Conclusion and Evaluation Conclusion In our test we put six different sliced up potatoes chips in solutions. The solution was different concentration of salt and water‚ one was 5% sugar‚ one 10%‚ one 15%‚ one 20% and one 30% salt concentration. We measured the mass of the potatoes chip before and after we put it into the solution. To keep the experiment fair we only changed one variable which was the salt concentration. The results that we got showed the chip went up in mass for 0%
Premium Concentration Potato Potato chip
Conclusion In this experiment‚ we measured the mass of 4 gasses; oxygen‚ carbon dioxide‚ helium‚ and lab gas. We took a Ziplock bag‚ and turned into a non-stretchy balloon‚ and filled with each gas and measured the apparent mass then calculated the actual mass‚ then find a ratio between the mass of oxygen and the other gasses. We tried to keep the pressure about the same each time so our calculations would be more accurate. We found out that the heaviest was carbon dioxide‚ and the lightest
Premium Oxygen Carbon dioxide
Conclusion The purpose of this experiment was to discover the chemical properties that copper has when reacting with other chemicals and how it changes physically during these processes. (Department of Chemistry‚ 2013) This was achieved through many types of reactions‚ such as a redox reaction‚ double displacement‚ decomposition reaction and single displacement depending on the chemical properties in relation to copper of the other substances when it was added with copper. Copper was either in an
Premium Chemistry Chemical reaction
EXPERIMENT 5 REDOX TITRATION: TITRATION USING SODIUM THIOSULPHATE Objectives 1. 2. To prepare a standard solution of potassium iodate for use to determine the concentration of sodium thiosulphate solution accurately. To acquire the proper techniques of carrying out a titration. Introduction Redox titrations using sodium thiosulphate as a reducing agent is known as iodometric titration since it is used specifically to titrate iodine. The reaction involved is: I2 + 2Na2S2O3 I2 + 2S2O322NaI + Na2S4O6
Free Titration Iodine
have been taken in the experiment. There is five safety factors that should be taken while doing the experiment in laboratory: Make sure our hands are dry when switch on the switch of the machine Make sure the turbine is not stopped immediately as it tends to overspeed with emergency stops. Make sure the equipment function well before experiment get started. Must follow procedure going on the experiment so accident could be avoid during experiment. Make sure handling
Premium Hydroelectricity Water turbine Water wheel
Barry Allahyar Dr. Dodd CHEM 2122 2010-09-16 Experiment 19: Fischer Esterification‚ Conclusion The objective in this experiment was to efficiently perform an Fischer esterification of 1-butanol and acetic acid to form water and n-butyl acetate‚ and to confirm the esterification using IR spectroscopy analysis. It was found that 0.734 grams of n-butyl acetate was formed with a percent yield of 61%. The product was confirmed using IR spectroscopy and boiling point confirmation. The reaction mechanism
Premium Acetic acid Alcohol Ester
Alum Lab Conclusion The purpose of this laboratory was to use two different techniques to attempt to identify the melting point and the mole ratio of hydrated water to anhydrous aluminum‚ potassium‚ and sulfate of AlKSO4. The hypotheses were: if the alum was put in a capillary tube the melting point of alum will be able to be determined; and the water of hydration in alum crystals will be possible to determine if the alum is heated with a Bunsen burner. Results: Part 1: Data Table | Trial
Premium Chemistry
In conclusion to the distillation lab‚ I think our data shows that our experiment went well. Our graph resembles the graph in the lab handout (graphs attached to lab notebook sheets). The fractional distillation shows the sharp slope between when the cyclohexane burns off and mostly only toluene remains. The microscale graph seems to be accurate because it shows the large jump where the cyclohexane is burned off. To view the apparatuses used in the experiment look at the attached pictures. To
Premium Distillation
In conclusion‚ after conducting the lab‚ the emergent properties of water were tested and proved. These trials and experiments were able to verify the adhesion‚ cohesion‚ polarity‚ temperature stabilization‚ solvency‚ and density changes exhibited by water. During the glass and wax paper lab‚ we observed the adhesive properties of water. When a droplet of water touched the glass‚ it dispersed immediately. The droplet placed on the wax paper remained intact and in droplet form. Also‚ when the
Premium Water Atom Oxygen
Lab Conclusion on Density In the lab of measuring density‚ precision and accuracy are very key components. Precision is the exactness of a measurement or good technique. Now accuracy is the value that we measured compared to the true value that the book has. Precision and accuracy are important because you need to have good technique and have your value close to the true value to minimize the error analysis. If you do these steps correctly you are a good chemist but if you do them poorly they
Free Measurement Volume Length