conducted on 13th August 2008 in Machines Dynamics Laboratory. The experiment was conducted in groups of four‚ and was supervised by lecturer Mr. Mohd Azahari Johan. Conducting this experiment is for fulfilling the requirements of Applied Mechanics Lab (MEC 424). A pendulum is defined as body so suspended from a fixed point as to swing freely to and from by the alternate action of gravity and momentum. It is used to regulate the movements of clockwork and other machinery. Therefore‚ a compound
Premium Pendulum
hold another paperclip at the appropriate distance: six cm‚ seven‚ eight‚ nine‚ ten‚ twelve‚ fourteen‚ sixteen‚ eighteen‚ and twenty centimeters. 5. Lab partner must close eyes tightly. 6. Starting with the largest distance‚ place either one or two ends onto your partners skin (ALTERNATE RANDOMLY so the partner can’t guess!!!) 7. Have lab partner tell you how many ends they can feel. Do this 5 or 6 times. 8. Then try the next smaller distance and repeat steps 6 and 7. 9. Record
Premium Skin Finger Human body
Chart 3.1: Velocity at 3 degrees Chart 3.2: Velocity at 6.3 degrees Chart 3.3: Velocity at 8.5 degrees Chart 3.4: Velocity at 90 degrees Discussion: The results that were observed from this lab helped prove what was hypothesized. As chart 1.4‚ 2.4 and 3.4 displayed the object dropped off of the 90 degree slope was the quickest to cross 200cm‚ had the highest velocity and the highest acceleration. This was because at 90 degrees the gravitational
Premium Velocity UCI race classifications Tour de Georgia
smaller than 0.85mm (Pass through 15 B.S. sieve) and bigger than 0.60mm (Retain at 25 B.S. sieve). A H M 531 Compressive and tensile strength of cement mortar By: Ahmed Essam Mansour The Civil Engineering Center 1 Visit www.AHM531.com for more lab reports and lecture notes! A H M 531 The Civil Engineering Center In the cement-sand mortar‚ the proportion between Cement and Sand is 1:3 and the W\C = 40%. The same mixture is used in the compressive test a nd in the tensile test. Apparatus
Premium Materials science Tensile strength Concrete
A. What is the name of the pigment that captures light? Chlorophyll B. Why does the pigment appear green? It absorbs other colors of light such as red and blue‚ so in a way the green light is reflected out since the pigment does not absorb it. 2. List two variables besides the wavelength (color) of light which might affect the rate of food production in plants. Light intensity and carbon dioxide 3. Why is chlorophyll important for all biological life? It is necessary for photosynthesis which
Free Photosynthesis Carbon dioxide Oxygen
01.07 Accuracy and Precision: Balance Lab Worksheet Calculations Show all of your work for each of the following calculations and be careful to follow significant figure rules in each calculation. 1. Part I: Density of Unknown Liquid 1. Calculate the mass of the liquid for each trial. (Subtract the mass of the empty graduated cylinder from the mass of the graduated cylinder with liquid.) Trial 1 36 - 25.5 = 10.5 Trial 2 36.5 - 25.5 = 11 Trial 3 36.9 - 25.5 = 11.4 2. Calculate the
Premium Accuracy and precision Density Volume
Ammonia and Hydrochloric Acid Lab Chemistry 1 Abstract The straw should be cut shorter to 8 cm in order to make the solid ring appear in the center of the straw. We achieved our goal‚ cutting the straw caused the gases to not have to go as far‚ and meet in the middle. Background The particles in a gas are very loose and tend to move around a lot very quickly. The particles in a solid are very compact and vibrate but don’t really move very much. The particles in a liquid however are more
Premium Gas Chemical reaction Chemistry
PRE LAB REPORT Reynaldo Riboul TLC and Column Chromatography October 6‚ 2013 Table of Chemicals: Chemical Hazards Mol. Wt. Density Grams Moles Acetone Flammable‚ Irritant 58.08 g mol−1 0.791 g cm−3 2.0 g 0.0344 Hexane Flammable‚ Irritant‚ Dangerous to Environment 86.18 g mol−1 .6548 g mL−1 9.0 g 0.1044 Fluorene Very toxic to aquatic life with long lasting effects 166.223 g/mol 1.202 g/mL 0.3 g 0.00180 Fluorenone Irritant 180.20 g mol−1 1.13 g/cm3 0.3 g 0.00166
Free Solvent Oxygen Laboratory glassware
Purpose: The purpose of this lab is to identify the presence of cations and anions in four unknown solutions by identifying whether they are copper‚ silver‚ iron‚ or chloride ions which is done by adding sodium hydroxide‚ solid copper‚ silver nitrate‚ and potassium thiocyanate to the solutions and analyzing the chemical reactions. Introduction: Chemical change‚ unlike physical change is the change in the composition of a substance rather than simply its shape‚ size‚ or state (Marie‚ 2015). Signs
Premium Ion Chemistry
3.2 “Lab-on-a-Chip” A Lab-on-a-Chip (LOC) device‚ also known as a micro-total-analytical system (microTAS) or microfluidics device‚ is a device that can integrate miniaturized laboratory functions (such as separation and analysis of components of a mixture) on a single microprocessor chip using extremely small fluid volumes on the order of nanoliters to picoliters. From a technology categorization perspective‚ LOCs can be viewed as a subset of microelectromechanical systems (MEMS) and combine
Premium Cantilever