Economic Labour: 3 people (8 hr. /ppl) Installation+capital cost: $1‚835‚202.809 Utility: Utilities | Quality | Electricity (pump 70 KW × 8 pumps) | 560 KW | Service water | 224‚779.5 kg/hr. | Maintenance: $13‚499 /year The wastewater from oil refinery plant will store in the decant tank before go to the CPI oil/water separator process. Due to the condition if CPI separator needs the temperature around 50°C but the wastewater from oil refinery has temperature high to 107°C.
Premium Water Heat exchanger Liquid
Ball mill as general-purpose grinding equipment is widely used in mineral dressing‚ building materials‚ chemical industry‚ etc. To make the ball mill operate well‚ and we must strictly abide by the procedures of operation and maintenance. Before starting the ball mill‚ check whether the connecting bolt‚ gears‚ couplings are tightened. Check whether the oil of the oil tank and the reducer is in the adequacy‚ and whether the lubricating device and instrumentation have problems. Determine the flow
Premium Gear Rack and pinion Liquid
1. INTRODUCTION Objectives of the project: (a) Develop a formulation of Atenolol HCL microemulsion for ocular application to decrease IOP in case of glaucoma. (b) Improve the quality of patient’s life suffering from glaucoma. (c) Reduce the number of dosing per day. 1.1 Eye "If a physician performed a major operation on a seignior (a nobleman) with a bronze lancet and has saved the seignior’s life‚ or he opened the eye socket of a seignior with a bronze lancet and has saved the seignior’s eye‚ he
Premium Liquid
GCSE Science – Investigative Skills Assignment – Marking Guidelines Chemistry 1.2 – Viscosity of Oils For submission in May 2007 or May 2008 Please mark in red ink‚ and use one tick for one mark. Subtotals for each part of each question should be written in the right hand margin. Please add annotations where necessary to explain why marks have or have not been awarded. Enter the marks for Section 1 and Section 2 and the total mark on the front cover of the answer booklet. The teacher must sign and
Premium Measurement Liquid Ball bearing
Brenton science homework Aim: In science we did an experiment about elephant skin‚ it was about if elephants cool down quicker when wet or dry. Equipment: 2 thermometers and beakers‚ hot water (to put inside of the beaker)‚ tap water (to wet the cotton)‚ pen‚ paper‚ ruler and a rubber (this is for your graph and data) Method: first get two beakers then wrap one in cotton wool and wet it with a tap water temperature representing the water an elephant would spray on its self to cool down ‚ then
Premium Debut albums Thermodynamics Temperature
EXPERIMENTAL MANUAL Mass Transfer Lab Diffusion Coefficient Apparatus DEPARTMENT OF CHEMICAL ENGINEERING UNIVERSITY OF GUJRAT‚ GUJRAT. GENERAL OPERATING PROCEDURES General Start-up Procedure: Prior to running an experiment‚ students are advised to perform the following startup procedure. Fill the water with clean (preferably filtered) water to approximately 20 mm from the top. Plug the main cable to the electrical supply. Be sure that the voltage of the supply is correct
Premium Liquid
European Automobile Manufacturers Association ACEA EUROPEAN OIL SEQUENCES 2012 SERVICE FILL OILS FOR GASOLINE ENGINES LIGHT DUTY DIESEL ENGINES ENGINES WITH AFTER TREATMENT DEVICES and HEAVY DUTY DIESEL ENGINES Laboratory tests for gasoline and light duty diesel engine oils‚ Engine tests for gasoline and light duty diesel engine oils‚ Laboratory tests for engine with after treatment devices‚ Engine tests for engine with after treatment devices‚ Laboratory tests for heavy duty diesel
Premium Diesel engine Internal combustion engine Diesel fuel
Raymond mill in the course of this malfunction ‚ according to the following processing : Raymond mill is a common fault : no less powder or flour production is low . Causes: ( 1 ) Locks powder is not adjusted‚ Mifengbuyan ‚ resulting powder suck . ( 2 ) blade wear and material shovel can not afford . Remedy: ( 1 ) checking and adjusting locks sealed powder was found to be leaking at the blade . ( 2 ) Replace the blade . Raymond Mill Troubleshooting II : refined powder too thick or too thin
Premium Windmill Gas turbine Liquid
Cross Linking effects on Polymers Purpose To observe the properties of the polymers with different amount of borax to see the effects of cross linking. Question How does the amount of a cross linking substances affect physical properties of a polymer Experimental Design A polymer was made with precise measuring of all the reactants especially different measurements of Borax solution as it was the key to cross linking. Physical properties of all the polymers were observed and the role of
Premium Polymer Measurement Liquid
Task 1 Foundry Work Sand casting involves many sequences and there are as follows: - Design and manufacturing the casting. When doing this all vertical edges must be tapered as to make it easier to lift the pattern out of the mould. - Contraction allowances have to be added to the pattern because it shrinks in size in all dimensions. In this case it’s Aluminium‚ which has a contraction allowance of 1.3%. - Machining allowance: Castings are usually machined so that they fit perfectly with
Premium Leak Solid Aluminium