Nano Station M2/M5 Loco Manual
Models: NanoStation M2/M5 NanoStation Loco M2/M5/M900
Introduction
Introduction
Thank you for purchasing a Nanostation M series product. This is a point-to-point CPE wireless device. This Quick Start Guide is for use with the following models:
Model NanoStation M2 NanoStation M5 NanoStation Loco M2 NanoStation Loco M5 NanoStation Loco M900 Operating Frequency 2403-2475 MHz 5170-5875 MHz* 2402-2482 MHz 5170-5875 MHz* 904-926 MHz Ethernet Ports 2 2 1 1 1
* Only 5745-5850 MHz is supported in the USA and Canada
Package Contents
UB I
NE T
UB I
ET ITI N QU
RKS WO
ITI N QU
UB I
NE T
UB I
ET ITI N QU
RKS WO
ITI N QU
NanoStation
24v PoE Adapter
Power Cord
Mounting Ties
* Products may be different from pictures and are subject to change without notice.
Installation Requirements
• 10 mm wrench • Shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the PoE. We recommend that you protect your networks from the most brutal environments and devastating ESD attacks with industrial-grade shielded Ethernet cable from Ubiquiti Networks. For more details, visit www.ubnt.com/toughcable
1
Quick Start Guide
Hardware Overview
Secondary Ethernet Port* * Secondary Ethernet Port included only on NanoStation M2 & M5
Secondary
Main
Reset
Main Ethernet Port
Note: Secondary Ethernet Port is capable of 24V Power over Ethernet output which can provide power to a secondary device. It can be enabled using the AirOS interface.
LEDs
LAN1 LAN2
Power The Power LED will light steady green when properly connected to a power source. LAN1 WAN/Main Ethernet The LAN1 Ethernet LED will light steady green when an active Ethernet connection is made to the Primary Ethernet Port and flash when there is activity. LAN/Secondary Ethernet The LAN2 Ethernet LED (on NanoStation M2/M5 only) will light steady green when an active Ethernet connection is made to the Secondary Ethernet Port. Signal These
Introduction
Introduction
Thank you for purchasing a Nanostation M series product. This is a point-to-point CPE wireless device. This Quick Start Guide is for use with the following models:
Model NanoStation M2 NanoStation M5 NanoStation Loco M2 NanoStation Loco M5 NanoStation Loco M900 Operating Frequency 2403-2475 MHz 5170-5875 MHz* 2402-2482 MHz 5170-5875 MHz* 904-926 MHz Ethernet Ports 2 2 1 1 1
* Only 5745-5850 MHz is supported in the USA and Canada
Package Contents
UB I
NE T
UB I
ET ITI N QU
RKS WO
ITI N QU
UB I
NE T
UB I
ET ITI N QU
RKS WO
ITI N QU
NanoStation
24v PoE Adapter
Power Cord
Mounting Ties
* Products may be different from pictures and are subject to change without notice.
Installation Requirements
• 10 mm wrench • Shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the PoE. We recommend that you protect your networks from the most brutal environments and devastating ESD attacks with industrial-grade shielded Ethernet cable from Ubiquiti Networks. For more details, visit www.ubnt.com/toughcable
1
Quick Start Guide
Hardware Overview
Secondary Ethernet Port* * Secondary Ethernet Port included only on NanoStation M2 & M5
Secondary
Main
Reset
Main Ethernet Port
Note: Secondary Ethernet Port is capable of 24V Power over Ethernet output which can provide power to a secondary device. It can be enabled using the AirOS interface.
LEDs
LAN1 LAN2
Power The Power LED will light steady green when properly connected to a power source. LAN1 WAN/Main Ethernet The LAN1 Ethernet LED will light steady green when an active Ethernet connection is made to the Primary Ethernet Port and flash when there is activity. LAN/Secondary Ethernet The LAN2 Ethernet LED (on NanoStation M2/M5 only) will light steady green when an active Ethernet connection is made to the Secondary Ethernet Port. Signal These