Chemistry Lab Report 1 Nicole H. Healey (Experiment 1 and 2) October 7‚ 2014 Data Collection: Table 1: (First Titration) C2O42- Analysis Sample 1 Sample 2 Molarity of KMnO4 0.02m 0.02m Weight of Sample 0.237g 0.225g Final Buret Reading 28.5ml 26.3ml Initial Buret Reading 0ml 0ml Volume of KMnO4 dispensed 28.5ml 26.3ml Moles
Free Titration Potassium permanganate Mole
Performed: June 25‚ 2013 Lab partner: Catalan‚ Christian A. Date Due: July 5‚ 2013 Date Submitted: July 5‚ 2013 EXPERIMENT 1 PREPARING BUFFERS AND BUFFER CAPACITY INTRODUCTION A buffer solution is one in which the pH of the solution is "resistant" to small additions of either a strong acid or strong base. Buffers usually consist of a weak acid and its conjugate base‚ in relatively equal and "large" quantities. A buffer system can be made by mixing
Free PH Buffer solution Acid dissociation constant
Lab for Chemistry 221 Lab: How much sugar is in a Can of Coke? Abstract: A 50mL (we used 100mL) volumetric flask was used to determine the amount of sugar in a can of Coke per mL in 5 different solutions. Using the calibration curve we determine the amount of sugar per mL in a can of coke. This experiment concluded that there is 43.83g of sugar in a 12oz can of Coke. Introduction: This experiment was conducted to determine the amount of sugar in a can of Coke and to and use a calibration
Premium Mass Kilogram Water
Table 1: Data Collection Table – Contains all of the primary data directly obtained from the lab. Indicator | Initial volume of NaOH in burette (ml) ±0.05 | Final Volume of NaOH in burette (ml) ±0.05 | Final – initial Burette Reading (Volume of NaOH used) (ml) ±0.1 | Qualitative Observations | Phenolphthalein | 0.00 | 0.90 | 0.9 | At first when the base was being dropped into the vinegar there wasn’t a color change‚ however when the solutions came close to full titration‚ the solution
Premium PH indicator Sodium hydroxide Titration
Name Lab Section GTA Station # 5. Extraction Pre-lab questions Complete the following questions and submit before beginning the experiment. 1. Which layer will be the aqueous layer when using dichloromethane (methylene chloride) as the solvent (i.e.‚ top or bottom)? Which layer will be the aqueous layer when using ether as the solvent? 2. When everything has been separated in Part D‚ which compounds will be in test tubes 1‚ 2‚ and 3?
Premium Chemistry Oxygen Solvent