• Switches and Router
    mode. Use the hostname command to change the name of the device—this name has local significance only. 20 Chapter 5: Basic Switch and Router Configuration Assigning Passwords Both the 1900 and the 2950 allow you to set up passwords to restrict access to both User and Privilege EXEC...
    Premium 20413 Words 82 Pages
  • Basic Static Route Configuration
    in the Addressing Table to apply an addressing scheme to the network devices. After completing the basic configuration, test connectivity between the devices on the network. First test the connections between directly connected devices, and then test connectivity between devices that are not...
    Premium 2587 Words 11 Pages
  • Note Ccna2
    learned skills including cabling devices, establishing a console connection, and basic IOS command line interface operation and configuration commands. You will also learn to save configuration files and capture your configurations to a text file. The skills presented in this lab are essential to...
    Premium 11885 Words 48 Pages
  • NETW204: Assignment 1
    mode. What is the major difference between this mode and user mode? Allows the use of all EXEC commands. This mode will allow for the ability to change, edit, and adjust any setting available. 5 What does the router prompt look like for this mode? Router# Basic Configuration Tasks (18 points...
    Premium 849 Words 4 Pages
  • Kalimunda Hakim Internship Report 2012
    ) between 2 or another device ,this bus should be empty and none of devices should not use the bus . In INTERNSHIP REPORT 8 FIGURE 1: SWITCH II.3. SOME CONFIGURATION OF SWITCHING Command switch>? switch>enable switch# switch#disable switch>exit switch#show version switch#show flash: switch#show mac...
    Premium 3744 Words 15 Pages
  • Ccna 2 Lab Book
    EXEC modes. The user EXEC mode allows only a limited number of basic monitoring commands. This is often referred to as a view-only mode. The user EXEC level does not allow commands that might change the configuration of the router. The user EXEC mode can be identified by the > prompt. The...
    Premium 118025 Words 473 Pages
  • It260
    Comprehensive Lab 4-9: CDP Commands 186 Task 1: Cabling, Basic Router Configuration, Workstation Configuration, and Verification 187 Task 2: Display the Values of the CDP Timers, the Interface Status, and the Encapsulation Used 190 Task 3: Display CDP Information About Other Devices 191 Task 4: Monitoring and...
    Premium 118029 Words 473 Pages
  • Ccna 2 Router and Routing Protocols Study Guide
    : Verify Full Connectivity Between All Devices in the Topology 494 Chapter 11 OSPF 495 496 496 Study Guide Introduction to OSPF Vocabulary Exercise: Matching 497 OSPF Concepts Exercise 498 Basic OSPF Configuration 500 Learn the OSPF Commands Exercise 500 Verify OSPF Configuration Exercise...
    Premium 99578 Words 399 Pages
  • Random
    . If you want to Telnet to a device, just enter the IP host name itself: l t t Router#london = Router#telnet london = Router#telnet 172.16.1.3 exec-timeout Command 23 no ip domain-lookup Command n Router(config)#no ip domain-lookup Router(config)# Turns off trying to automatically...
    2089 Words 9 Pages
  • NETW204 Assing 1
    to enter the privileged mode. What is the major difference between this mode and user mode? User mode is intended for the network technicians, operators, and engineers who have the responsibility to configure network devices. The privileged EXEC mode allows the user to make configuration changes...
    Premium 877 Words 4 Pages
  • Ethernet Router Technologies
    able to: Use the initial configuration dialog to create a basic configuration on a router. Verify that the configuration has been saved to NVRAM using a show command. References: Interconnecting Cisco Network Devices 1,Cisco Systems,Cisco Systems, Inc.,Cisco authorized courseware for CCNA...
    Premium 5312 Words 22 Pages
  • Doctor
    status Privileged EXEC mode command: show oam peer can show OAM link’s opposite device information, include opposite MAC address, manufactory OUI, manufactory information, mode configuration, maximum packet length, configuration version and function support information. If OAM link is not built up...
    Premium 87347 Words 350 Pages
  • Term Paper
    Show Commands Requirement | Cisco Command | View version information | show version | View current configuration (DRAM) | show running-config | View startup configuration (NVRAM) | show startup-config | Show IOS file and flash space | show flash | Shows all logs that the router has in its...
    Premium 694 Words 3 Pages
  • Erouting Eigrp Pt Practice Sba
    | 192.168.1.65 | Note: The password for user EXEC mode is cisco. The password for privileged EXEC mode is class. Step 1: Configure the Device Basics. Note: Initially, you can only access router E-Branch2 through the console connection on NetAdmin. a.     Configure the following on E-Branch2:          The...
    Premium 748 Words 3 Pages
  • Ccna2
    CCNA Exploration LAN Switching and Wireless: Basic Switch Concepts and Configuration Lab 2.5.1: Basic Switch Configuration Step 4: Determine which MAC addresses that the switch has learned. Display the learned MAC addresses using the show mac-address-table command in privileged EXEC mode. S1...
    Premium 51893 Words 208 Pages
  • Dell
    prompt will be changed to ?Router#". To go back to user EXEC mode, we need to use the disable command. Note that all the configuration works requires the administrator to be in the Privileged mode first. Put it this way, Privileged EXEC mode includes support for all commands in user mode plus those that...
    Premium 23861 Words 96 Pages
  • Bsr64K-R5.0.0-Command Reference Guide
    . Group Access All Command Mode Global Configuration Command Line Usage aaa accounting commands {exec | isp-ro | isp-rw | mso-ro | mso-rw | sysadmin} default {none | start-stop | stop-only | wait-start} {local | none | radius | tacacs} no aaa accounting commands [exec | isp-ro | isp-rw | mso-ro...
    Premium 97502 Words 391 Pages
  • Netw204 Quiz Answers
    . The process used by a router to accept a packet on one interface and forward it out another interface. a) Answer: Switching Function 24. A reference to the different parts of the Cisco IOS CLI. Different modes allow different kinds of commands (EXEC and configuration commands) and different...
    Premium 3305 Words 14 Pages
  • Notes
    accessed. The prompt currently being displayed is called User EXEC and the device is waiting for a command. The most basic form of help is to type a question mark (?) at the prompt to display a list of commands. S1> ? Which command begins with the letter ‘C’? connect b. At the prompt, type t...
    Premium 37268 Words 150 Pages
  • Lan Switching and Wireless Ccna Exploration Labs and Study Guide
    >enable Commands for Basic Router Configuration Description Switches from user EXEC mode to privileged EXEC mode Switches back from privileged EXEC mode to user EXEC mode Moves into global configuration mode Names the router CISCO Sets the enable password to class and encrypts it Configures a...
    Premium 102635 Words 411 Pages