to observe a shift in equilibrium concentrations associated with changes in temperature 4. to explain the observations obtained by applying Le Chatelier’s principle Materials Required: See page 209 Heath Chemistry Laboratory Experiments Procedure: See pages 209-211 Heath Chemistry Laboratory Experiments Data and Observations: Table 1 Equilibrium Involving Thymol Blue REAGENT ADDED STRESS (ION ADDED) COLOR OBSERVATION DIRECTION OF EQUILIBRIUM SHIFT HCl (Step
Premium Chemistry Experiment Hypothesis
October 13‚ 2012 Needle through a Balloon Pre-Lab Preparations: Purpose: The purpose of this experiment is to see if the balloon pops when pierced with a wooden skewer or a sharp pin. Hypothesis: If we lubricate the skewer with petroleum jelly‚ then it should go through the balloon without popping. Hypothesis for the 2nd part of the Lab: If we cover the side of the balloon with cellophane tape‚ then it will not pop when pierced with the pin. Materials: • Balloons • Long wooden
Premium Hypothesis Observation Stanford prison experiment
Jashandeep Gill Gammellos Chemistry Density is one of the fundamental principles of physics. Density is the reason why a plank of wood floats on water while a piece of metal several times smaller will sink. Density of an object is measured in g/cm³ or g/cc. The equation is D=M/V‚ D being the density of the object‚ M being the mass of the object‚ and V being the volume of the object. Mass is the space an object takes up. It is the amount of matter present in an object. Mass is measured using
Free Density Water Kilogram
Procedure Access the virtual lab and complete the experiments. Part One (Flame Test): 1. Create and complete a data table for Part One of the lab. It should include the name of the element (or unknown) examined and the color of the observed flame: Barium-green Calcium-red Sodium-yellow Rubidium-purple Potassium-blue Lithium-pink 2. Identify each unknown from Part One of the lab and briefly explain why you identified each unknown as you did.: Unknown 1-yellow. I think it is Sodium because
Premium Light Atom Color
Physical and Chemical Change Objective: Recognize and distinguish between chemical and physical changes. Materials: - lab balance - microspatula - lab burner - dropper pipet - 5 test tubes - mortar and pestle - test tube rack - magnet - test tube holder - insulating pad - watch glass - safety goggles - glass square - lab apron or coat - copper sulfate pentahydrate - iron fillings - sodium chloride - magnesium ribbon - hydrochloric acid - paper
Premium Chlorine Mixture Sulfuric acid
Regents Chemistry Quarter 1 Midterm Review 1. The percent by mass of oxygen in Na2SO4 (formula mass = 142) is closest to 1) 11% 3) 45% 2) 22% 4) 64% 2. Given the unbalanced equation: __Al(s) + __O2(g) → __Al2O3(s) 3. 4. 5. 6. 7. balance the equation using smallest whole number coefficients. The percent by mass of aluminum in Al2O3 is approximately 1) 18.9 3) 47.1 2) 35.4 4) 52.9 What is the approximate percent composition by mass of CaBr2 (formula mass = 200)
Premium Water Ideal gas law Melting point
Buffers CALCULATIONS Table A. pH Measurement using pH meter Calculated pH Solution 1 – HoAc 0.10 M CH3COOH CH3COOH + H2O ⇌ CH3COO- + H3O+ i 0.10 ø ø c -x +x +x e 0.10 – x x x Ka = H3O+[CH3COO-]CH3COOH = x20.10 – x = 1.8 x 10-5 x = 1.33 x 10-3 M pH = -log [1.33 x 10-3] pH = 2.88 Solution 2 – HoAc – OAc
Free PH Acid dissociation constant Buffer solution
INTRODUCTION: The purpose of this experiment is to measure the formation constant of the tetraamminecopper(II) ion by colorimetry. Anhydrous copper sulfate (CuSO4) is white‚ which means that it does not absorb light in the visible region of the spectrum. The hydrated copper sulfate (CuSO4 - 5H2O) is blue. The structure of the compound can be represented more accurately as Cu(H2O)4 SO4 - H2O where four water molecules are bound to the copper ion and the fifth is a water of crystallization. The
Premium Ammonia Chemistry Copper
Discussion The purpose of the Density Lab was to determine the identity of four unknown solids and two unknown liquids by calculating their densities and comparing them to a density chart‚ taking into account error analysis and finally classifying the substances. In order to calculate this density‚ we first found the mass of the container that was to be holding the substances. We then found the volume of the substance‚ and lastly determined the mass of the container and substance. We subtracted
Premium Liquid Density Volume
examine the effectiveness of buffers by titrating two sets of five different solutions using HCl and NaOH and monitoring the pH change of the various solutions. The data collected shows that the buffer systems made with sodium acetate and acetic acid were effect when titrated with the strong acid and the strong base. Comparison of all the solutions shows that the concepts of buffers holds true for the results from the experimentation. Introduction The main objective of this lab was to test the ability
Premium Acid dissociation constant PH Buffer solution