Ccna

Topics: IP address, Address Resolution Protocol, MAC address Pages: 7 (1059 words) Published: August 17, 2013
Module-1 Network Fundamental
1. How to create account in Academic Web Site.
2. Installation of Packet Tracer
3. Introduction of Packet Tracer.
4. Introduction of Network Devices
5. Services of Application Layer.(HTTP,DNS,SMTP,POP,DHCP) 6. Over view of ARP (Address Resolution Protocol)
7. Basic IOS.
Module-2 Routing Protocols and Concepts course
1. Static Routing
2. Routing Information Protocol (RIP) V1 & V2
3. Enhance Interior Gateway Routing Protocol (EIGRP)
4. Open Shortest Path First (OSPF)
5. Redistribution of Static route with RIP ,OSPF & EIGRP Module-3 LAN Switching and Wireless
1. Basic IOS of Switch
2. Port Security
3. VLANS
4. VTP
5. STP/RSTP
6. Inter-VLAN Routing
7. Wireless Configuration
Module-4 Accessing the WAN
1. PPP & HDLC
2. Frame Relay
3. ACLs
4. Nating & Pating and IPv6

How to create An account on Academic Web Site
Step 1: Go to the following link
https://auth.netacad.net/idp/Authn/NetacadLogin

Step 2: check your academic mail which is in your inbox.
Then write Cisco ID and password in academic website. (Note: Do not copy past)

Step 3: Update your profile on Cisco Academy site as shown below.

Step 4: Click on Yes, I am at least 18 years old.

Step 5: After successful completion of all steps accept the agreement.
And your Cisco Academy ID will be created.

Installation of Packet Tracer
Step 1: Double click on the “Packet Tracer .exe” file and start the setup by clicking NEXT.
Step 2: Click on I ACCEPT THE AGREEMENT and then NEXT

Step 3: Click NEXT to continue the Installation process

Step 4: Again click on NEXT

Step 5: Click on INSTALL to start the Installation

Step 6: Click FINISH to start the Packet Tracer wizard

Packet Tracer Wizard

Introduction of Packet Tracer.

How to Select a Router

How to Select a Switch

How to Select a Wireless Device

How to Select an End Device

How to Select a Cable

How to Access CLI of Router or Switch
Just double click on the device

Click on CLI to access the CLI mode

How to ON/OFF Simulation Mode

Introduction of Network Devices
NETWORK DEVICES SYMBOLS

Router
Switch

Wireless Router

Server

PC

Address Resolution Protocol (ARP)

Assign IP address to all devices and then Ping from PC0 to Server0. As Switch have no MAC table so Switch will broadcast ARP request to get MAC addresses of connected devices as shown below:

Click on the Switch PDU which shows that Switch broadcast the ARP request with the broadcast MAC address ffff.ffff.ffff, as shown in the following figure:

After the broadcast, Server will reply of ARP request to the user from which it was created. And after the successful ARP, ICMP will take place. As sown in the following figure:

Domain Name Server (DNS)
Create a Topology as shown in the following figure:
Assign IP addresses on Servers and PCs as below:
DNS Server (IP address 10.0.0.10 Subnet Mask 255.0.0.0)
Web Browser Server (IP address 10.0.0.20 Subnet Mask 255.0.0.0 DNS Server 10.0.0.10) Laptop 0 (IP address 10.0.0.1 Subnet Mask 255.0.0.0 and DNS 10.0.0.10) Laptop 1 (address 10.0.0.2 Subnet Mask 255.0.0.0 and DNS 10.0.0.10)

Now click on the DNS Server and configure it with the following setting:

Go on Laptop 0 web browser and write google.com. It successfully opens the requested application. As shown below:

Also check simulation Mode: First of all request will go to DNS server and after the successful DNS, HTTP request will be processed.

Check the PDU of DNS Server by clicking on the DNS as shown below:

Also check the PDU of HTTP packet at Web...
Continue Reading

Please join StudyMode to read the full document

You May Also Find These Documents Helpful

  • Ccna Essay
  • Ccna Essay
  • CCNA Essay
  • Essay about Ccna
  • Ccna Essay
  • Essay about Ccna
  • CCNA 1 Essay
  • Ccna Lab Manual Essay

Become a StudyMode Member

Sign Up - It's Free