PHY 114 Faraday’s Law of Induction Stephanie Scott Section: 10849 Group #3 Bochao Li 3/31/15 Abstract: The objective of the Faraday’s Law of Induction lab was to verify Faraday’s law of induction by measuring the emf generated in a small coil and comparing it with the calculated value. Secondly the goal was to investigate the relationship between the emf and the frequency of the driving signal. The magnetic field was found to be uniform throughout. For the frequency of 40 Hz‚ the average
Premium Magnetic field Maxwell's equations
Institute Physics Course 2014 - Rocket Lab Report Title: RockSim and Electronic Altimeter Measurement Techniques Name: Scarlet Henriquez Email: scarletpatricia94@aol.com LAB SESSION ___8____Assignment _____7_____ Due Date: ___7/8/14______ Objective: Launch a smaller rocket to learn how to compare RockSim predictions (computer based) to an actual instrument measurement carried by the rocket (Electronic Altimeter). This Lab shows how better the electronic measurement
Premium Rocket Mathematics Flight
# Now You See It – Copper Cycle Lab The purpose of the lab is to discover what happens when someone executes a series of procedures‚ beginning with copper metal. What is done | What is observed | 1. Started with copper‚ Cu (s). | reddish‚ brownish‚ orange-ish‚ powder-like | 2. Added nitric acid‚ HNO3 (aq). | acid turns blue and smells like chlorine. | 3. Added water‚ H2O (l). | stayed the same | 4. Added sodium hydroxide‚ NaOH (aq). | changed consistency‚ gel-like | 5. Heated the
Premium Sulfuric acid Copper Zinc
PRE LAB REPORT Reynaldo Riboul TLC and Column Chromatography October 6‚ 2013 Table of Chemicals: Chemical Hazards Mol. Wt. Density Grams Moles Acetone Flammable‚ Irritant 58.08 g mol−1 0.791 g cm−3 2.0 g 0.0344 Hexane Flammable‚ Irritant‚ Dangerous to Environment 86.18 g mol−1 .6548 g mL−1 9.0 g 0.1044 Fluorene Very toxic to aquatic life with long lasting effects 166.223 g/mol 1.202 g/mL 0.3 g 0.00180 Fluorenone Irritant 180.20 g mol−1 1.13 g/cm3 0.3 g 0.00166
Free Solvent Oxygen Laboratory glassware
Lab Report 3 In this lab‚ we will take a trip to the planetarium lab and will learn about Right ascension and declination‚ and altitude and zenith. After looking at the different points shown‚ we will log the altitude and zenith in the chart in our lab manual. Now we will look at the same points and label the right ascension and declination. Then we will learn about the easiest way to locate the star Polaris. As we started the first program‚ we answered a few questions to make sure we knew
Premium
MEC 325/580 Lab Report CNC Machining Lab Report Date: March 18‚ 2013 Group Leader: Jian Wu Team Members: Group Number: G4 Regment No.: D Insturctor: CONTENTS 1.Objective and introduction. 2.Principles and practice. 3.Design and result. 4.Conclusion and recommendations. Appendices 1. Objective and introduction * Objectives Operate the CNC milling machine using G-codes‚ M-codes in a CNC program. * Equipment: Minitech CNC machine (Series 2) * Machine
Premium Milling machine Numerical control
I.Purpose The purpose of this lab is to show how potential energy and kinetic energy is shown and transferred using a model rollercoaster. This lab also demonstrates the Law of Conservation of Energy. II.Introduction Potential and Kinetic energy have a very big relationship. The Law of Conservation of Energy states that “Energy cannot be destroyed or created‚ but can be transformed or transferred.” This lab will help demonstrate this law and show the conversion between Kinetic and Potential
Free Energy Potential energy Conservation of energy
Alixandria Zeidel Physics 131 – section LZ Hasbrouck 208 10/01/14 Forces and Newton’s 2nd law Abstract The purpose of this lab was to learn about how force influences acceleration. A hanging mass is tied to a frictionless glider and the mass is dropped. While the glider is being pulled by the mass it is possible to measure to tension force on the rope between the two objects. A motion sensor graphs the movement of the system and from the slope it is possible to calculate the acceleration of both
Premium Force Aerodynamics Mass
Sample Short Lab Report By Charles M Borener Jr April 24‚ 2009 Kinetic Friction Experiment #13 Joe Solution E00123456 Partner - Jane Answers PHY 221 Lab Instructor – Chuck Borener Thursday‚ 11 AM – 1 PM Lecture Instructor – Dr. Jacobs Abstract In this experiment‚ we test factors which effect friction. We pulled a wood block across a surface to determine whether the surface area of the block or the type of surface effects friction. We found that the surface area of the block did not change
Free Force Friction Mass
Fire Bug. Objective : To demonstrate the differences between physical and chemical changes while observing the laws of conservation of matter and energy. Procedure : Watch each part of the experimental demonstration and make predictions about what will happen in each scenario. 1. View the three scenarios listed below. You must observe and analyze these as part of the lab. The Iced Tea Debate The Salty Soup The Fire Bug 2 Use the DATA chart provided for recording observation
Premium Energy Conservation of energy Chemistry