…………………………………………………………………………. 12 Chemical Changes Experiment 3 …………………………………………………………………………. 15 Classification of Matter Experiment 4 ………………………………………………………………………….17 Chemical Nomenclature: The Language of Chemistry Experiment 5 ………………………………………………………………………….22 Water of Hydration Experiment 6 ………………………………………………………………………….25 Gases Experiment 7 ………………………………………………………………………….27 Oxygen Experiment 8 …………………………………………………………………………
Premium Chemistry Laboratory glassware Sodium chloride
Example lab report of Synthesis of potassium tris (oxalato) ferrate (III) trihydrate Posted by Nurul Yunaliyana Experiment 5: Synthesis of potassium tris (oxalato) ferrate (III) trihydrate Purpose: to synthesis potassium tris (oxalato) ferrate (III) trihydrate ‚K3 [Fe (C2O4)3].3H2O. Introduction: Ferrous ammonium sulfate‚ Fe(NH4)2(SO4)2.6H2O is dissolved in a slightly acid solution‚ excess oxalic acid‚ H2C2O4‚ is added and the following reaction takes place: Fe(NH4)2(SO4)2.6H2O + H2C3O4
Premium Chemistry Iron Ammonia
McLean 1 Creating Acetylene Gas Introduction The purpose of the lab was to determine the ratio of air to acetylene results in complete combustion of acetylene gas. The balanced chemical equation for this experiment was C2H2(g) + O2(g) --> CO2(g)+ H2O(l). Complete combustion is the reaction of an element or compound with oxygen to produce the most common oxides and energy. Complete combustion occurs when the fuel and oxygen combine in exact proportions to completely burn the fuel
Premium Oxygen Combustion
TITLE OF EXPERIMENT 2 : DILUTION 2.1: OBJECTIVES Upon completion of this experiment‚ students should be able to: 1. determine the concentration of coloured solution such as FeCl3 by using dilution and colour differentiating (colorimetric) techniques. 2.2: INTRODUCTION Concentration can be expressed in many different ways such as percentage volume and percentage weight etc. In laboratory‚ normally concentrations were expressed as molarity and normality. Molarity is the
Premium Concentration Chemistry
AP Chemistry Lab 2: Analysis of Alum Lab Objective: In this lab we will analyze alum by two techniques in order to verify its identity. The melting point and the mole ratio of hydrated water to anhydrous aluminum potassium sulfate will be determined. Lab Procedure: 1. Use a mortar and pestle to crush alum. 2. Pack the alum in capillary tube‚ and then fasten it to the thermometer. 3. Fasten the thermometer to the ring stand. 4. Immerse the bottom of the
Premium Chemistry Water Oxygen
COLLIGATIVE PROPERTIES 1. Calculate the vapor pressure when 10.o mL glycerol (C3H8O3) is added to 500.0 mL water at 500C. At this temperature the vapor pressure of pure water is 92.5 torr and its density is 0.988 g/mL. Density of glycerol is 1.26 g/mL. 2. Calculate the boiling point and freezing point of the solution if 1.00 kg of ethylene glycol (C2H6O2) is added to a car radiator which contains 4450 g water. a. Kb of water = 0.512 oC/m at normal boiling point of 100oC b. Kf of water
Premium Concentration Ethanol Water
AP/IB Chemistry Internal Assessment Lab Format The following titles and subtitles (in bold) should be used for your lab report and given in this order within your lab report. Title: choose one to fit your experiment I. Design A. Problem – must be a focused‚ clear research question. B. Hypothesis (When appropriate) • Clear answer to Problem – • Logical rational • your conclusion should address the hypothesis you are giving here. C. Variables
Free Scientific method Measurement Control
The average University student has many tasks to accomplish and much studying to do while combating the onslaught of sleep. Students at the University of the West Indies Mona are no different and recommended amongst themselves a highly rated and popular health supplement “Yeast-Vite” [8]. Yeast-Vite is a health supplement pill which helps people fight fatigue and improve alertness. The active ingredients in Yeast-Vite are caffeine‚ vitamin B1‚ vitamin B2‚ vitamin B3. The other ingredients are:
Premium Analytical chemistry Chromatography Nervous system
Measurement of Capacitance using Arduino – An Interrupt-based Approach: Part I SAIKAT PATRA‚ SHIBENDU MAHATA Introduction Capacitive sensors are widely employed to measure various physical and chemical process parameters such as displacement‚ acceleration‚ thickness‚ force‚ pressure‚ stress‚ level‚ and humidity. The measured value of capacitance is then calibrated in terms of the process parameter for indication and/or control applications. This project presents an interrupt-based approach by
Premium Chemistry Chemical reaction Reaction rate
Sample Short Lab Report By Charles M Borener Jr April 24‚ 2009 Kinetic Friction Experiment #13 Joe Solution E00123456 Partner - Jane Answers PHY 221 Lab Instructor – Chuck Borener Thursday‚ 11 AM – 1 PM Lecture Instructor – Dr. Jacobs Abstract In this experiment‚ we test factors which effect friction. We pulled a wood block across a surface to determine whether the surface area of the block or the type of surface effects friction. We found that the surface area of the block did not change
Free Force Friction Mass