Case Study: Honda Siel Cars India Ltd.
AREER EPISODE -2
CE 1.1.1 DATES AND DURATION
The time for completion of the project was 8 weeks ie.May 2010 to June 2010, including understanding the entire assembly of cars at the manufacturing facility of Honda Siel Cars India Ltd and finding a suitable project in a highly automated company like HONDA and completing the project in a stipulated time.
CE 1.1.2 GEOGRAPHICAL LOCATION
Greater Noida
CE 1.1.3 Name Of The Institution
Honda Siel Cars India Ltd
CE 1.2 BACKGROUND
CE1.2.1 Nature of Project
As per the curriculum adopted by National Institute of Technology , Rourkela,; every individual pursuing Bachelors degree in any stream has to undergo mandatory Industrial exposure of 2 months after the end of 6th semester and before the starting …show more content…
As proper guidance was available with me so it was my responsibility to understand each and every aspect of the project within a given time and start off with its experimental design, specimen fabrication, collecting the relevant technical facts,planning project report preparation, problem analysis, optimization etc is concerned. Also I have to ensure at different stages that our requirements are meeting to the requirement of the …show more content…
Torquing = 180 +/- 20 Kgfcm
Bond Applied: - Three bond seal 1215 grade
3. Torque wrench Specifications-
Figure above shows Various parts of a Torque Wrench
Model: - QSP50N
Capacity: - 10~50 N.m / 100~500 Kgfcm
Maximum Hand Power: - 281 N
Mass: - 0.4 kg
Effective length (L): - 179 mm
Overall Length (L’): - 248 mm a: - 9.53 mm b: - 25.6 mm c: - 11 mm
D:- 34 mm d: - 25.5 mm d’: - 21.7 mm
R: - 16 mm w: - 11.2 mm
4. Operations Performed at the assembly stage –
a. Apply bond on its 3-4 thread and make sure that bond does not close the hole of Oil Pressure Switch.
b. Manually tighten its 1-2 threads by hands.
c. Tighten it by torque wrench (QSP50N) until tick sound generates.
d. Another person checks it visually and put a mark via permanent marker on it.
5.Other Details
No. of threads in oil pressure switch = 9
No. of rotation of switch required = 9
Rotation caused by hand tightening = 1-2
Rotation required with torque wrench = 7-8
Motion of torque wrench at one manual stroke =120 degrees
Therefore no. of manual strokes required = (7-8)*3=
CE 1.1.1 DATES AND DURATION
The time for completion of the project was 8 weeks ie.May 2010 to June 2010, including understanding the entire assembly of cars at the manufacturing facility of Honda Siel Cars India Ltd and finding a suitable project in a highly automated company like HONDA and completing the project in a stipulated time.
CE 1.1.2 GEOGRAPHICAL LOCATION
Greater Noida
CE 1.1.3 Name Of The Institution
Honda Siel Cars India Ltd
CE 1.2 BACKGROUND
CE1.2.1 Nature of Project
As per the curriculum adopted by National Institute of Technology , Rourkela,; every individual pursuing Bachelors degree in any stream has to undergo mandatory Industrial exposure of 2 months after the end of 6th semester and before the starting …show more content…
As proper guidance was available with me so it was my responsibility to understand each and every aspect of the project within a given time and start off with its experimental design, specimen fabrication, collecting the relevant technical facts,planning project report preparation, problem analysis, optimization etc is concerned. Also I have to ensure at different stages that our requirements are meeting to the requirement of the …show more content…
Torquing = 180 +/- 20 Kgfcm
Bond Applied: - Three bond seal 1215 grade
3. Torque wrench Specifications-
Figure above shows Various parts of a Torque Wrench
Model: - QSP50N
Capacity: - 10~50 N.m / 100~500 Kgfcm
Maximum Hand Power: - 281 N
Mass: - 0.4 kg
Effective length (L): - 179 mm
Overall Length (L’): - 248 mm a: - 9.53 mm b: - 25.6 mm c: - 11 mm
D:- 34 mm d: - 25.5 mm d’: - 21.7 mm
R: - 16 mm w: - 11.2 mm
4. Operations Performed at the assembly stage –
a. Apply bond on its 3-4 thread and make sure that bond does not close the hole of Oil Pressure Switch.
b. Manually tighten its 1-2 threads by hands.
c. Tighten it by torque wrench (QSP50N) until tick sound generates.
d. Another person checks it visually and put a mark via permanent marker on it.
5.Other Details
No. of threads in oil pressure switch = 9
No. of rotation of switch required = 9
Rotation caused by hand tightening = 1-2
Rotation required with torque wrench = 7-8
Motion of torque wrench at one manual stroke =120 degrees
Therefore no. of manual strokes required = (7-8)*3=