Preview

mr ali

Powerful Essays
Open Document
Open Document
23470 Words
Grammar
Grammar
Plagiarism
Plagiarism
Writing
Writing
Score
Score
mr ali
ARTICLE IN PRESS

Progress in Aerospace Sciences 42 (2006) 85–128 www.elsevier.com/locate/paerosci The aerodynamics of propellers
Quentin R. WaldÃ
102 Cape George Road, Port Townsend, WA 98368, USA

Abstract
The theory and the design of propellers of minimum induced loss is treated. The pioneer analysis of this problem was presented more than half a century ago by Theodorsen, but obscurities in his treatment and inaccuracies and limited coverage in his tables of the Goldstein circulation function for helicoidal vortex sheets have not been remedied until the present work which clarifies and extends his work. The inverse problem, the prediction of the performance of a given propeller of arbitrary form, is also treated. The theory of propellers of minimum energy loss is dependent on considerations of a regular helicoidal trailing vortex sheet; consequently, a more detailed discussion of the dynamics of vortex sheets and the consequences of their instability and roll up is presented than is usually found in treatments of propeller aerodynamics.
Complete and accurate tables of the circulation function are presented. Interference effects between a fuselage or a nacelle and the propeller are considered. The regimes of propeller, vortex ring, and windmill operation are characterized. r 2006 Elsevier Ltd. All rights reserved.

Contents
1.

2.

3.

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
1.1. Present status of propeller aerodynamics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
1.2. Historical development of propeller theory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Basic principles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
2.1.



References: [3] Drzewiecki S. Bulletin de L’Association Technique Maritime, Paris. A Second Paper in 1901, 1892. AIAA Paper 2001-3386, Joint Propulsion Conference, Salt Lake City, 2001. [5] Betz A. with Appendix by L. Prandtl, 1919, Schraubenpropeller mit Geringstem Energieverlust, Gottinger Nachrich¨ ten, Gottingen, p David Taylor Model Basin, Report 1534, Applied Mathematics Laboratory, Washington, DC, 1964. [10] Larrabee EE. Practical design of minimum induced loss propellers, SAE Technical Paper 790585, 1979. 2299, Supt. of Documents, US Gov’t Printing Office, 1967. State University, Nord 16597-5, 1956. Meeting, New York, 1964. Meeting, Society of Naval Architects and Marine Engineers, New York, November 17–20, 1982.

You May Also Find These Documents Helpful

  • Good Essays

    M4 Study Guide

    • 1238 Words
    • 5 Pages

    A propeller rotating clockwise, as seen from the rear, creates a spiraling slipstream that tends to rotate the aircraft to the…

    • 1238 Words
    • 5 Pages
    Good Essays
  • Better Essays

    The objective of this exercise is to measure the pressure distribution across the surface on an aerofoil in a wind tunnel. The aerofoil is tested under several different Mach numbers from subsonic to supercritical. The purpose of measuring the pressure distributions is to assess the validity of the Prandtl-Glauert law and to discuss the changing chracteristics of the flow as the Mach number increases from subsonic to transonic.…

    • 2069 Words
    • 9 Pages
    Better Essays
  • Better Essays

    introduction

    • 5346 Words
    • 41 Pages

    Anderson JD Jr. 1997. A History of Aerodynamics and Its Impact on Flying Machines. London: Cambridge Univ. Press.…

    • 5346 Words
    • 41 Pages
    Better Essays
  • Powerful Essays

    The function of a propeller on an aircraft is to provide propulsive force. This lab report was aimed at studying and analysing the propeller and some engine properties of a Cessna 310R. The axial momentum theory, advance ratio and the energy method for fuel flow estimation are used in this analysis.…

    • 1475 Words
    • 6 Pages
    Powerful Essays
  • Powerful Essays

    Abstract The problem discussed in this report is how lift is truly generated on an aerofoil and also explaining the misconceptions of lift and why they are not correct. Further topics discussed are the Lift is a force that directly opposes the weight of an aircraft and holds the object in air. Since lift is a result of the thrust or motion of the aircraft it is therefore a force (vector) because it has a magnitude and a direction. But lift cannot be achieved without thrust.…

    • 2036 Words
    • 9 Pages
    Powerful Essays
  • Good Essays

    Left Turning Tendencies

    • 530 Words
    • 3 Pages

    As the propeller creates thrust and produces a backwards flow of air, or slipstream, the air “wraps” around the airplane. Since there is a clockwise rotation of the propeller, the resultant slipstream flows over the top of the fuselage back around and underneath, then comes around to strike the left side of the vertical stabilizer. Which then yaws the aircraft to the left. As airspeed is increased, the slipstream tends to “stretch” out and the left turning force is less apparent.…

    • 530 Words
    • 3 Pages
    Good Essays
  • Good Essays

    Speed Boat

    • 340 Words
    • 2 Pages

    Materials used in this project are: Simple Switch, Electric Motor, Battery Holder, Propeller, wire, Styrofoam cup, Popsicle stick…

    • 340 Words
    • 2 Pages
    Good Essays
  • Better Essays

    Aerodynamics of a Baseball

    • 1424 Words
    • 6 Pages

    We will discuss several different pitches and how the Magnus force acts on each of the pitches. Additionally we will discuss how this Magnus force can be used in a practical application to aviation…

    • 1424 Words
    • 6 Pages
    Better Essays
  • Powerful Essays

    decided to be different from the common design, giving two propeller power at a given single motion. The control…

    • 1079 Words
    • 5 Pages
    Powerful Essays
  • Good Essays

    A client of Andrews Timber Furnishing is in need of some sort of table to sit coffees on. This comes about after her house was flooded earlier this year.…

    • 1814 Words
    • 8 Pages
    Good Essays
  • Powerful Essays

    Propeller

    • 2442 Words
    • 10 Pages

    Bibliography: Edwards J.D. (1991) “Electrical machines and drives : an introduction to principles and characteristics.”…

    • 2442 Words
    • 10 Pages
    Powerful Essays
  • Good Essays

    Yarn structure is one of the primary factors which control the properties of spun yarns. Vortexspun…

    • 1894 Words
    • 8 Pages
    Good Essays
  • Powerful Essays

    Ship

    • 5161 Words
    • 21 Pages

    ITTC – Recommended Procedures and Guidelines Testing and Extrapolation Methods Propulsion, Performance Propulsion Test 7.5-02 -03-01.1 Page 1 of 14 Effective Date 2002 Revision 01 Table of Contents 1 2 3.3.2.1 Propeller Thrust .............................7 3.3.2.2 Propeller Torque ............................7 3.3.3 External Tow Force.......................7 3.3.4 Rate of revolution..........................8 3.3.5 Sinkage and trim ...........................8 3.3.6 Speed .............................................8 3.3.7 Thermometer .................................8 PURPOSE OF PROCEDURE .............2 PARAMETERS .....................................2 2.1 Data Reduction Equations.................2 2.2 Definition of Variables....................... 2 3 DESCRIPTION OF PROCEDURE ....3 3.1 Model and Installation.......................3 3.1.1 Models...........................................3 3.1.1.1 Hull Model ..................................... 3 3.1.1.2 Propeller/Propulsion Unit Model 3.4 Test Procedure and Data Acquisition8 3.4.1 Methods.........................................8 3.4.1.1 Load Varying (or Constant Speed) Method ...............................8 3.4.1.2 Constant Loading Method ..........8 3.4.1.3 Mixed Loading Method...............9 3.4.2 General Remarks ...........................9 3.4.3 Skin friction correction force ........9 3.4.4 Measured Quantities....................10 3.4.5 Shaft Tare Test ............................10 3.4.6 Correction to Measured Forces ..........................................11 3 3.1.2 Installation.....................................4 3.1.2.1 Hull Model ..................................... 4 3.1.2.2 Propeller/Propulsion Unit Model ............................................... 4 3.1.3 Measurement Systems..................4 3.2 Instrumentation..................................4 3.2.1 Thrust ............................................4 3.2.2…

    • 5161 Words
    • 21 Pages
    Powerful Essays
  • Powerful Essays

    This project is developed for the users to rotate the back wheel of a two wheeler using propeller shaft. Usually in two wheelers, chain and sprocket method is used to drive the back wheel. But in this project, the Engine is connected at the front part of the vehicle. The shaft of the engine is connected with a long rod. The other side of the long rod is connected with a set of bevel gears. The bevel gears are used to rotate the shaft in 90o angle. The back wheel of the vehicle is connected with the bevel gear(driven). Thus the back wheel is rotated in perpendicular to the engine shaft. Thus the two wheeler will move forward. According to the direction of motion of the engine, the wheel will be moved forward or reverse. This avoid the usage of chain and sprocket method.…

    • 1288 Words
    • 6 Pages
    Powerful Essays
  • Satisfactory Essays

    Induction Motor

    • 282 Words
    • 2 Pages

    With the advent of electrical energy distribution systems and their universal adoption throughout the world for the purpose of lightening and power the field of electric motors especially the AC type has shown a remarkable development in all prospects all over the world. As a result of the technological advancements the engineers throughout the world tried their best of best to come out with the most energy efficient and safe machines particularly, in the context of electric motors.…

    • 282 Words
    • 2 Pages
    Satisfactory Essays