Your Name NETW202‚ Professor’s Name Current Date Lab #3 Lab Report Section I: Watch the videos on the UTP cabling‚ read your course material and answer the questions below. Add in graphics from the internet to enhance your answers and be sure to cite your references. (Each question is worth 1 point each) 1.What is meant by the term “pinout”? 2.What are the following cable types used for and how are they made? How are they different? Crossover cable Rollover cable Straight through cable
Premium Transmission Control Protocol Twisted pair
Computer Networking: A Top-Down Approach Featuring the Internet‚ 4th Edition Solutions to Review Questions and Problems Version Date: June 21‚ 2007 This document contains the solutions to review questions and problems for the 4th edition of Computer Networking: A Top-Down Approach Featuring the Internet by Jim Kurose and Keith Ross. These solutions are being made available to instructors ONLY. Please do NOT copy or distribute this document to others (even other instructors). Please do not post
Premium Transmission Control Protocol
Question Bank on Internet Technology Specially designed for Sixth Semester B.Sc. (IT) Students These notes are prepared for student’s personal use. Any commercial use of this material is strictly prohibited. Guide to solution code |Sr. No. |Chapter | |Starting with: |
Premium Transmission Control Protocol User Datagram Protocol
receiver should request next one which is 3. If assume there is 8 sequence numbers N=0‚ 1‚ 2‚3‚4 so the size of transmitter sliding window is (2N -1). Receiver is not going to get frame 7 till sender get the “Ack” of frame 0 otherwise if we send all 0 to 4 and by the accident sender could not get the”Ack” of frame 0 when the timer expires frame 0 will be retransmitted and since receiver’s window is pointing to the next 0-4 frames and expecting new frame 0‚ is going to take it as the new frame0 which is
Premium Transmission Control Protocol OSI model Radio
/ RPL 6LoWPAN CSMA / link-layer bursts ContikiMAC IEEE 802.15.4 A Low-Power CoAP for Contiki 2 ContikiMAC Radio on D Data frame A ACK frame Sender D D D D A Receiver Channel check D A Transmission detected Matthias Kovatsch – ETH Zürich A Low-Power CoAP for Contiki 3 Link-layer Bursts Radio on D Data frame A ACK frame Sender D D D D A D A D A D A Receiver Channel check D A D A D A D A Transmission detected Matthias Kovatsch
Premium OSI model
Data Transport in Wireless Networks Akinniyi Ojo‚ Alireza Ranjbar‚ Bastian Arjun Shajit‚ Behzad Savabi‚ Misikir Gebrehiwot‚ Robin Babujee Jerome‚ Setareh Roshan‚ Swapnil Pande Department of Communication Engineering‚ Aalto University School of Electrical Engineering‚ Espoo‚ Finland Abstract— The popularity of wireless networks used to access the Internet is increasing immensely. With huge advancements in the field of wireless technology‚ the Internet has slowly moved from a traditional wired
Premium Transmission Control Protocol
EVN|A04|200605221309 PID|1||M000001327||TEST^RECURRING^^^^||19680215|F|^^^^^||^^^^|||||||L000029512|74 DG1|1|TX||PROTIMES PV1|1|O|RCA^^||||HARR^HARNER^ROBERT|HARR^HARNER^ROBERT||||||||||RCR||U|||| • The receiving system will acknowledge the message using an ACK Message:
Premium Internet Protocol Suite Transmission Control Protocol Internet
Universal Serial Bus Specification Compaq Hewlett-Packard Intel Lucent Microsoft NEC Philips Revision 2.0 April 27‚ 2000 Universal Serial Bus Specification Revision 2.0 Scope of this Revision The 2.0 revision of the specification is intended for product design. Every attempt has been made to ensure a consistent and implementable specification. Implementations should ensure compliance with this revision. Revision History Revision Issue Date Comments 0.7 November
Premium Universal Serial Bus
UNIT II- Peripherals and Interfacing PIO 8255 The parallel input-output port chip 8255 is also called as programmable peripheral input-output port. The Intel’s 8255 is designed for use with Intel’s 8-bit‚ 16-bit and higher capability microprocessors. It has 24 input/output lines which may be individually programmed in two groups of twelve lines each‚ or three groups of eight lines. The two groups of I/O pins are named as Group A and Group B. Each of these two groups contains a subgroup of eight
Premium Output Input/output
CALL & MOBILITY MANAGEMENT Connection Management What is Connection Management ? Connection Management enables different CM sub-layer entities to communicate with their pier entity using different MM connections. Different CM sub-layer entities use different MM connections. Different MM connections are identified by Protocol Discriminator PD and‚ additionally by Transaction Identifier TI. Mobile To Land Call Set-up Scenario Phases of Mobile To Land Call ( Mobile Originated Call- MO Call
Premium Radio Mobile phone Mobile River