Experiment #1: Mass‚ Volume and Density Performed: 2/2/11 Turned in: 2/9/11 The purpose of this experiment is to verify the independence of X and Y motion for a projection. We watch the professor perform this experiment. The equipment used in this experiment was a projectile launcher (ME-6800)‚ a drop shoot accessory (ME-9859)‚ one photogate (ME-9204A)‚ white paper‚ carbon paper‚ two time-of-flight timing pad (ME-6810)‚ two balls (ball 1 and ball 2)‚ and an interface computer. Ball 1 is dropped
Premium Test method Mass Force
Experiment 12: Calorimetry and Hess’s Law Purpose: The purpose of this lab is to determine the enthalpy of reaction for the burning of one mole of magnesium in oxygen. Although the reaction is exothermic‚ the ∆HRXN will be determined by using calorimetry and then using Hess’s Law to manipulate the data collected to yield the answer needed. Procedures: Dillon‚ Stephanie. “ Calorimetry and Hess’s Law.” Laboratory Manual. Pearson Publishing‚ 2012‚ pp.168-177. Data and Results Part A
Free Enthalpy Thermodynamics
Discussion The purpose of the Density Lab was to determine the identity of four unknown solids and two unknown liquids by calculating their densities and comparing them to a density chart‚ taking into account error analysis and finally classifying the substances. In order to calculate this density‚ we first found the mass of the container that was to be holding the substances. We then found the volume of the substance‚ and lastly determined the mass of the container and substance. We subtracted
Premium Liquid Density Volume
SCIENCE Density Calculate density‚ and identify substances using a density chart. Density is a measure of the amount of mass in a certain volume. This physical property is often used to identify and classify substances. It is usually expressed in grams per cubic centimeters‚ or g/cm3. The chart on the right lists the densities of some common materials. EQUATION: Densities of Substances Substance Density (g/cm3) Gold 19.3 Mercury 13.5 Lead mass density ϭ ᎏ volume
Premium Density Volume Water
Soil Porosity & Density Objective: To determine if the porosity of soil is related to the density. Hypothesis: I think that that the porosity of soil is related to the density because the higher the density of the sand the lower the porosity of the sand‚ which are both componets for the water to rise. Materials: • Sand and Loam samples • 2 large containers • Plastic cups • Water • Scale Procedure: Loam 1) The loam without the water was fresh ‚ it had different shades of black‚ and
Premium Soil Density Sand
solution Red-Orange Ni(NO3)2 Transparent‚ blue Green-Blue Unknown A Colourless solution Green Unknown B Colourless solution Light Purple Unknown C Colourless solution Bright Orange Unknown D Colourless solution Dark Red Questions: 1. Unknown A Ba(NO3)2 Unknown B KNO3 Unknown C NaCl (aq) Unknown D Sr(No3)2 2. The ranking would be as follows: Sr(NO3)2 ‚ LiNO3‚ Ca(NO3)2‚ NaNO3‚ Solid NaCl‚ NaCl‚ Ba(NO3)2‚ Cu(NO3)2‚ Ni(NO3)2 and lastly KNO3. 3. Most of the anions are
Premium Color Potassium Solid
Density of a regular shaped object Object Mass / g ± 0.05 g * Length / cm ± 0.003 cm ** Width / cm ± 0.003 cm ** Height / cm ± 0.003 cm ** T1 T2 T3 T4 T5 T1 T2 T3 T4 T5 T1 T2 T3 T4 T5 A 44.9 5.975 5.980 5.980 5.980 5.975 1.500 1.500 1.500 1.500 1.500 0.600 0.600 0.605 0.600 0.600 B 16.5 4.400 4.395 4.400 4.395 4.395 1.500 1.500 1.495 1.500 1.495 0.300 0.305 0.305 0.300 0.300 C 22.5 3.000 2.995 3.000 3.000 3.000 1.500 1.505 1.495 1.500 1.500 0.600 0.595 0.600 0.595 0.595 D 22.6 6.005 6
Premium Measurement Error Length
Chemistry 121 Colligative Properties Lab Demonstration of Selected Calculations from Choice I Determination of Kf for Naphthalene To determine the Kf for naphthalene‚ we need to find the difference in the freezing point of pure naphthalene and the solution of 1‚4-dichlorobenzene in naphthalene. Let’s say that we did this experiment‚ used 1.00 g 1‚4-dichlorobenzene in 10.00 g naphthalene‚ and found that the freezing temperature of pure naphthalene was 78.2°C‚ while that of the solution was 75
Premium Chemistry Atom Oxygen
The purpose of this lab was to see which solutions are soluble and which are not. We were able to see this by mixing certain solutions together and observing changes that occurred. The procedure for this experiment included a few different steps. The first steps were to add the nitrate solutions into the lettered parts of the 96-well plate. Once you were done with that‚ you were supposed to add the sodium solutions to the numbered parts of the 96-well plate‚ so that the solutions were added together
Premium Ion Solubility Chemistry
Student: Keila Dukuze Date: Feb/10/2013 Lab# 3 Section: 110 Pre-Lab Report Determining the Density of Various Liquids and Solids The purpose of this experiment is to determine the weight (density) of certain liquids and solids in chemistry. These liquids include; Water‚ Hexane‚ Carbon Tetrachloride‚ and solids include; Copper‚ Zinc‚ Lead and‚ Aluminum. It’s important to know the weight of these products so you can properly conduct experiments and make clear observations. Different
Premium Liquid Temperature Accuracy and precision