Metalurgical
PACIFIC TESTING LABORATORIES, INC.
24950 Avenue Tibbitts, Valencia, CA 91355-3426, USA • TEL (661) 257-1437 • FAX (661) 257-2411
TEST REPORT
In Account With
SEMCO INSTRUMENTS, INC.
25700 Rye Canyon Road
Valencia, CA 91355-1148
Date
Page 1 of 5 Pages
Specification
None
P.O. No.
102524-00
Attn: Christopher Do
June 2, 2014
W.O. Number
51348
Received
05-22-14
IDENTIFICATION : One (1) “intact probe tip” from PTL W/O 51105 (P/N
TC53900 Rev NS) was submitted for testing in accordance with the customer specified requirements.
SPECIFICATION : Not Specified.
REFERENCE
: Purchase Order Number 102524-00.
TESTING
: Microsection Examination.
SUMMARY
: The test results, reported herein, are submitted for customer evaluation.
Respectfully submitted,
PACIFIC TESTING LABORATORIES, INC.
Hans Shin
Materials Engineer
This report applies only to the sample(s) tested and is not necessarily indicative of the quality or condition of apparently identical or similar products. As a mutual protection to clients, the public and Pacific Testing Laboratories, Inc., this report is submitted and accepted for the exclusive use of the client to whom it is addressed and upon the condition that it is not to be used, in whole or in part, in any advertising or publicity matter without prior written authorization from Pacific Testing Laboratories, Inc.
TESTING · ENGINEERING · RESEARCH & DEVELOPMENT
Page No. : 2 of 5
W/O No. : 51348
MICROSECTION EVALUATION
REFERENCE
: PTL W/O 51105.
REQUIREMENT : None.
TEST METHOD : The sample was microsectioned and mounted using a two-part expoxy resin system according to PTL’s standard procedures.
After room temperature curing of the mounting resin, the mount was ground using 240, 320, 400, and 600 grit silicon metallurgical paper. It was then polished with 1.0 micron,
0.3 micron, and followed with 0.05 micron alumina polishing powder. The microsectioned sample was examined with a
24950 Avenue Tibbitts, Valencia, CA 91355-3426, USA • TEL (661) 257-1437 • FAX (661) 257-2411
TEST REPORT
In Account With
SEMCO INSTRUMENTS, INC.
25700 Rye Canyon Road
Valencia, CA 91355-1148
Date
Page 1 of 5 Pages
Specification
None
P.O. No.
102524-00
Attn: Christopher Do
June 2, 2014
W.O. Number
51348
Received
05-22-14
IDENTIFICATION : One (1) “intact probe tip” from PTL W/O 51105 (P/N
TC53900 Rev NS) was submitted for testing in accordance with the customer specified requirements.
SPECIFICATION : Not Specified.
REFERENCE
: Purchase Order Number 102524-00.
TESTING
: Microsection Examination.
SUMMARY
: The test results, reported herein, are submitted for customer evaluation.
Respectfully submitted,
PACIFIC TESTING LABORATORIES, INC.
Hans Shin
Materials Engineer
This report applies only to the sample(s) tested and is not necessarily indicative of the quality or condition of apparently identical or similar products. As a mutual protection to clients, the public and Pacific Testing Laboratories, Inc., this report is submitted and accepted for the exclusive use of the client to whom it is addressed and upon the condition that it is not to be used, in whole or in part, in any advertising or publicity matter without prior written authorization from Pacific Testing Laboratories, Inc.
TESTING · ENGINEERING · RESEARCH & DEVELOPMENT
Page No. : 2 of 5
W/O No. : 51348
MICROSECTION EVALUATION
REFERENCE
: PTL W/O 51105.
REQUIREMENT : None.
TEST METHOD : The sample was microsectioned and mounted using a two-part expoxy resin system according to PTL’s standard procedures.
After room temperature curing of the mounting resin, the mount was ground using 240, 320, 400, and 600 grit silicon metallurgical paper. It was then polished with 1.0 micron,
0.3 micron, and followed with 0.05 micron alumina polishing powder. The microsectioned sample was examined with a