F645i
2006-2011 GSXR750 Z-Fi INSTALLATION INSTRUCTIONS
P/N F645
WARNING!
USE ONLY IN RACE OR OTHER CLOSED COURSE APPLICATIONS AND NEVER ON PUBLIC ROADS
Z-Fi products do not meet California CARB highway requirements
Z-Fi CONTROL UNIT
FUEL HARNESS
DOWNLOAD Z-Fi MAPPER SOFTWARE & ITS INSTRUCTIONS FROM WEBSITE
USB CABLE
SCOTCHLOK
SWINGARM STICKERS
O2 ELIMINATOR
(06-07 models do not have an O2 eliminator so this part will not be used and step 10 in these instructions will be skipped.)
The control unit supplied with this kit has been pre-programmed with two fuel maps. Map 1 is intended for use on 2008-2010 models and Map 2 for 2011 models. Note: A map for 2006-2007 models is available for download at www.Bazzaz.net.
9
7
8
1
2
6
3
4
5
(1) MAP SELECT
(2) ZAFM CONNECTORS
(3) SWITCHED POWER (RED TAG)
(4) LOWER INJECTORS (YELLOW TAG)
(5) UPPER INJECTORS
(6) GEAR POSITION
(7) THROTTLE POSTION SENSOR
(8) CRANK POSITION
(9) GROUND LUG
15330 Fairfield Ranch Rd., Unit E, Chino Hills, CA 92880 (909)597-8300 (909)597-5580 www.Bazzaz.net
WE STRONGLY SUGGEST THAT AN EXPERIENCED TECHNICIAN
INSTALL THIS BAZZAZ PRODUCT
1. Place the Z-Fi control unit in the tail section of the bike.
2. Route the fuel harness on the left hand side of the bike.
3. Plug the Z-Fi harness in-line with the lower injectors (yellow tag on harness is CYL # 1 lower injector).
WARNING! Make sure that the Z-Fi harness injector male pins make proper contact with the stock harness injector connectors.
4. Plug the Z-Fi harness in-line with the upper injectors (photo 1).
Photo 1
WARNING! Make sure that the Z-Fi harness injector male pins make proper contact with the stock harness injector connectors.
5. Plug the Z-Fi harness in-line with the primary/lower throttle position sensor and stock harness TPS connector
(photo 2).
Photo 2
6. Plug the Z-Fi harness in-line with the stock Crank Position Sensor connectors (photo 3).
Bazzaz CPS
Connectors
Stock CPS
Connectors
Photo 3
7. Plug the Z-Fi harness in-line with
P/N F645
WARNING!
USE ONLY IN RACE OR OTHER CLOSED COURSE APPLICATIONS AND NEVER ON PUBLIC ROADS
Z-Fi products do not meet California CARB highway requirements
Z-Fi CONTROL UNIT
FUEL HARNESS
DOWNLOAD Z-Fi MAPPER SOFTWARE & ITS INSTRUCTIONS FROM WEBSITE
USB CABLE
SCOTCHLOK
SWINGARM STICKERS
O2 ELIMINATOR
(06-07 models do not have an O2 eliminator so this part will not be used and step 10 in these instructions will be skipped.)
The control unit supplied with this kit has been pre-programmed with two fuel maps. Map 1 is intended for use on 2008-2010 models and Map 2 for 2011 models. Note: A map for 2006-2007 models is available for download at www.Bazzaz.net.
9
7
8
1
2
6
3
4
5
(1) MAP SELECT
(2) ZAFM CONNECTORS
(3) SWITCHED POWER (RED TAG)
(4) LOWER INJECTORS (YELLOW TAG)
(5) UPPER INJECTORS
(6) GEAR POSITION
(7) THROTTLE POSTION SENSOR
(8) CRANK POSITION
(9) GROUND LUG
15330 Fairfield Ranch Rd., Unit E, Chino Hills, CA 92880 (909)597-8300 (909)597-5580 www.Bazzaz.net
WE STRONGLY SUGGEST THAT AN EXPERIENCED TECHNICIAN
INSTALL THIS BAZZAZ PRODUCT
1. Place the Z-Fi control unit in the tail section of the bike.
2. Route the fuel harness on the left hand side of the bike.
3. Plug the Z-Fi harness in-line with the lower injectors (yellow tag on harness is CYL # 1 lower injector).
WARNING! Make sure that the Z-Fi harness injector male pins make proper contact with the stock harness injector connectors.
4. Plug the Z-Fi harness in-line with the upper injectors (photo 1).
Photo 1
WARNING! Make sure that the Z-Fi harness injector male pins make proper contact with the stock harness injector connectors.
5. Plug the Z-Fi harness in-line with the primary/lower throttle position sensor and stock harness TPS connector
(photo 2).
Photo 2
6. Plug the Z-Fi harness in-line with the stock Crank Position Sensor connectors (photo 3).
Bazzaz CPS
Connectors
Stock CPS
Connectors
Photo 3
7. Plug the Z-Fi harness in-line with