Mtech Thesis Rule

Only available on StudyMode
  • Download(s) : 664
  • Published : March 30, 2011
Open Document
Text Preview
DAV INSTITUTE OF ENGINEERING AND TECHNOLOGY JALANDHAR

Format for M.Tech Thesis synopsis
Title page: 1. Name of Student and PTU registration No cum Roll No 2. Present official Address with E-mail, telephone No 3. Branch1 (indicate F.T./P.T.) 4. Year of Admission 5. Number of subjects passed till date 6. Proposed Topic:

Introduction (should not exceed 3 pages including Figs.)

Brief Literature survey (should not exceed 3 pages)

Problem formulation: Need and significance of proposed research work (should not exceed 1page)

Objectives (should not exceed 1 page)

Methodology/ Planning of work (should not exceed 2 pages)

Facilities required for proposed work

Proposed Place of work

1

F.T.= Full-time, P.T. = Part-time

GUIDELINES FOR M.Tech THESIS
1. The thesis shall be computer typed (English- British, Font -Times Roman, Size-12 point) and printed on A4 size paper. 2. The thesis shall be hard bound with cover page in light green colour. The name of the candidate, degree (specifying the specialization), year of submission, name of the University including college name shall be printed in black on the cover [Refer sample sheet (outer cover)] 3. The thesis shall be typed on one side only with double space with a margin 3.5 cm on the left, 2.5 cm on the top, and 1.25 cm on the right and at bottom. 4. In the thesis, the title page [Refer sample sheet (inner cover)] should be given first then the Certificate by the candidate and the supervisor(s) in sequence, followed by an abstract of the thesis (not exceeding 1500 words). This should be followed by the acknowledgment, list of figures/list of tables, notations/nomenclature, and then contents with page no.s 5. In the body of the text, a reference should be indicated giving author name and year of publication in parenthesis such as (Singh and Shan, 2002). 6. The reference should be given at the end of the Thesis in alphabetical order indicating: i). The authors name and his initials ii). The title of the paper and name of the journal iii). The name of the book and the publisher iv) The number of the volume, page numbers, and the year of publication (v) standard abbreviation may be used in the names of the journals For Example: 1. Singh, S. and Shan, H. S. (2002) “Development of Magneto Abrasive Flow Machining Process”, International Journal of Machine Tools & Manufacturing, vol. 42, 2, 2002, pp. 953-959. 2. Laroiya, S.C. and Adithan, M. (1994), “Precision Machining of Advanced Ceremics” Proceeding of the International Conference on Advanced Manufacturing Technology (ICMAT - 94), 29-30 August 1994. University Teknoloi Malaysia, Johor Bahru, Malaysia, pp 203-210.

3. Adithan, M. and Gupta, A.B. (1996), “Manufacturing Technology”, New Age, International Publishers, New Delhi. 7. The diagrams should be printed on a light/white background, Tabular matter should be clearly arranged. Decimal point may be indicated by full stop (.). The caption for Figure must be given at the BOTTOM of the Fig. and Caption for the Table must be given at the TOP of the Table. 8. The graphs should be combined for the same parameters for proper comparison. Single graph should be avoided as far as possible. 9. Conclusions must not exceed more than two pages. 10. The thesis must consist of following chapters Chapter 1- Introduction Chapter 2- Literature Review Chapter 3- Present work (It can span in two to three sub chapters depending on the type and volume of the work) Chapter 4- Result and Discussion Chapter 5-Conclusions and future scope References Appendix or Annexure-I, II, III (if any)

Sample sheet (outer cover)

DESIGN AND IMPLIMENTATION OF A NETWORK TOOL
(24pt.)

THESIS (14pt.)
SUBMITTED IN PARTIAL FULFILLMENT OF THE REQUIREMENT FOR THE AWARD OF THE DEGREE OF (12pt.)

MASTER OF TECHNOLOGY (Computer Science/Electronic (14pt.)

SUBMITTED BY

RAJINDER KUMAR (14pt) April 2007

PTU Logo

PUNJAB TECHNICAL UNIVERSITY JALANDHAR, INDIA (14pt.)

Sample sheet...
tracking img