with an acetic anhydride. Color impurities present in the solid acetaminophen will be removed and then the decolorized product will be collected on a Büchner funnel for further purification by crystallization. Purity will then be determined by melting point. Introduction: Acetaminophen is commonly used as an analgesic to reduce pain and fever. In this experiment it is prepared by the reaction of p-aminophenol with acetic anhydride‚ as illustrated below. Results: Isolation of crude acetaminophen The
Premium Melting point Yield Acetic anhydride
The purpose of the experiment was to perform an electrophilic addition reaction by the bromination of cinnamic acid. The product of this reaction is 3-Phenyl-2‚3-dibromo propionic acid‚ which is purified by recrystallization. Cinnamic acid (3-phenylprop-2-enoic acid) is an unsaturated carboxylic acid. The electron rich π cloud (see Figure 1) in the double bond of this structure is nucleophilic and can be considered a Lewis base. It can therefore be saturated by the addition of a halogen to the double
Premium Oxygen Chemistry Carbon
unknown sample was number 18. I did three melting point trials‚ which resulted in a melting point range of approximately 120°C to 122°C‚ as shown in Table 1. I also did two mixed melting point trials using Benzoic Acid and Succinimide‚ as shown in Table 2. Percent recovery is 28.26 grams. Table 1: Unknown Melting Point Trials Trial Melting Point 1 120°C – 122°C 2 120°C – 122°C 3 119°C - 122°C Table 2: Mixed Melting Point Trials Trial Benzoic Acid MP Unknown #18 MP Succinimide MP 1 122°C
Free Chemistry Chemical substance Benzene
1: MELTING POINT AND BOILING POINTS OF ORGANIC COMPOUNDS ABSTRACT The properties of organic compounds depend on their chemical structures. Intermolecular forces of attraction affect physical properties such as melting and boiling point. Through the Thomas Hoover apparatus‚ the melting point of 8 test compounds was determined. Salicylic acid exhibited the highest melting point while naphthalene‚ the lowest. The stronger the intermolecular forces of attraction‚ the higher the melting point. Boiling
Premium Carboxylic acid Hydrogen bond Organic chemistry
repCHEMISTRY I - LABORATORY EXERCISE MANUAL LABORATORY EXERCISE 10: Melting Point and Boiling Point Determination This is a traditional lab. You’ll simply follow the step-by-step procedure‚ keeping records of your measurements and observations. Each student will write their own lab report‚ which should include the following: Name: Names of lab partners: Date of Experiment: Date Report Submitted TITLE: Purpose: A brief statement about what the experiment is designed to determine
Premium Liquid Temperature Water
Melting Points Elizabeth McGrail Organic Chemistry I 25 January 2013 ABSTRACT The objectives of this lab are‚ as follows; to understand what occurs at the molecular level when a substance melts; to understand the primary purpose of melting point data; to demonstrate the technique for obtaining the melting point of an organic substance; and to explain the effect of impurities on the melting point of a substance. Through the experimentation of three substances‚ tetracosane‚ 1-tetradecanol and
Premium Chemistry Molecule Temperature
Melissa Carrithers AP Chemistry period 6 2-11-15 Determination of Ka of Weak Acids Purpose: The purpose of this lab is to find the strength of weak acids by determining the equilibrium constants for their ionization reactions in water. Is to use their measured pH values to calculate the pKa for the two unknown weak acids thus determining their identities. Hypothesis: If we neutralize a solution that contains a weak acid by adding a strong base to the solution‚ then the ions will be isolated and
Free PH Sodium hydroxide Acid
Sample Lab Report for CHM 152 Name Lab Partner(s) Abstract: The physical properties‚ including the boiling point‚ density‚ and refractive index were measured for unknown liquid #16. The infrared (IR) spectrum of the compound was also taken. Based on the data collected‚ it was determined that the compound was likely to be salicylaldehyde. Introduction The purpose of this experiment was to determine the identity of an unknown organic liquid by measuring some of its physical
Premium Temperature Liquid Fundamental physics concepts
Acid Determination of Vitamin C Tablets and Salt Solutions Chem 1290-016 03-05-2010 ------------------------------------------------- Purpose: The purpose of this lab was to use acid-base titrations to find the mass percent of ascorbic acid in a Vitamin C tablet. A known concentration of sodium hydroxide was used and the value found was compared to the stated amount of ascorbic acid listed on the vitamin container. Also in this lab the acidity of different salt solutions were tested using
Premium PH indicator Base Acid
Summary of Results A. Melting point of Benzoic Acid Temperature (¡ÆC) Observation Unmelted White salt First liquid appear point 122 Grainy and shiny white Becoming all liquid 125 Clear B. Melting point of unknown #42 1st trial Temperature (¡ÆC) Observation Unmelted Shiny light yellow crystal First liquid appear point 99 Grainy yellow Becoming all liquid 101 Clear 2nd trial Temperature (¡ÆC) Observation Unmelted Shiny light yellow crystal First liquid appear point 95 Grainy yellow
Premium Liquid Temperature Solid