Determination of Length‚ Mass‚ and Density Table of Contents 1 – Introduction ……………………………………………........…. Page 3 2 – Theory ………………………………………………………...... Page 3 3 – Experimental Procedure and Results …...………………..…. Page 6 4 – Discussion ………………….……………………….....….…… Page 9 5 – Conclusion ………………………………………….....…….... Page 9 6 – Bibliography …………………………………………......… Page 10 1- Introduction The purpose of this experiment is to learn how use a variety of tools that will aid in the gathering
Premium Measurement
Finding Density Density is defined as mass per unit volume‚ which can be used to determine the object or substance observed. Many people use the density of objects to find what it is and how to classify the object. The object of the lab conducted was to find the density of the substances given and to find what the unknown liquid and solid were. The process to finding what the unknown solid and liquid were‚ was to find the density and to conduct multiple trials so when the density
Premium Density Temperature Volume
Experiment 5 Liquids and Solids Chemistry 1211 Fall 2012 Section 1: Abstract‚ Experiment and Observation Abstract: The purpose of this experiment is to determine the boiling point of a liquid and the melting point of a solid. We also were able to observe the difference between boiling and melting point Experiment and Observation: We used isopropyl alcohol and set up an experiment to observe the boiling point. We set up a second experiment using acetamide to determine
Premium Temperature Gas Liquid
A safety audit for the gas-solid fluidization experiment was conducted. The following safety concerns were found when performing the audit: operating beyond the operating limits‚ spillage of the beads‚ risk of head injury from bending over to change the beads in the apparatus or from the low bar‚ and congestion of the workspace. One of the biggest safety concerns with this lab involved the small glass beads that acted as the solid in the experiment. If the gas flow rate goes below 50 standard cubic
Premium Glass Risk Causality
LAB REPORT # 1 DENSITY DETERMINATION CHEMISTRY 100 – 04 INTRODUCTION: The purpose of this experiment is to find out the density of the unknown solid object by determining the mass and the volume through the experiment. To do this we will be get the mass of the object and determine the volume of the object by placing it into a liquid. Then we will divide mass by volume and get its density. PROCEDURE: 1) Obtain a solid metal 2) Weigh the dry sample carefully to
Premium
between specific limits moisture contents. Below these levels they have a solid consistency and above a liquid consistency. Therefore‚ the soil has two important properties to be analyzed‚ the Liquid Limit (LL) and the Plastic Limit (PL). The Liquid Limit is the moisture content that makes the soil has a liquid behavior. The Plastic Limit is the moisture content below which the soil becomes from the plastic state to the semi-solid state‚ which means it loses the ability to be shaped and starts to become
Premium Soil Water Aquifer
Lab 4 - Molar Mass of a Volatile Liquid Purpose: To determine the molar mass of an unknown liquid whose boiling point is between room temperature and the boiling point for water. Key Terms: List and define any additional new terms relevant to this experiment. volatile – intermolecular forces - Key Formulas: Write the following formulas. Ideal Gas Law Molar Mass Relationships: The Dumas Method - In 1826 Jean-Baptist Dumas developed a method for determining
Premium Gas Water
be adopted for soft soils. 13.0 FIELD DENSITY TEST 13.1.1 Aim Determine in-situ density Determine‚ if required‚ percent of maximum density which has been achieved 13.1.2 Learning Outcome Describe the Field Density Test theory and its use Explain the Principle Determine Field Density by the Sand Replacement and Rubber Balloon Methods Calculate Dry Density and Relative Compaction Write a report on each test exercise 13.1.3 NEED AND SCOPE The in-situ density of natural soil is needed for the determination
Premium Standard deviation Normal distribution Statistics
Density Column What is density? We will be working with many different liquids. Each of the liquids has a different‚ characteristic density. One way to think about density is how thick or heavy an object is. The liquids with lighter densities will float. The liquids with heavier densities will drop to the bottom. You may have noticed that sometimes‚ liquids mix together – this is because the chemicals dissolve in each other. During our experiment‚ the liquids will stay separate because we will
Free Density
Density of Solutions Lab Purpose: The purpose of this lab was to find out the densities of the known and unknown Solutions that were given to us. This can be found by dividing the mass by the volume of the Solutions. The other purpose of this lab was to perfect our skills in finding out the percentage error‚ uncertainties‚ random error‚ and systematic error. Variables: Independent: Mass Percentage of Solution (KCl); Unknown Solution; Temperature Dependent: Density Materials: 10.00 mL
Premium Concentration Measurement Density