Resistor Essays & Research Papers

Best Resistor Essays

  • about resistors - 2205 Words
    What is a Resistor? An electric resistor is a two-terminal passive component specifically used to oppose and limit current. A resistor works on the principle of Ohm’s Law which states that voltage across the terminals of a resistor is directly proportional to the current flowing through it. Ohm’s,Law: v=IR where V is the voltage applied across resistor, I is the current flowing through it, and R is the constant called resistance. The unit of resistance is ohms....
    2,205 Words | 8 Pages
  • types of resistor - 4093 Words
     Types of Resistors Navigation Tutorial: 1 of 9 Top of Form Bottom of Form The Different Types of Resistors Resistors ( R ), are the most fundamental and commonly used of all the electronic components, to the point where they are almost taken for granted. There are many different Types of Resistors available to the electronics constructor, from very small surface mount chip resistors up to large wirewound power resistors. The principal job of a resistor...
    4,093 Words | 15 Pages
  • Neutral Grounding Resistor - 1373 Words
    Neutral Grounding Resistors (NGR) for Transformers & Gen. Sets.: NGR is employed in AC distribution networks to limit the fault current which would flow from the transformer or generator neutral star point in the event of an earth fault in the systems. It is used when the neutral of supply transformer is accessible and its own impedance is not enough to limit fault current. The rating of the protection relays within the required time. For Grounding Neutral of Transformer or Generator,...
    1,373 Words | 5 Pages
  • Different Types of Resistors - 469 Words
    Different Types of Resistors Electrical engineering involves the study and development of different electrical technologies, which are used for different purposes. One device that is very common in engineering and in electrical engineering is a resistor. A resistor is nothing but a special electrical component that helps in the induction of electrical resistance in a given electrical circuit. The resistors can be made up of different elements and different materials and it depends on the...
    469 Words | 2 Pages
  • All Resistor Essays

  • Light Dependant Resistor - 1400 Words
    LDR Circuit Diagram: Here is the schematic for the circuit: Light Dependent Resistors Light Dependent Resistors (LDR) are also called photoresistors. They are made of high resistance semiconductor material. When light hits the device, the photons give electrons energy. This makes them jump into the conductive band and thereby conduct electricity. A photoresistor or light-dependent resistor (LDR) or photocell is a light-controlled variable resistor. The resistance of a photoresistor...
    1,400 Words | 5 Pages
  • Resistors in series and parallel. - 1193 Words
    Title: Resistors in Series and Parallel Date: 17/7/05 Aim: The aim of this experiment is to compare the predicted and actual resistance in a circuit of resistor combinations in series and in parallel. Background: A resistor is an electrical component/device that has electrical resistance. Resistors can be used in electric circuits for protection of components, voltage division or current control. In an ideal resistor the resistance remains constant regardless of the applied voltage or...
    1,193 Words | 7 Pages
  • Resistor and Total Resistance - 274 Words
    ECT 122 Week 3 iLab #1 Parts: Breadboard DC Power Supply Hand Held DMM Test leads Wire 1.0kΩ resistor 2.2kΩ resistor 3.3kΩ resistor 1. Identify the type of the following circuits as either serial or parallel. 2. List four characteristics of a series circuit. * Resistance: The total resistance is equal to the sum of the individual resistances. * Current: The current at any point in the circuit equals the current at all other points. The value of current depends on the...
    274 Words | 2 Pages
  • Resistors, Capacitors, and Inductors
    tResistors, Capacitors, and Inductors In partial fulfillment of the requirements In Electronics 2 Submitted to the Department of TLE Submitted by: Reyes, Zelly B. IV-Prestige August 1 Table of Contents TOPIC | PAGE | Resistors | | Definition | 1 | Usage | 2 | Classification and Types | 2 | Configuration | 5 | Generalization | 6 | Capacitors | | Definition | 7 | Usage | 8 | Classification and Types | 8 | Configuration | 10 | Generalization | 11 |...
    2,699 Words | 11 Pages
  • Resistor Color Code Guide
    RESISTOR COLOR CODE GUIDE 4- Band Code 1.0 KΩ +5% 1st 2nd Color Black Brown Red Orange Yellow Green Blue Violet Gray White Gold Silver None 1st Band 0 1 2 3 4 5 6 7 8 9 2nd Band 0 1 2 3 4 5 6 7 8 9 3rd Band 0 1 2 3 4 5 6 7 8 9 3rd Decimal Multiplier Tolerance 1 1 + 1% 10 10 + 2% 100 100 1,000 1K 10K 10,000 100K 100,000 1,000,000 1M 10,000,000 10M 100,000,000 1,000,000,000 + 5% 0.1 0.01 + 10 % + 20 % 4th 5th 4th 1st 2nd 3rd 254 Ω +1 % 5- Band Code Calculation Resistor Lead Left...
    2,317 Words | 6 Pages
  • Color Band Resistors - 916 Words
    Define the following: RESISTOR A resistor is a component of a circuit that resists the flow of electrical current. It has two terminals across which electricity must pass, and it is designed to drop the voltage of the current as it flows from one terminal to the other. Resistors are primarily used to create and maintain known safe currents within electrical components. Resistors are coated with paint or enamel, or covered in molded plastic to protect...
    916 Words | 4 Pages
  • resistor color code - 993 Words
    LESSON PLAN I. Objectives: At the end of the period, the students are expected to: 1. Identify the color coding of resistors; 2. Compute for resistance of a color-coded resistor; 3. Compute for minimum and maximum tolerance of a resistor. II. Subject Matter: Topic: Resistor Color Coding Reference: Technology and Home Economics II Luz Villanueva et. al pp. 200-203 Materials: Visual Aids Resistors Values Integration: Orderliness and Patience III....
    993 Words | 7 Pages
  • TRANSIENT ANALYSIS OF A RESISTOR-INDUCTOR (RL) CIRCUIT
    TRANSIENT ANALYSIS OF A RESISTOR-INDUCTOR (RL) CIRCUIT TOM CARNEY Table of Contents 1. Introduction………………………………………………………………………………….Page 2 2. Theoretical Analysis………………………………………………………………………Page 3 3. Questions related to constructed circuit……………………………………….Page 5 4. Conclusion…………………………………………………………………………………….Page 6 5. Works cited……………………………………………………………………………………Page 6 6. Illustrations…………………………………………………………………………………….Page 7-8 Transient...
    883 Words | 4 Pages
  • resistance - 6806 Words
    sad28078_ch02_023-046.qxd 12/5/11 4:54 PM Page 23 c h a p t e r 2 Resistance No pain, no palm; no thorns, no throne; no gall, no glory; no cross, no crown. —William Penn Historical Profiles Georg Simon Ohm (1787–1854), a German physicist, in 1826 experimentally determined the most basic law relating voltage and current for a resistor. Ohm’s work was initially denied by critics. Born of humble beginnings in Erlangen, Bavaria, Ohm threw himself into electrical research....
    6,806 Words | 81 Pages
  • Voltage Divider - 1369 Words
    School for Electronic and Computer Engineering Faculty of Engineering School of Electrical, Electronic & Computer Engineering EERI 213 VOLTAGE DIVIDER CIRCUIT Completed by: Mr I Coetzee 22678778 Submitted to: Dr P. van Vuuren 19 FEBRUARY 2013 1 School for Electronic and Computer Engineering DECLARATION I, Iwan Coetzee, declare this report is of my own work. Whenever contributions of others are involved, every effort was made to indicate this clearly, with due...
    1,369 Words | 9 Pages
  • Kuttan - 1285 Words
    Voltmeter Ammeter Component List: | 1x PIC16F876A - Programmed microcontroller 1x 2x16 LCD with Green or Blue Backlight 1x High quality PCB with red solder mask and plated through holes 1x 4MHz Resonator 1x LM7805 5V Voltage Regulator 1x 16x1 Gold Plated Female Header (PCB) 1x 16x1 Gold Plated Male Header (LCD) 1x 4x1 Gold Plated Male Header (LCD) 1x 100nF Ceramic Capacitor 1x 10K LCD Contrast Trimmer Potentiometer 1x 4x10K Network Resistor 2x 100K 1% Metal Film Resistor...
    1,285 Words | 5 Pages
  • ECT122 Wk1 Assignment - 685 Words
    Chapter 1 Principles of Electricity Practice Problems 1. One coulomb of charge passes a point every 20 seconds. Calculate the value of the current through the point. I = Q/t = 1 coulomb/20 seconds = 0.05C/s = 0.05 A 2. A total charge of 2.5x10^-3 C passes a point every 40 seconds. Calculate the value of the current through the point. I=Q/t = 2.5C/40s = 0.0625C/s = 0.0625 A 4. A total charge of 50x10^-3 C passes a point every 2.5 seconds. Calculate...
    685 Words | 4 Pages
  • physics research on LED - 591 Words
    a) Potentiometer A potentiometer is a manually adjustable electrical resistor that uses three terminals. It is a three-terminal resistor with a sliding contact that forms an adjustable voltage divider. If only two terminals are used, it acts as a variable resistor. A potentiometer measuring instrument is essentially a voltage divider used for measuring electric potential (voltage); the component is an implementation of the same principle, hence its name .Potentiometers are commonly used to...
    591 Words | 2 Pages
  • Comp 220 - 1463 Words
    | | iLab 5 of 7: Pointers and Pointer OperationsILAB OVERVIEW | | | | Scenario and Summary | | This lab will explore the use of pointers in several ways. Pointers will be used to dynamically allocate memory for new class objects on demand from the user, and they will be used to access class-member functions. Pointer arithmetic will be used to access and sort class objects according to criteria explained in the lab. Pointers are, essentially, address variables, or variables that...
    1,463 Words | 6 Pages
  • marriage is a private affair and the lottery
     EVOA Amy Dia 6/3/14...
    365 Words | 2 Pages
  • ECET wk 1 Lab01
    Laboratory Report Cover Sheet DeVry University College of Engineering and Information Sciences Course Number: ECET110 Professor: Laboratory Number: 1 Laboratory Title: Analysis of a Series Circuit using Simulation and Actual Construction Submittal Date: 3/8/2014 Objectives: 1. To construct a series circuit and measure its equivalent resistance. 2. To predict and verify electrical characteristics of a series circuit using Ohm’s Law and Kirchhoff’s Voltage Law. 3....
    692 Words | 0 Page
  • Engineer - 3104 Words
    Monitor and Control of Green House Environment Introduction The proposed project is an embedded system which will closely monitor and control the microclimatic parameters of a greenhouse on a regular basis round the clock for cultivation of crops or specific plant species which could maximize their production over the whole crop growth season and to reducing human intervention to the best possible extent in the existing system. This system comprises of sensors, passive components,...
    3,104 Words | 11 Pages
  • Eoct Em2 - 2655 Words
    Admin AEL-list tools repair locker APL-equipment fixed to the hull/vessel Mica: * (management information configuration allowances) tailored to a specific individual unit or unit class * Parts of mica: 1. Section a- equipment nomenclature sequence- list of apl/ael-sorted by equipment 2. Section b- hsc description sequence- list of apl/ael-sorted by structure coed 3. Section c- hsc code sequence- list of apl/ael-sorted by HSC 4. Section d-apl/ael number sequence-...
    2,655 Words | 13 Pages
  • automatic temp control fan
    The schematic of an automatic cooler fan for audio amplifiers is given here. The circuit automatically switch ON the cooler fan whenever the temperature of the heat sink exceeds a preset level. This circuit will save a lot of energy because the cooler fan will be OFF when the amplifier is running on low volume. At low volume less heat will be dissipated and it will not trigger the cooler fan ON. The temperature is sensed using an NTC (negative temperature coefficient) thermistor R2. Junction...
    347 Words | 2 Pages
  • Planning & Designing Experiment: Investigating the current - potential difference relationship (IV Characteristics) for a metal wire.
    Title: Investigating the current - potential difference relationship for a metal wire. Aim: To design an experiment that will facilitate an I - V Graph to be ascertained of a metal wire and thus find the resistance of the wire by deriving the inverse of the gradient of the graph. Skill: Planning & Designing Theory: Resistance is a property of any object or substance to resist or oppose the flow of an electrical current. The quantity of resistance in an electric circuit determines the amount of...
    1,264 Words | 3 Pages
  • Mecatronics - 10021 Words
    Solutions Manual INTRODUCTION TO MECHATRONICS AND MEASUREMENT SYSTEMS 3rd edition SOLUTIONS MANUAL David G. Alciatore and Michael B. Histand Department of Mechanical Engineering Colorado State University Fort Collins, CO 80523 Introduction to Mechatronics and Measurement Systems 1 Solutions Manual This manual contains solutions to the end-of-chapter problems in the third edition of "Introduction to Mechatronics and Measurement Systems." Only a few of the...
    10,021 Words | 205 Pages
  • The Sotry of My Life - 383 Words
    SEKOLAH VOKASIONAL NAKHODA RAGAM BDTVEC SKILLS CERTIFICATE 2 IN COMMUNICATION TECHNOLOGY MEASURE ELECTRICAL QUANTITIES Practical #1 – Measure Electrical Resistance Topic – Measure the Resistance using Analogue & Digital Multimeter Objective – Familiarize and learn how to use Multimeter Equipment/Tools * Resistor -10 * Digital Multimeter * Analogue Multimeter * Breadboard Circuit Diagram Block Diagram...
    383 Words | 2 Pages
  • Formal Report Title Page
    1FORMAL REPORT # 1 Experiment # 7 Title: SERIES-PARALLEL CIRCUITS Date: 15/OCT/2014 Name: AMISH PATEL Student #: 000356107 Lab Partner’s Name: MANPREET SINGH Per item grading: 0 - Missing 1 - Unacceptable 2 - Satisfactory 3 - Very Good 4 - Excellent! Neatness & Presentation Detailed Calculations Spelling & Grammar Tables/Graphs/Diagrams Statement of Purpose Procedure Equipment List Conclusion Data/Results In-Class Work and Report Sheets Attached...
    742 Words | 7 Pages
  • digital visitor counter - 4445 Words
     CONTENT TOPIC Page No. Acknowledgement 03 Objective 04 Introduction 05 Design...
    4,445 Words | 17 Pages
  • Design of Smart Lighting and PA System
    Design of Smart Lighting and PA System EE 2031 Mini Project National University of Singapore Department: Electrical & Computer Engineering Course: B. Eng. Electrical Engineering EE2031 Circuit and Systems Design Lab: Mini Project Design of Smart Lighting and PA System Module facilitators: Assoc. Prof Chim Wai Kin Dr Xiang Ning Mr Loke Yuan Ren Mr Sangit Sasidhar Lab Group: Friday_Room1_G2 (9am-12pm) Tan Kheng Loong A0087979X Wong Kok Keong A0087415B Wong Wei Long Andy...
    3,991 Words | 27 Pages
  • Magnetism - 1683 Words
    Student Exploration Circuits Vocabulary ammeter, circuit, current, electron, ohmmeter, Ohms law, parallel circuit, resistance, resistor, series circuit, voltage Prior Knowledge Questions (Do these BEFORE using the Gizmo.) Strings of holiday lights can be designed in one of two ways. In some strings of lights, each light is connected to the others along a single wire (in series). In others, each light is attached to its own wire (in parallel). Suppose a single light bulb burns out. How do you...
    1,683 Words | 4 Pages
  • ECT122 W3 ILab 3
    ECT 122 Week 3 iLab #3 Parts: Breadboard DC power supply Handheld DMM Test leads Wire 1.0kΩ resistor 1.2kΩ resistor 3.3kΩ resistor 10kΩ potentiometer 1. Using the circuit below, calculate the anticipated voltage drops across each resistor and record them below. Rt = R1 + R2 + R3 = 150Ω + 2.2kΩ + 3.3kΩ = 5650 x 10^3= 5.65kΩ I = V/R = 10V/5.65kΩ = 0.001769 x 10^-3 = 1.77mA Voltmeter1= 1.77mA x 150Ω = 0.2655 x 10^-3= 265.5mV Voltmeter2= 1.77mA x...
    499 Words | 3 Pages
  • How to Use a Homemade Seismograph
    MATERIALS 1 10Hz 395 Ohm Oyo-Geospace Geophone (seismic energy sensor) 1 Metal Ground Strike Plate (seismic energy source earth coupling mechanism) 1 Heavy Piece of Metal (seismic energy source) 1 Analog Voltmeter (for measuring sensed seismic signal amplitudes) 1 Amplifier DC Offset Circuit (for amplifying seismic signals sensed by geophone) -1 experimental socket board -6 volt lantern battery -47k Ohm resistor -2.2k Ohm resistor - ICL 7660 integrated circuit - IC...
    341 Words | 2 Pages
  • Notes - 1710 Words
    w w w e tr .X m eP e ap UNIVERSITY OF CAMBRIDGE INTERNATIONAL EXAMINATIONS International General Certificate of Secondary Education .c rs om * 4 7 6 3 1 4 0 5 4 7 * PHYSICS Paper 6 Alternative to Practical Candidates answer on the Question Paper. No Additional Materials are required. READ THESE INSTRUCTIONS FIRST Write your Centre number, candidate number and name on all the work you hand in. Write in dark blue or black pen. You may use a pencil for any diagrams, graphs or rough...
    1,710 Words | 8 Pages
  • Characteristic Electrical Output of a Pv Module
    Experiment No 2: Title: Characteristic electrical output of a PV module Objective: 1. To investigate the characteristic IV and power curves of a PV module 2. To determine maximum power transfer and the optimized load to obtain maximum power transfer from the solar cell to the load Components: 1. PV module 2. 2 units of Multimeters (mA Ammeter, Voltmeter) 3. Variable resistors (50 (, 100 (, 1 k(, 5 k() 4. Retort stand 5. Xenon Lamp (Solar simulator) 6. DC...
    395 Words | 4 Pages
  • Kirchoffs's Laws - 2249 Words
    A little history about Kirchoff Home Page A little history about Kirchoff A little history about Ohm Kirchoff's current and voltage laws Ohm's law Circuit analysis example Bibliography A little bit about the life and times of Gustav Robert Kirchoff: Gustav Robert Kirchoff was a German physicist born on March 12, 1824, in Konigsber, Prussia. Gustav Kirchoff's first research topic was on the conduction of electricity. As a result of this research, Kirchoff wrote the...
    2,249 Words | 5 Pages
  • ENG3104 Lab5 - 403 Words
    ENG3104 - Lab 6: Voltage Divider Bias Circuit Objective 1* To investigate the DC Biasing condition of a BJT. The purpose of this experiment is to verify the voltages and currents in a transistor voltage-divider bias circuit as well as to construct the dc load line. Voltage-divider bias is often used because the base current is made small compared to the currents through the two base resistors. Consequently, the base voltage and therefore the collector current are stabilized against changes in...
    403 Words | 3 Pages
  • Reproduce the Series Type Ohmmeter Using Pmmc of Ifsd = 30 Μa for Range of 0-10 Kω.
    UNIVERSITI TEKNIKAL MALAYSIA MELAKA (UTeM) FALKULTI KEJURUTERAAN ELEKTRONIK & KEJURUTERAAN KOMPUTER (FKEKK) BACHELOR DEGREE OF ELECTRONIC ENGINEERING (TELECOMUNICATION ELECTRONIC) (BENT) BENE 1183 ELECTRONIC INSTRUMENTATION TITLE : SERIES TYPE OHMMETER SUBJECT : BENE 1183 ELECTRONIC INSTRUMENTATION 1.0 Title: Reproduce the series type Ohmmeter using PMMC of Ifsd = 30 μA for range of 0-10 kΩ. 2.0 Objectives...
    2,017 Words | 8 Pages
  • ECT122 Wk5 ILab 1
    ECT 122 Week 5 iLab #1 Parts: Breadboard DC Power Supply Hand Held DMM Test leads Wire 100 Ω resistor, 120 Ω resistor, 220 Ω resistor, 330 Ω resistor 1. Identify each of these circuits. 2. Given the circuit below, calculate the values listed below. IT: _64mA__ IA: __18.18mA____ IB: __45.45mA__ VR1: _3.99V___ VR2: __5.99V__ VR3: _5.45V___ VR4: __4.54V___ Ra= R1+R2= 220Ω+330Ω= 550Ω Rb=R3+R4= 120Ω+100Ω= 220Ω Ia= Vs/Ra=...
    363 Words | 3 Pages
  • ECT122 W4 ILab 3
    ECT 122 Week 4 iLab #3 Parts: Breadboard DC Power Supply Handheld DMM Test leads Wire 1.2kΩ resistor 3.3kΩ resistor 4.7kΩ resistor 1. Calculate the current in each branch of the parallel circuit below. IT1=_10.8mA__ IR1=__1.7mA____ IR2=___2.4mA___ IR3=_6.7mA_____ IR1= Vs/R1= 8V/4.7kΩ= 0.001702 x 10^-3= 1.7mA IR2= Vs/R2= 8V/3.3kΩ= 0.002424 x 10^-3= 2.4mA IR3= Vs/R3= 8V/1.2kΩ= 0.00666 x 10^-3= 6.7mA IT1= I1+I2+I3= 1.7mA+2.4mA+6.7mA= 0.0108 x...
    348 Words | 2 Pages
  • Physics Potential Dividers - 254 Words
    In this investigation I am investigating how the temperature affects voltage and resistance with the potential divider. Resistance is affected by the potential difference and current in a circuit, as they are used to calculate resistance in a circuit. The higher the potential difference and the lower the current means higher resistance. Resistance (ohms/W)= Potential Difference (v) / current (amps/A) What is potential dividers? A potential divider is a simple circuit that includes...
    254 Words | 1 Page
  • Bldc Motor Operation Using Pld
    1. INTRODUCTION TO EMBEDDED SYSTEMS What is embedded system? An Embedded System is a combination of computer hardware and software, and perhaps additional mechanical or other parts, designed to perform a specific function. An embedded system is a microcontroller-based, software driven, reliable, real-time control system, autonomous, or human or network interactive, operating on diverse physical variables and in diverse environments and sold into a competitive and cost conscious market. An...
    13,536 Words | 46 Pages
  • Chapter1 Principlesofelectricalscience - 24893 Words
    LEVEL 2 UNITChapter 204 1 Principles of electrical science 11 Level 2 Electrical Installations (Buildings and Structures) This chapter covers: Chapter 1 the principles of electricity the principles of basic electrical circuits the principles of magnetism and electromagnetism the operating principles of a range of electrical equipment the principles of basic mechanics the principles of a.c. theory electrical quantities in Star Delta configurations. LO1 Matter – something that has weight...
    24,893 Words | 139 Pages
  • Security System - 22767 Words
    INTRODUCTION Wouldn’t it be nice to have your home take care of your thing for you, automatically, without you having to lift a finger? You bet it would. This is the promise of Home Automation. There are many different systems, especially in larger homes, that can benefit from being integrated. Some of these systems include security alarm, HVAC, audio/video & lighting. Home automation integrates together, enabling them to function more...
    22,767 Words | 84 Pages
  • Factors affecting the resistance of a wire
    Factors affecting the resistance of a wire Introduction: Resistance is a force, which opposes the flow of an electric current around a circuit. Resistance is measured in Ohms. George Ohm discovered that a circuit sometimes resists the flow of electricity. He called this 'RESISTANCE.' He even came up with a rule for working out the resistance of a circuit, which was: R= V ÷ I V- Volts I- Current R- Resistance Ohms law says the more resistance means more energy is needed for the current to...
    1,210 Words | 7 Pages
  • Filipino Nationlism - 21388 Words
    LEARNING MATERIALS ELECTRONICS Table of Contents Table of Contents I. INTRODUCTION II. OBJECTIVES III. PRE-ASSESSMENT IV. LEARNING GOALS/TARGETS V. COMMON COMPETENCIES A. KNOW Lesson 1. Occupational Health and Safety Lesson 2. Introduction to Electricity Lesson 3. Basic Structure of Matter Lesson 4. Electric Charge Lesson 5. The Valence Shell Lesson 6. Electrical Current Lesson 7. Voltage Lesson 8. Resistance B. PROCESS Lesson 1. OHM’s Law Lesson 2. Complete Circuit Lesson 3. Types of...
    21,388 Words | 84 Pages
  • Msp Based Volymeter - 1581 Words
    MSP430 BASED 30V VOLT METER | | | | Project overview: MSP430 BASED 30V VOLT METER: Introduction: This is a simple application of internal 10-bit ADC(analog to digital converter) of MSP430G2231 microcontroller.you can use this circuit to measure up to 30 v dc.. the possible applications are on bench top power supply or as a panel meter in various system. Overview of the project: Circuit description TEXAS INSTRUMENTS MSP430G2231 is the heart and brain...
    1,581 Words | 7 Pages
  • ECT122 Wk2 Assignment - 462 Words
    Chapter 3 Ohm’s Law and Power Practice Problems 13. Calculate the minimum acceptable power rating for the resistor in Figure 3.25a. V= 6V, R=120Ω 300 mW 14. Calculate the minimum acceptable power rating for the resistor in Figure 3.25b. V= 8V, R=16Ω 4W 21. Complete the following chart. Current Voltage Resistance Power a.10mA 200 mV 20 Ω 4W b. 500 µA...
    462 Words | 3 Pages
  • Reverse Engineering Paper - 2103 Words
    For our project we decided to disassemble and understand a Memphis 1 Channel Mono Block Amplifier. First we started by disassembling the amp down to the main circuit board. From there we assigned ourselves different components to understand what they were and how they worked inside the amp. We all researched our components and got back together to discuss and figure out the flow of power and operations of the amp worked. A general idea of what the amp does is as follows. Power comes into the...
    2,103 Words | 6 Pages
  • Lukas PIC Tutorial - 3166 Words
    PIC 16F877A Tutorials for Pitt Robotics Club Lukas Hoffmann, 2010 These tutorials demonstrate how to code simple input & output for your robot using the popular PIC 16F877A microcontroller. They help you get your sensors & motors working. The rest of the code is up to you! Questions? Visit our website: http://www.pitt.edu/~sorc/robotics/ Email: roboticsclubatpittsburgh@gmail.com The tutorials assume basic knowledge of programming and electronics. If you are new to programming,...
    3,166 Words | 14 Pages
  • automatic street light - 5574 Words
    ABSTRACT This project aims at designing and executing the advanced development in embedded systems for energy saving of street lights with light depending resistor. Nowadays, human has become too busy and he is unable to find time even to switch the lights wherever not necessary. This can be seen more effectively in the case of street lights. The present system is like, the street lights will be switched on in the evening before the sun sets and they are switched off the next day morning after...
    5,574 Words | 21 Pages
  • Describtion and Pratical Application of Electrical Components
    DESCRIBTION AND PRATICAL APPLICATION OF ELECTRICAL COMPONENTS NAME: AMAN VIKASH CHAND ID NO. : 2011001207 GROUP: TDEEN 1A TEACHER: MR. WILLIAM FONG YEAR: 2011 |RESISTORS | |Resistors(R) are a two-terminal passive electronic component which implements electrical resistance as a circuit element. They...
    19,553 Words | 61 Pages
  • Home Security System - 6899 Words
    Project Report On HOME SECUIRTY SYSTEM WITH GSM Submitted in the partial fulfillment of the requirement for the award of degree of Bachelors of Technology In Electronics & Communication Engineering [pic] Under The Guidance of Submitted by Mr. Surjit Gautum Sagandeep Sidhu Designation (Lecturer/Assistant Professor/Professor) 10801579 Department of Electronics & Comm. Engg Lovely Professional...
    6,899 Words | 27 Pages
  • Temperature Controller - 404 Words
    AUTOMATIC TEMPERATURE CONTROLLED FAN H ere is a circuit through which the speed of a fan can be linearly controlled automatically, depending on the room temperature. The circuit is highly efficient as it uses thyristors for power control. Alternatively, the same circuit can be used for automatic temperature controlled AC power control. In this circuit, the temperature sensor used is an NTC thermistor, i.e. one having a negative temperature coefficient. The value of thermistor resistance at...
    404 Words | 2 Pages
  • A Wheatstone Bridge - 2270 Words
    A Wheatstone bridge is an electrical circuit used to measure an unknown electrical resistance by balancing two legs of a bridge circuit, one leg of which includes the unknown component. Its operation is similar to the original potentiometer. It was invented by Samuel Hunter Christie in 1833 and improved and popularized by Sir Charles Wheatstone in 1843. One of the Wheatstone bridge's initial uses was for the purpose of soils analysis and comparison.[1]...
    2,270 Words | 7 Pages
  • PC-Based Lighting and Fan System
    i De La Salle Lipa College of Information Technology and Engineering Electronics Engineering Department PC – Based Lighting and Fan System Gesmundo, Kaycee Kimberly S. Marquez, Mark Aries J. Mea, Kit Arvin C. Perez, Omar Mikhail I. Tirones, Jefferson A. Umali, Max Oliver M. T4A March 2012 Engr. Robert G. De Luna Instructor i Table of Contents page I. Introduction 1 II. Physical Description 2 III. System Operation 3 IV. System Specification...
    8,781 Words | 71 Pages
  • burglar alarm - 6695 Words
    Table of Contents List of tables 3 List of Figures 4 1Introduction 5 2 Circuit diagram 6 3 Circuit components 7 3.1 LDR 7 3.2 Resistors 8 3.2.1 Color code 8 3.3 IR LED 9 3.4 LED 11 3.5 OP-AMP 12 3.5.1 OP AMP LM 324 13 3.6 Transistor 15 3.6.1 Transistor 2N2222 15 3.7 SCR 16 3.7.1 SCR C106MG 18 C106MG 19 3.8V Battery 19 3.9 Photo diode 20 Principle of operation 21 3.9.1 IR Photo diode 21 3.10 Switches 22 3.11 Buzzer 23 3.11.1Mechanical buzzer 24 3.11.2 Electromechanical buzzer 24 3.11.3 Piezo...
    6,695 Words | 25 Pages
  • Lab Report - 1453 Words
    Ohm’s Law II Abstract: The purpose of this experiment is to demonstrate how non-ohmic devices respond on a direct circuit. Furthermore, we also explored their behavior when they were connected in different configurations. In order to accomplished this we used a capacitor, diode, resistor, and battery. We ran a series of experiments that generated graphs and equations, which can explain the relationship between voltage and time for capacitors and diodes. Non-ohmic resistors are also...
    1,453 Words | 5 Pages
  • ECT122 W1 ILab 3
    ECT 122 Week 1 iLab #3 Parts: Breadboard Handheld DMM DC power supply Test leads Resistor kit 1. List the functions available on the DM717 handheld digital multimeter (DMM). This meter can measure three basic electrical properties voltage, current and resistance. 2. What is the function of the COM connection? What color lead is placed in this connection? It’s the common ground and is used in all measurements. Black lead is placed in this...
    452 Words | 4 Pages
  • Phy143 - 494 Words
    Discussion Through this experiment we have learnt about the basic concept of simulation and circuit design using TINA Sofware in the computer lab. TINA is a software that used to designing, simulating and analyzing analog, digital and mixed electronic circuits. Analysis result can be displayed as sophisticated diagrams or an range of virtual instruments. Any circuit can be design easily by using schematic editor. The components can be chosen from the large library. The parameters of each...
    494 Words | 2 Pages
  • Microcontroller Based Car Parking
    JOMO KENYATTA UNIVERSITY Of AGRICULTURE AND TECHNOLOGY FACULTY OF ENGINEERING Department of Electrical and Electronics Engineering P.O.BOX 62000-00200, NAIROBI EEE 2501: FINAL YEAR PROJECT REPORT TITLE: MICRO CONTROLLER BASED VEHICLE PARKING SYSTEM (MICROBVPS) Author: GEORGE NGUGI KIBIA E26-0668/03 Supervisor: MR. BAARIU A.M This report is submitted in partial fulfillment of the requirement for the award of BSc. Degree in Electronics and Computer Engineering of Jomo Kenyatta University of...
    17,084 Words | 137 Pages
  • Parallel and Series Combination Circuits
    Page 1 of 5 Name: ______________________________ ECET 231 - Circuit Analysis I Lab 6 Series-Parallel DC Circuits Objective: Students successfully completing this lab will accomplish the following objectives: 1. Gain experience analyzing and verifying, by measurements, the characteristics of series-parallel resistive circuits. 2. Increase understanding of the relationship of voltage, current and resistance in a series-parallel circuit 3. Learn to compute currents through the use of...
    1,034 Words | 6 Pages
  • Review Papers in Science - 4345 Words
    1. How much work does a person do in pushing a box with a force of 10 N over a distance of 4.0 m in the direction of the force? (A) 0.4 J (B) 4.0 J (C) 40 J (D) 400 J (E) 4000 J 2. A person pushes a 10 kg box at a constant velocity over a distance of 4 m. The coefficient of kinetic friction between the box and the floor is 0.3. How much work does the person do in pushing the box? (A) 12 J (B) 40 J (C) 75 J (D) 120 J (E) 400 J 3. How much work does the force of gravity do in pulling a 10 kg box...
    4,345 Words | 18 Pages
  • Unimelb Foundations of Electrical Networks Exam Paper
    Student Number: ....................... . THE UNIVERSITY OF MELBOURNE Semester 2 Assessment November 2012 Department of Electrical and Electronic Engineering ELEN20005 FOUNDATIONS OF ELECTRICAL NETWORKS Time allowed: 180 minutes Reading time: 15 minutes This paper has 28 pages including the 3-page Formulae Sheet The test is printed single-sided. Authorised materials: Only Melbourne-School-of-Engineering-approved (with MSE approval sticker) electronic calculators are permitted. Instructions to...
    2,599 Words | 27 Pages
  • Student - 12948 Words
    SCADA BASED MONITORING AND CONTROLLING USING ZIGBEE Submitted in complete fulfillment of the requirements For the degree of BACHELOR OF ENGINEERING BY ANSARI MOHAMMAD ADNAN ROHIT JETHMALANI PANKAJ SAWANT RAVI KUMAR Under the guidance of MRS. SUNITA SHARMA (internal guidance) DEPARTMENT OF ELECTRONICS AND TELECOMMUNICATION ENGINEERING UNIVERSITY OF MUMBAI 2011-2012 AN AFFILIATE OF THE UNIVERSITY OF MUMBAI...
    12,948 Words | 51 Pages
  • ECT122 W3 ILab 1
    ECT 122 Week 3 iLab #1 Parts: Breadboard DC Power Supply Hand Held DMM Test leads Wire 1.0kΩ resistor 2.2kΩ resistor 3.3kΩ resistor 1. Identify the type of the following circuits as either serial or parallel. 2. List four characteristics of a series circuit. 1) The total current is the same everywhere in the circuit. 2) A series circuit only has one path for current to flow. 3) The sum of all the voltages sources is equal to the sum of all the voltage...
    256 Words | 2 Pages
  • Physics Isa - 5705 Words
    Introduction I have chosen to investigate a factor that affects the output of a potential divider circuit. A potential divider is resistors connected in series across a voltage source; used to obtain a desired fraction of the voltage. A resistor is a device having resistance to the passage of an electric current which affects the output voltage (Vout). The factors that I could investigate are changing the resistance of r2 and record the output (Vout), or use a light-dependent resistor (LDR) and...
    5,705 Words | 17 Pages
  • Thermistors - 3262 Words
    The Software is the Instrument NATIONAL INSTRUMENTS Application Note 065 ® ® Measuring Temperature withThermistors – a Tutorial David Potter Introduction Thermistors are thermally sensitive resistors used in a variety of applications, including temperature measurement. This application note discusses this application of thermistors, including basic theory and how to interface thermistors to modern data acquisition systems. Thermistor Overview A thermistor is a piece of...
    3,262 Words | 14 Pages
  • ECT122 Wk3 Assignment - 456 Words
    Chapter 4 Series Circuit Practice Problems 1. Each of the following resistor combinations is connected as shown in figure 4.29. For each combination, calculate the total circuit resistance. R1 R2 R3 R4 a.1kΩ 220Ω 330Ω 1.1kΩ = 1kΩ+220Ω+330Ω+1.2kΩ=2650 x = 2.65kΩ b. 10Ω 18Ω 47Ω 200Ω= 10Ω+18Ω+47Ω+200Ω= 275Ω c. 150Ω 220Ω 820Ω 51Ω= 150Ω+220Ω+820Ω+51Ω=1241 x = 1.241kΩ d. 10kΩ 91kΩ 5.1kΩ...
    456 Words | 2 Pages
  • Baseball Scoreboard - 393 Words
    Baseball Scoreboard   Lee King, Henry Johnson, Demetrius Jackson, Bennie Chandler, Marcus Rice Parts List           3-Green LED’s Resistor 2-Red LED’s Resistor 5-330 Ohm Resistors 2-74175 OR Gate 3-1 k ohm Resistors 2-NO Push Buttons 2-555 Timers 1-0.01 uf Capacitor 1-0.1 uf Capacitor 1-10 k Ohm Resistor 1-22 k Ohm 1-1.0 M Ohm Information      A counter uses flip-flops to “remember” the last count until the clock pulse occurs. A shift register can store several events...
    393 Words | 3 Pages
  • 2010 Physics Multiple Choice Cambridge
    UNIVERSITY OF CAMBRIDGE INTERNATIONAL EXAMINATIONS General Certificate of Education Advanced Subsidiary Level and Advanced Level PHYSICS Paper 1 Multiple Choice Additional Materials: Multiple Choice Answer Sheet Soft clean eraser Soft pencil (type B or HB is recommended) 9702/11 May/June 2010 1 hour *0280134660* READ THESE INSTRUCTIONS FIRST Write in soft pencil. Do not use staples, paper clips, highlighters, glue or correction fluid. Write your name, Centre number and candidate...
    3,380 Words | 22 Pages
  • Experiment: Kirchoff's Rule - 882 Words
    TITLE Caselyn De Guzman, Rosalinda Gelotin and Alyssa Camille Nano University of the Philippines Baguio, Department of Physics, Physics 102.1 c Abstract This paper aims to validate the Kirchhoff’s rule by comparing and accounting for discrepancies between the calculated and measured values i.e. the current and the potential difference across a network of resistors. The experiment is done by creating a circuit with three resistors of varying resistances (1000Ω, 470Ω, & 250Ω) connected...
    882 Words | 4 Pages
  • Electrical Engineering Lab Session
    ELECTRICAL ENGINEERING LABORATORY SESSION 1 Title: RESISTOR NETWORKS Name:Richard Lancaster Date: 11th Sep 2010.Student Name: Richard Lancaster. Id No: (09099972) Course: B.Sc. Engineering Science Subject: Electrical Engineering Lecturer: Dr Martin Hayes Objectives: 1. Introductory familiarisation with D.C measurements. 2. Introduction to the use of pSpice as a tool for emulating circuits. pSpice v9.1 can be downloaded from Moodle or via...
    1,424 Words | 8 Pages
  • Electrical Engineering FundamentalsBasic Concepts and Ohms
    Electrical Engineering Fundamentals Basic Concepts and Ohm’s Law EEF 1 ECS1300L Dr SMR Jones Resistance • In 1827 Georg Simon Ohm published the results of experiments using the recently invented electrochemical cell, invented by Italian Count Alessandro Volta. • Ohm found that the electrical current (I) flowing through a sample of material was directly proportional to the voltage (V) applied across the sample, i.e. V R I • This is known as “Ohm’s Law”. • The constant of proportionality, R,...
    1,305 Words | 14 Pages
  • ECT122 W4 ILab 2
    ECT 122 Week 4 iLab #2 Parts: Breadboard DC Power Supply Hand Held DMM Test leads Wire 220 Ω resistor 560 Ω resistor 1.0kΩ resistor 1. State Kirchhoff’s Current Law. The algebraic sum of the currents entering a node is equal to zero. 2. What is the equation for the total current in a parallel circuit? It= I1+I2+I3…. 3. Determine the total current in the following nodes. 1) It= 2mA+4mA+6mA= 0.012x10^-3=12mA 2) I + I1+I3= I2 I= 2mA+4mA= 1mA I= 1mA-...
    475 Words | 3 Pages
  • Signal Conditioning of Thermistor - 2794 Words
    Introduction Signal conditioning of thermistor Signal conditioning means manipulating an analogue signal in such a way that it meets the requirements of the next stage for further processing. Operational amplifiers(op-amps) are commonly employed to carry out the amplification of the signal in the signal conditioning stage. The signal conditioning equipment may be required to do linear processes like amplification, attenuation, integration, differentiation, addition and subtraction. They are...
    2,794 Words | 11 Pages
  • The Nightlight - 594 Words
    In this lab, we were given an LED nightlight circuit. Upon first glance we noticed all the components, the zener diode, 3 resistors, a capacitor, 4 diodes, a photocell, an LED light, and something we thought was a transistor. We knew the first thing to do was to identify all of the components and find out the rating for them. We had to use the microscope to determine the identifying numbers on the zener diode, the capacitor, and the, assumed, transistor. The zener diode read 1N5242B,...
    594 Words | 2 Pages
  • Physics Project - 1171 Words
    The following is a project made by anonymous: INTRODUCTION The general purpose photoconductive cell is also known as LDR – light dependent resistor. It is a type of semiconductor and its conductivity changes with proportional change in the intensity of light. There are two common types of materials used to manufacture the photoconductive cells. They are Cadmium Sulphide (CdS) and Cadmium Selenide (CdSe). Extrinsic devices have impurities added, which have a ground state energy closer to the...
    1,171 Words | 6 Pages
  • Semi-Detailed Lesson Plan in Electronics
    LESSON PLAN Subject : ELECTRONICS Materials needed : Chalk, Blackboard, Eraser, Visual Aids I. Topic : Resistor Color Coding II. Objectives At the end of the lesson, the students will 1. State the colors of the resistor color coding accordingly. 2. Name the value of resistors based on the color codes. 3. Appreciate the value of using codes. III. Activities 1. Prayer/Greetings/Introduction. 2. Review of the previous topic. What is resistor? 3....
    340 Words | 2 Pages
  • Wind - 2617 Words
    Submitted By A Minor Project Report On “DIGITAL SOIL MOISTURE TEST” In partial fulfillment of requirements for the degree of Bachelor of Technology In Electrical Engineering Guided by Prof. VINEET MEHTA Name of the student: BHOMARAM BHISNOI (10EJIEEOO6) JAGDEV(10EJIEE022)...
    2,617 Words | 10 Pages
  • Electricity and Magnetism - 1210 Words
    Electricity and Magnetism Electricity Circuit symbols Potential difference The energy which is delivered to an electric circuit comes from the supply. The greater the potential difference of the power supply the more energy is delivered. Potential difference is measured in volts, which has the unit symbol V. Cells in series The more chemical cells that are connected in series the greater the potential difference that they supply. The potential difference of a number of cells...
    1,210 Words | 6 Pages
  • Sensor Data Acquisition and Data Processing Using Microcontroller
    CHAPTER-1 INTRODUCTION 1.1 Project Title: Sensor Data Acquisition and Data Processing using Microcontroller 1.2 Objective: To learn basics of electronic sensors and microcontroller. Another objective is to learn techniques and processing electronic data with the help of microcontroller. 1.3 Project Description: Our project consists of the basic study of Electronic Sensors, Microcontrollers, Data Acquisition techniques, Data Processing techniques, Measurement of R with...
    6,176 Words | 26 Pages
  • physics lab ohms law
    New York City College of Technology Ohm’s law & resistors in parallel & in series Lab 4 Class: PHY 1434-E475 Due date: March, 13 20144 Group Names: Hisham Sageer Objectives: Our object is to confirm Ohm’s law by analyzing the dependence of the electrical current as a function of voltage and as a function of resistance. Also, we studied the current flow and voltage in series and parallel. Finally, the lab determined the equivalence resistance of series...
    838 Words | 4 Pages
  • PIC assignment - 2170 Words
    Computer Programming and Digital Systems Development of a Resistance Tester for Production Tests Content Introduction---------------------------------------------------------------------------------------3 Chapter 1 State Diagram------------------------------------------------------------------------5 Chapter 2 C Programming ---------------------------------------------------------------------8 Chapter 3 Circuit Diagram &...
    2,170 Words | 12 Pages
  • EWB_tutorial - 2606 Words
    Electronic WorkBench tutorial Introduction Electronic WorkBench (EWB) is a simulation package for electronic circuits. It allows you to design and analyze circuits without using breadboards, real components or actual instruments. EWB's click-anddrag operations make editing a circuit fast and easy. You can change parameters and circuit components on the fly, which make "what-if" analysis straight foreward. This tutorial is intended as a quick introduction to EWB's basic features. It...
    2,606 Words | 12 Pages
  • 3 - 764 Words
    Alexandria Hayford Honors Physical Science Instructor Durbin 03/06/15 3.03 Build Your Own Circuit Wokrsheet Part 1: Answer the following questions (20 points) 1. Name and describe the components needed to make a complete circuit. In order to make a complete circuit, you must include a voltage source and an unbroken path. The voltage source is typically a battery, and it is where the electric current is first created by the moving electrons. The unbroken path is generally made out of wire, and...
    764 Words | 3 Pages
  • Activity 112 Investigating Basic Circuits DLBIntroductionWhat
     Activity 1.1.2 Investigating Basic Circuits (DLB) Introduction What is an electrical circuit? How can you manipulate components and design a circuit that will do what you want it to? This guided activity will introduce you to some components, tools, and concepts that are fundamental in electronics. It will allow you to investigate and discover: What are voltage, current, and resistance? How are they related to one another? What are some of the basic components that make up simple circuits and...
    1,662 Words | 6 Pages
  • Introduction to Thermister - 1106 Words
    Thermistor A thermistor is a type of resistor whose resistance varies significantly with temperature, more so than in standard resistors. The word is a portmanteau of thermal and resistor. Thermistors are widely used as inrush current limiters, temperature sensors, self-resetting overcurrent protectors, and self-regulating heating elements. Thermistors differ from resistance temperature detectors (RTD) in that the material used in a thermistor is generally a ceramic or polymer, while...
    1,106 Words | 5 Pages
  • Introduction to Circuits -Lab Report
    ELEC 202 LAB 1 REPORT INTRODUCTION TO LABORATORY INSTRUMENTS AND RESISTIVE CIRCUITS Objectives: The aim of the first experiment is to become familiar with lab instruments, get an idea about their working structure and how to use them when necessary. In addition to that in the first part of the experiment our aim is to read color codes of resistors and get idea about how to use multimeter for resistor measurements. In the second part of the experiment our aim is to see the operation...
    1,498 Words | 11 Pages
  • Electric Circuit Lab Report Final
    TO: 1201 Section-002 Instructor FROM: Engineer Student DATE: February 16, 2015 RE: Electrical Circuit Project Lab Report The purpose of the Electrical Circuit project was to prepare students with the ability to work with mathematical and engineering calculations to design a breadboard. In order to create a breadboard with an accurate voltage drop between nodes, the resistor combinations and calculations need to be correct. Calculating the voltage drop between nodes was done through the...
    2,145 Words | 9 Pages
  • Resistance Box - 641 Words
    | Measurement of Electrical Resistance and Ohm’s Law | Physics Lab 204.001 | | | | Yewande Adeniyi | 9/22/2011 | | PROCEDURE 1. Connect the ammeter A, the voltmeter V, and the power supply PS to the Resistance Box. The basic circuit supply is series with a resistor. To measure the current in the resistor, the ammeter is placed in series. To measure the voltage across the resistor, the voltmeter is placed in parallel. 2. Vary the current through resistor R1 in...
    641 Words | 3 Pages
  • Evm Voting Machine - 7629 Words
    HBeonLabs Off. No. 46, 1st Floor, Kadamba Complex Gamma-I, Greater Noida (India) - 201308 Contact us: +91-120-4298000 +91-9212314779 info@hbeonlabs.com training@hbeonlabs.com www. hbeonlabs.com ELECTRONIC VOTING MACHINE INTRODUCTION This project is design for the student to make them understand the technology used in a now a day’s voting machine system, which is used in whole world. These voting machines are equipped with the CPU, which control the voting machine. The...
    7,629 Words | 26 Pages
  • The Resistance of a Piece of Wire - 1185 Words
    Data Analysis The investigation I did was to find the resistance of a piece if wire. The piece of wire is my dependent variable throughout the investigation. I changed the length of the wire in order to measure the resistance of each length. Plan In this investigation, a simple circuit will be set up to read the voltage and current when the length of the wire changes. The length will range from 10cm-80cm with intervals of 10cm. The length of the wire will be changed by moving the crocodile...
    1,185 Words | 4 Pages
  • LINEAR POSITION MEASUREMENT USING A MAGNETORESISTIVE SENSOR
    LINEAR POSITION MEASUREMENT USING A MAGNETORESISTIVE SENSOR Abstract: A smart transducer used to measure the linear displacement of an object in a magnetic field is presented. The application is to be safely used for demonstration purposes in the Playpen laboratory. The system uses an array of five HMC1501 Magnetoresistive (MR) sensors to sense the position of a magnet attached to the moving object. The system also has the ability to monitor the ambient operating temperature and detect if it...
    3,161 Words | 11 Pages
  • prepaid energy meter - 10309 Words
    CHAPTER- 1 INTRODUCTION 1.1 Introduction to our project The Electrical metering...
    10,309 Words | 36 Pages
  • Electrical Circuits: Assignment - 188 Words
     Activity 1.2.3 Electrical Circuits – Physical – Part 3 1 Explain the difference between a series and a parallel circuit. 1. Explain the difference between the voltage output at the battery and the voltage across each component in the series circuit. Explain the relationship between the current output at the power supply and the current through each component in the series circuit. Explain how your data support the relationships observed. 2. Explain why the current is the same between...
    188 Words | 1 Page
  • physics lab report of Circuits
     Lab 3. Dc circuits and Ohm’s law of measurments Helina Wolfe Tannaz Farnoudi and Najah Rouse Physics 246-205 Professor Joe Renaud 09/23/13 Word count:1453 Abstract: The aim of this experiment was to understand the relationship between the variables of Ohm’s law and how they are part of an operation of an electric circuit. Introduction: This experiment was done in two parts. The first part consisted of understanding how to determine the current, voltage and...
    1,342 Words | 5 Pages
  • Week 1 Practice Problems
    Maria Saavedra ECT122 Week 1 05/07/2014 Chapter 1Chapter 2 Chapter 3 Practice Problems *(Be sure to put the units in; volts, amps, etc.) 1.One coulomb of charge passes a point every 20 seconds. Calculate the value of the current through the point. I=Q/t = 1C/20s = .05C/s= .05 A x10^-3 C = 50mA 2.A total charge of 2.5 × 10-3 C passes a point every 40 seconds. Calculate the value of the current through the point. I=Q/t =0.0025C/40s= 6.25 C/s = 6.25 A 4.A total charge of 50 × 10-3 C passes a...
    581 Words | 3 Pages
  • witricity - 15971 Words
     Major project report WIRELESS TRANSMISSION OF ELECTRICITY Submitted by............. 1.Anurag Burman (0205ex081003) 2.Jayant Mukherjee (0205ex081006) 3.Kalyani Shekhar Chourasia (0205ex081007) 4.Shubhangi Agrawal (0205ex081026) 5.Swati Singh (0205ex081028) 6.Nitesh Prajapati (0205ex083D03)...
    15,971 Words | 54 Pages
  • Series and Parallel Circuit Elements
    Experiment 8: Series and Parallel Circuit Elements Laboratory Report Frenzyl Espinola, Anna Fermin, Loren Gabayeron, Kristal Fernandez Department of Math and Physics College of Science, University of Santo Tomas España, Manila Philippines Abstract The experiment is about the elements of series and parallel circuits. The laws on series and parallel resistors, as well as the color code for resistors were observed to calculate the total resistance. The proper connection for ammeter...
    1,580 Words | 7 Pages
  • Introduction to Electrical Engineering: Lab 1
    Introduction to Electrical Engineering: Lab 1 I. Purpose This lab was performed in order to become familiar with measuring voltage, current, and resistance using a voltmeter, ammeter, and ohmmeter. In addition, the property of electrical resistance will be studied with three different types of sensors. Lastly, the resistance associated with a small audio speaker will be explored. II. Introduction Three basic electrical concepts were examined in this lab: voltage, current, and...
    1,539 Words | 6 Pages


All Resistor Essays