Preview

Are You Acquainted with Inspection standard of Ball Mill

Satisfactory Essays
Open Document
Open Document
408 Words
Grammar
Grammar
Plagiarism
Plagiarism
Writing
Writing
Score
Score
Are You Acquainted with Inspection standard of Ball Mill
The inspection content of ball mill includes: 1, after the repair: the main check the oil amount, adjust each clearance, fortified by bolt, the replacement of individual liner or liner wear examination, repair feeder; 2, minor repair: check cleaning measurement of tooth surface wear, check the liner wear, replace if necessary; 3, repair: change the incoming parts, replacement drive small gear wheel and bearing, reducer strip inspection. Big gear in run 3-5 years of use can be adjusted according to situation, hollow shaft run 3-5 years should be measured; 4, overhaul: disintegration inspection cleaning, measuring, according to the wear condition, repair or replace the big gear, hollow shaft, spherical, drive shaft and pinion and cylinder, is repaired change regulation of the electrical components, electrical equipment repair, commissioning acceptance work must be conducted. However, do you know the inspection standard of ball mill?

The inspection standard of ball mill is in the following:

1, two bearing base processing surface on the same horizontal plane, center distance tolerance of 1 mm, longitudinal centerline deviation 0.5 mm, not parallel axis deviation 0.5 mm per meter.

2, tile spherical uniform can contact Angle; Within every 50 x 50 was not less than 1-2 PM;Hollow shaft and tile interface should be 90 °, 100 ° per square inch of not less than 2 points, journal and bearing clearance approximately the same on both sides;

3, cylinder flange fitting surface shall ensure good contact with the front end cover, are not allowed to add gasket, two hollow shaft alignment tolerance is less than 0.8 mm. Big gear ring and cylinder end cover assembly correction, connectors should be strong thrust, superior dowel, ring gear radial swing is not greater than 0.5 mm, axial runout no greater than 0.84 mm;

4, lining board installation should be according to the loading end cover, cylinder liner should start with population, according to the requirements of

You May Also Find These Documents Helpful

  • Good Essays

    Nvq 2 Cuting Assesnent

    • 1083 Words
    • 5 Pages

    Next take sections from each side facing the front of the client take each side section and over direct at 45’degress maintaining…

    • 1083 Words
    • 5 Pages
    Good Essays
  • Good Essays

    Nt1310 Final Exam Answers

    • 615 Words
    • 3 Pages

    The diameter of the shaft must be uniform throughout and there are two further design requirements : - the angle of twist between A and C must not exceed 1.5o; - the maximum permissible shaft shear stress is (MAX = 60 MPa. Determine the minimum shaft diameter that may be used, G = 77 GPa.…

    • 615 Words
    • 3 Pages
    Good Essays
  • Satisfactory Essays

    The hydraulic system of vertical mill is an important system, the main function of the hydraulic system is to break the grinding roller, which is when the internal grinding cavity wear parts wear, can stop open on both sides of the grinding roller mill, to replace the inside parts or repair. This type vertical roller mill including the hydraulic station, connected with the grinding roller cylinder and hydraulic pipe and other components.…

    • 429 Words
    • 2 Pages
    Satisfactory Essays
  • Good Essays

    Wet ball mill is the material being broken to smash the key equipment.By feeding, discharging part, turning part, a transmission of the main part.Mill widely used in cement, silicate products, new building materials, refractory materials, fertilizer, black and non-ferrous metal processing and glass ceramic production industry, for all kinds of ores and other materials may be grinding of dry or wet grinding.Ball mill used for a long time, always more or less appear some problems.Our company based on years of experience for our customers to summarize the common problems in the ball mill.…

    • 478 Words
    • 2 Pages
    Good Essays
  • Good Essays

    Different Types of Mills

    • 722 Words
    • 3 Pages

    Ball Mill is an efficient tool for grinding many materials into fine powder. The Ball Mill is used to grind many kinds of mine and other materials, or to select the mine. It is widely used in building material, chemical industry, etc. There are two ways of grinding: the dry way and the wet way. It can be divided into tabular type and flowing type according to different expelling mine.…

    • 722 Words
    • 3 Pages
    Good Essays
  • Good Essays

    Ball mill is a widely used ultra-fine grinding mill in industrial production. Ball mill has a variety of types, according to different ways of discharging materials, ball mill could be in grate and overfall style. There are also tube mill, cone mill, etc.…

    • 420 Words
    • 2 Pages
    Good Essays
  • Satisfactory Essays

    However, a number of companies are often overlooked mill troubleshooting , and underestimation for failures , resulting in large economic losses suffered by businesses . Therefore , processing enterprises in the production process and in particular the need for mill equipment and other critical equipment condition and the cause of deterioration and changes in operational information for diagnosis .…

    • 259 Words
    • 2 Pages
    Satisfactory Essays
  • Satisfactory Essays

    Ball mill is the main crushing grinding equipment widely used in power plant, cement, mining, chemical, metallurgical and other industries production at home and abroad. Hongxing is a famous ball mill manufacturer in China,which was established in 1960. Our company development newly developed a type of cone ball mill,more cost-effective and more trusted by customers. Cone ball mill have a higher technical indexes and efficiency than old-fashioned ball mill,so yields also greatly enhanced.…

    • 336 Words
    • 2 Pages
    Satisfactory Essays
  • Good Essays

    Mill ball, as main materials for ball mill processing, is very important for improving output of ball mill. The quality of steel ball, the reasonable ratio and different mining conditions will all affect the output of ball mill. Grinding ballmanufacturers must know about these factors which affect the output of ball mill for the sake of customers.…

    • 432 Words
    • 2 Pages
    Good Essays
  • Satisfactory Essays

    As for the shoes is too big, feeding device electrical overload; For shoes is too small, no ball.Thus the skilled operation skill is vital to guarantee the normal work of the ball. Hydraulic pressure protection device of high pressure ball machine is composed of hydraulic pump high pressure oil into the hydraulic cylinder, the piston to produce axial displacement. Non-ferrous and ferrous metals ore powder ball block, directly into the furnace smelting, increase the added value.Metallurgical waste materials, auxiliary materials need to be on the stove, all need to pressure the ball machine to complete. The final products pressed by ball machine, it can save energy and protect environment, easy to transport, improve the utilization of waste, with good economic and social benefits.High pressure ball machine working process:High pressure on the roller pressure ball machine industrial use and improvement after many years, compared with other similar products, this series high pressure ball machine successful rate, small power consumption, compact structure, convenient maintenance and debugging and so on obvious advantages, magnesium smelting process was numerically simulated with no doubt is the key to a kind of ideal equipment. To satisfy the requirement of material forming, to pressure screw used electromagnetic speed regulating motor, speed control mode is manual type, the user may be changed into a ball the basis the circumstance to the compressor speed to achieve the highest ball rate and maximum capacity, suppression of material by the sieving machine, oversize qualified pellets for packaging, undersize material can be mixed with new material and then to return storehouse briquetting.High pressure ball press machine is a powder material is compressed into the ball. The application of pressure ball machine is very extensive, pressure groups, on the following materials for granulating or pressure, such as aluminum, activated carbon, alumina, bauxite, caustic soda,…

    • 351 Words
    • 1 Page
    Satisfactory Essays
  • Satisfactory Essays

    Before installing the drum,we must ensure that the parallelism between the two bearings of drum,the bearing elevation and levelness meet the design requirements.…

    • 320 Words
    • 2 Pages
    Satisfactory Essays
  • Powerful Essays

    2) At CNC turning machine, the side not to be threaded and inner diameter are machined and become 74mm and 27mm respectively.…

    • 3342 Words
    • 14 Pages
    Powerful Essays
  • Good Essays

    Conc. shall be proportioned to provide an average cylinder fc΄ and shall satisfy the durability criteria. Requirements for fc΄ shall be based on tests of cylinders molded and standard-cured in accordance with C 31 and tested in accordance with C 39. Cylinders' dimensions are 10*20 cm. or 15*30 cm. unless they are specified. fc΄ shall be based on 28-day tests.…

    • 2090 Words
    • 9 Pages
    Good Essays
  • Satisfactory Essays

    For a long time, ball mill has been a key equipment for high capacity grinding demand. Nowadays, vertical mill will be active in this field. You must want to know the comparison between them, please read as follows:…

    • 297 Words
    • 2 Pages
    Satisfactory Essays
  • Powerful Essays

    Floor Systems

    • 2358 Words
    • 10 Pages

    The depth of the floor construction and the opening with in it should be considered if it is to accommodate mechanical or electrical line with in the floor system.…

    • 2358 Words
    • 10 Pages
    Powerful Essays

Related Topics