8.3.1.2 Packet Tracer PDF

Packet Tracer - Skills Integration Challenge
Topology

Addressing Table
IPv4 Address
Device

Subnet Mask

Interface
IPv6 Address/Prefix
S0/0/0

172.31.6.1

255.255.255.252

S0/0/1

10.10.8.1

255.255.255.252

S0/1/0

209.165.200.226

255.255.255.224

R1

S0/0/0

172.31.6.2

255.255.255.252

R2

S0/0/1

10.10.8.2

255.255.255.252

S0/0/0

2001:DB8:A001:6::1/64

S0/0/1

2001:DB8:A001:7::1/64

S0/1/0

2001:DB8:CAFE:1::2/64

R3

S0/0/0

2001:DB8:A001:7::2/64

R4

S0/0/1

2001:DB8:A001:6::2/64

IPv4-Edge

IPv6-Edge

Scenario
In this activity, you are tasked with implementing EIGRP for IPv4 and IPv6 on two separate networks. Your task includes enabling EIGRP, assigning router-IDs, changing the hello timers, configuring EIGRP summary routes and limiting EIGRP advertisements.

© 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.

Page 1 of 3

Packet Tracer - Skills Integration Challenge

Requirements
EIGRP for IPv4


Implement EIGRP on IPv4 enabled routers using Autonomous System 1.
-

Use the classful network address for the loopback interfaces.

-

Use the wildcard mask to advertise the /30 networks between R1, R2 and IPv4-Edge.

-

Use the default method to only allow EIGRP updates out the active EIGRP serial interfaces.

-

Advertisements should not be summarized.



Configure a directly attached default route on IPv4-Edge and propagate it in EIGRP updates.



Configure the serial interfaces between R1, R2 and IPv4-Edge to send hellos every 10 seconds.



On R1 and R2, configure an EIGRP summary route for the loopback networks.
R1 Loopback Networks

R2 Loopback Networks

172.31.0.0/25

10.10.0.0/24

172.31.0.128/25

10.10.1.0/24

172.31.1.0/25

10.10.2.0/23

172.31.1.128/25

10.10.4.0/22

Summary: 172.31.0.0/24

Summary: 10.10.0.0/21



R1 and R2 should only have four EIGRP routes in the routing table, one of which is the default route
(D*EX). IPv4-Edge should only have two EIGRP routes in the routing table.



Verify R1 and R2 can ping the IPv4 Server. IPv4 Server should also be able to ping every loopback address on R1 and R2.

EIGRP for IPv6


Implement EIGRP on IPv6 enabled routers using Autonomous System 1.
-

Assign IPv6-Edge with the router-ID of 1.1.1.1

-

Assign R3 with the router-ID of 3.3.3.3

-

Assign R4 with the router-ID of 4.4.4.4



Configure a directly attached default route on IPv6-Edge and propagate it in EIGRP updates.



On R3 and R4, configure an EIGRP summary route for the loopback networks.
R3 Loopback Networks



R4 Loopback Networks

2001:DB8:1:1:A000::1/72

2001:DB8:1:1:BB80::1/76

2001:DB8:1:1:A100::1/72

2001:DB8:1:1:BB90::1/76

2001:DB8:1:1:A200::1/72

2001:DB8:1:1:BBA0::1/76

2001:DB8:1:1:A300::1/72

2001:DB8:1:1:BBB0::1/76

Summary: 2001:db8:1:1:a000::/70

Summary: 2001:db1:1:BB80::/74

R3 and R4 should only have four EIGRP routes in the routing table, counting the default external route.
IPv6-Edge should only have two EIGRP routes in the routing table.

© 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.

Page 2 of 3

Packet Tracer - Skills Integration Challenge


Verify R3 and R4 can ping the IPv6 Server. IPv6 Server should also be able to ping every loopback address on R3 and R4.

Suggested Scoring Rubric
Note: Packet Tracer does not currently grade EIGRP for IPv6 summary routes. Therefore, part of your grade depends on routing table verification by your instructor.

Scored Work

Possible
Points

IPv6-Edge Routing Table

10

Packet Tracer Score

90

Total Score

100

© 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.

Earned
Points

Page 3 of 3