Lab Report 3 In this lab‚ we will take a trip to the planetarium lab and will learn about Right ascension and declination‚ and altitude and zenith. After looking at the different points shown‚ we will log the altitude and zenith in the chart in our lab manual. Now we will look at the same points and label the right ascension and declination. Then we will learn about the easiest way to locate the star Polaris. As we started the first program‚ we answered a few questions to make sure we knew
Premium
This lab report will be detailing the steps taken and the results discovered when using spectrophotometry to determine the percentage of copper in a copper-clad penny and the thicknes of the copper layer on the copper-clad penny. After 1982‚ copper coating has been used in the creation of the penny because the cost of pure copper has increase to the point that the amount needed t omake a penny cost far more than the actual value of the penny. This lab allowed us to see just how much copper coating
Premium Chemistry Spectroscopy Ammonia
LSM1102 Lab Report Introduction Transformation is a process which involves plasmid DNA being bound to the cell surface and the subsequent uptake of DNA by the cell (Panja et al.‚ 2008). For artificial transformation of E. coli cells with plasmids‚ plasmid DNA has to be extracted from bacterial cells using the High-Speed Plasmid Mini Kit‚ which is then mixed with competent E. coli cells followed by heat shock and the streaking of transformed cells on two different types of agar plate (LB and LB+ampicillin)
Premium Plasmid Transformation Escherichia coli
MEC 325/580 Lab Report CNC Machining Lab Report Date: March 18‚ 2013 Group Leader: Jian Wu Team Members: Group Number: G4 Regment No.: D Insturctor: CONTENTS 1.Objective and introduction. 2.Principles and practice. 3.Design and result. 4.Conclusion and recommendations. Appendices 1. Objective and introduction * Objectives Operate the CNC milling machine using G-codes‚ M-codes in a CNC program. * Equipment: Minitech CNC machine (Series 2) * Machine
Premium Milling machine Numerical control
Unknown Lab Report Dr. Nathan Cahoone Microbiology 204 December 9‚ 2010 Introduction There are many reasons for knowing the identity of microorganisms. The study and test was done by applying all of the methods that have been learned so far in the microbiology laboratory class for the identification of an unknown bacterium which I was using unknown #25. Results Unknown #25 had the following morphology on a streak plate: medium sized butyrous cream colored colony. Gram-staining was utilized
Premium Bacteria Gram staining Microbiology
Lab #4: The Immune System Purpose: The purpose of this lab was to perform and understand the procedures of conducting an ELISA test to determine whether a particular antibody is present in a patient’s blood sample through a virtual simulation. Hypothesis: If I successfully complete this lab‚ I will then understand how to perform an ELISA test‚ the purpose an ELISA test‚ and also how to interpret the results of this test. Materials and Procedures: Materials: Howard Huges medical
Premium Antibody Immune system Immunology
Bubble Inside a Bubble Materials • • • • • • • • Granulated sugar (we had our best results using Imperial Sugar and Dixie Crystals) Dish soap Water Tablespoon Scissors Pipette Cup Adult supervision Bubbles form because of a combination of water’s hydrogen bonds and the oily film you can see shimmer in the light. The oily film you see is actually two separate layers of soap attached to‚ and surrounding‚ hydrogen-bonded water. Solar Oven S’mores Materials • Pizza box • Two clear sheet protectors
Premium Oxygen Thermodynamics Water
Lab Report Abstract: The purpose of this lab was to see how magnesium reacts with oxygen. This reaction must be forced with heat. As magnesium changes to magnesium oxide the mass increased. Procedure: 1. Set up the stand and bunsen burne. 2. Go to crucible heat oven to obtain a crucible. 3. Weigh the crucible and lids mass. 4. Break up the magnesium ribbon on the crucible and weigh the mass of the magnesium‚ crucible‚ and lid. 5. Place the crucible on the ring stand over the flame. Allow
Free Force Mass Oxide
Lab Report – Strong Example Problem/Question Does using a base coat before painting nails prevent chipping? Background Information When painting nails‚ some manicurists use a base coat before applying the polish. The purpose of a base coat is to help the polish stick to your nails more easily. Base coats also help to protect your natural nail from the staining effects of colored polishes. Ridge-filling base coats fill in the grooves and cracks in the nail to create a smoother appearance
Premium Left-handedness French Revolution Handedness
Lab Report Janice Chisholm SCI207: Dependence of Man on the Environment Instructor: Lee Ott April 28‚ 2013 1. What patterns do you observe on the information table 4? While observing the information in table 4‚ it appears that the number of fish changes from time to time and the oxygen increases and / or decreases when this occurs. 2. Develop a hypothesis relating to the amount of dissolved oxygen measured in the water sample and the number of fish observed in the body of water?
Free Observation Scientific method Hypothesis