Electric Machinery Fundamentals
Stephen J. Chapman BAE SYSTEMS Australia
Instructor’s Manual to accompany Electric Machinery Fundamentals, Fourth Edition Copyright 2004 McGraw-Hill, Inc. All rights reserved. Printed in the United States of America. No part of this book may be used or reproduced in any manner whatsoever without written permission, with the following exception: homework solutions may be copied for classroom use. ISBN: ???
TABLE OF CONTENTS
CHAPTER 1: CHAPTER 2: CHAPTER 3: CHAPTER 4: CHAPTER 5: CHAPTER 6: CHAPTER 7: CHAPTER 8: CHAPTER 9: CHAPTER 10:
INTRODUCTION TO MACHINERY PRINCIPLES TRANSFORMERS INTRODUCTION TO POWER ELECTRONICS AC MACHINERY FUNDAMENTALS SYNCHRONOUS GENERATORS SYNCHRONOUS MOTORS INDUCTION MOTORS DC MACHINERY FUNDAMENTALS DC MOTORS AND GENERATORS SINGLE-PHASE AND SPECIAL-PURPOSE MOTORS
1 23 63 103 109 149 171 204 214 270 280 288 295 301
APPENDIX A: REVIEW OF THREE-PHASE CIRCUITS APPENDIX B: COIL PITCH AND DISTRIBUTED WINDINGS
APPENDIX C: SALIENT POLE THEORY OF SYNCHRONOUS MACHINES APPENDIX D: ERRATA FOR ELECTRIC MACHINERY FUNDAMENTALS 4/E
PREFACE TO THE INSTRUCTOR
This Instructor’s Manual is intended to accompany the fourth edition of Electric Machinery Fundamentals. To make this manual easier to use, it has been made self-contained. Both the original problem statement and the problem solution are given for each problem in the book. This structure should make it easier to copy pages from the manual for posting after problems have been assigned. Many of the problems in Chapters 2, 5, 6, and 9 require that a student read one or more values from a magnetization curve. The required curves are given within the textbook, but they are shown with relatively few vertical and horizontal lines so that they will not appear too cluttered. Electronic copies of the corresponding opencircuit characteristics, short-circuit characteristics, and magnetization curves as also supplied with the book. They are supplied in two forms, as MATLAB MAT-files and as ASCII text files. Students can use these files for electronic solutions to homework problems. The ASCII files are supplied so that the information can be used with non-MATLAB software. Please note that the file extent of the magnetization curves and open-circuit characteristics have changed in this edition. In the Third Edition, I used the file extent *.mag for magnetization curves. Unfortunately, after the book was published, Microsoft appropriated that extent for a new Access table type in Office 2000. That made it hard for users to examine and modify the data in the files. In this edition, all magnetization curves, open-circuit characteristics, short-circuit characteristics, etc. use the file extent *.dat to avoid this problem. Each curve is given in ASCII format with comments at the beginning. For example, the magnetization curve in Figure P9-1 is contained in file p91_mag.dat. Its contents are shown below: % % % % % % % % % % This is the magnetization curve shown in Figure P9-1. The first column is the field current in amps, and the second column is the internal generated voltage in volts at a speed of 1200 r/min. To use this file in MATLAB, type "load p91_mag.dat". The data will be loaded into an N x 2 array named "p91_mag", with the first column containing If and the second column containing the open-circuit voltage. MATLAB function "interp1" can be used to recover a value from this curve. 0 0 0.0132 6.67 0.03 13.33 0.033 16 0.067 31.30 0.1 45.46 0.133 60.26 0.167 75.06 0.2 89.74 iv
0.233 0.267 0.3 0.333 0.367 0.4 0.433 0.467 0.5 0.533 0.567 0.6 0.633 0.667 0.7 0.733 0.767 0.8 0.833 0.867 0.9 0.933 0.966 1 1.033 1.067 1.1 1.133 1.167 1.2 1.233 1.267 1.3 1.333 1.367 1.4 1.433 1.466 1.5
104.4 118.86 132.86 146.46 159.78 172.18 183.98 195.04 205.18 214.52 223.06 231.2 238 244.14 249.74 255.08 259.2 263.74 267.6 270.8 273.6 276.14...
Please join StudyMode to read the full document