References: Moran‚ Shapiro‚ Munson‚ DeWitt. (2003). Introduction to Thermal Systems Engineering: Thermodynamics‚ Fluid Mechanics‚ and Heat Transfer. John Wiley & Sons. Manufacturing Engineering Lab II: Laboratory Manual. Department of Manufacturing and Materials Engineering. (2013). Various internet resources. Retrieved December 10th 2013.
Free Heat transfer Heat
Physical and Chemical Change Objective: Recognize and distinguish between chemical and physical changes. Materials: - lab balance - microspatula - lab burner - dropper pipet - 5 test tubes - mortar and pestle - test tube rack - magnet - test tube holder - insulating pad - watch glass - safety goggles - glass square - lab apron or coat - copper sulfate pentahydrate - iron fillings - sodium chloride - magnesium ribbon - hydrochloric acid - paper
Premium Chlorine Mixture Sulfuric acid
Derricka Joe Period 5 1 Oct.‚ 2014 Lab Experiment One: Physical Properties Lab Analysis: For our first unknown‚ we observed the color and odor of the substance. The substance was a clumpy‚ white‚ crystal-like substance and it smells like new plastic. When we tested the solubility in water it resulted insoluble and in ethanol it resulted soluble. This substance could not be tested for electrical conductivity because the water was insoluble. We then tested for the PH value and it was neutral. The
Premium Oxygen Water Ethanol
Pre-Lab Work Sheet Which type of compound usually has higher melting points: ionic compounds or covalent compounds? What is the reason for this difference in melting points? (3 points) Ionic compounds have higher melting and boiling points than covalent compounds. The electrostatic attraction in an ionic bond is very strong hence a lot of heat energy is required to break it down‚ ionic bonds have high melting and boiling points. In covalent bonds‚ the intermolecular forces are very weak and
Premium Ionic bond Covalent bond Chemical bond
Toxicology Lab 1. In this investigation‚ a wide range of concentrations of Sodium Chloride (NaCl) solution were created and the effects that they had on radish seeds were tested. This ultimately created a doseresponse experiment in which it was detectable whether or not radish seeds were a reliable bioassay for the toxicity of NaCl. The goal of this experiment was to determine a correlation between toxicity and seed germination/radicle
Premium Germination Seed Embryo
Salinity is the measure and concentration of all the salts dissolved in water. Usually measured in parts per thousand (ppt or )‚ ocean salinity is 35ppt and the average river water salinity is 0.5ppt or less (University of Rhode Island). Many factors go into salinity‚ making water salty. To name a few‚ salinity affects the environment through sediment from rocks washes into the ocean‚ evaporation of ocean water‚ and sea ice formation are known to increase the salinity of the ocean (NASA). It
Premium Sodium chloride
Lab 5 The Diffraction Grating Chinua McDonald Objective: To measure the wavelength of light with a diffraction grating. Theory: The two types of diffraction gratings are the transmission and reflection gratings. They are made by ruling on a piece of glass or metal a number of evenly spaced lines with a fine diamond point. Diffraction phenomena can be analyzed in terms of Huygens’ principle‚ according to which every point on the wave front of a wave should be considered as a source
Premium Light Diffraction Wavelength
indicated by a very pale pink color. To calculate the molarity of NaOH‚ the following equation was used MNaOH x VNaOH = MKHP x VKHP therefore the molarity was .125 M. INTRODUCTION This lab experiment covers the preparation of standard solution and the acid/base titration. The first part of the lab is to prepare a standard solution of Potassium hydrogen per. A standard solution is a solution of known concentration‚ in which it is prepared using exacting techniques to make sure that the molarity
Premium Sodium hydroxide Titration
Moment of Inertia and Rotational Motion Garret Hebert PHY 2311 Tues 1:00 garret.hebert@hindscc.edu Abstract: During this lab we will study what rotational Inertia is and how different shapes of masses and different masses behave inertially when compared to each other. We will specifically study the differences of inertia between a disk and a ring. We will use increasing forces to induce angular acceleration of both a disk and a ring of a certain mass. We will then then measure the differences
Premium Classical mechanics Inertia Torque
Department of Chemical Engineering CHME 426 –Chemical Engineering Laboratory III Title Page (Full Report) Title of the Experiment: Reaction through three CSTR in series Submitted by: Group (4) Section: Female 1. Name: Amina Ali ID: 200550284 2. Name: Duaa Tabarak ID: 200553858 3. Name: Mariam Rustom ID: 200552242 Date of experiment: 31st March‚ 2010 Date of submission: 11th April‚ 2010 Grades: Report presentation………………………………………… /15 Abstract and Objective(s)……………………………………/10
Premium Sodium hydroxide Chemical reaction